On 2024/3/2 23:28, Jonas Karlman wrote:
Hi Christopher,

On 2024-03-02 15:34, Christopher Obbard wrote:
Some variants of the ROCK Pi 4 series contain an SPI flash chip, which can
be booted from. This patch enables support in U-Boot for building the
image for the SPI flash, support for booting U-Boot from the SPI flash
chip and support in U-Boot for accessing the SPI flash using `sf` commands.

Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come
populated with an SPI flash chip, but have the footprint on the board so
a user could solder their own to the board. With this patchset applied,
these board variants without an SPI flash chip still boot from MMC.

I have enabled support for both Winbond and XTX SPI flash devices since
different hardware variants have different devices populated:

  - `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG`
  - `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT`

The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI
flash chip from XTX:

     => sf probe
     SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 
MiB

In the interest of supporting all board variants and not regressing
existing users who boot from MMC, I have enabled support for booting from
both SPI flash chip variants in the defconfig and left the environment
storage location as MMC to not break existing users who have the
environment stored on MMC.

I have also enabled GigaDevice SPI flash chip support, since without it
U-Boot (unexplainably) fails to load with an error

What is the flash chip on this board? Does it a GigaDevice device?

This sound like some code address affect if your board has a flash chip other than GigaDevice.

:

     U-Boot SPL 2024.04-rc3-00002-g06b486900e2 (Mar 02 2024 - 13:20:45 +0000)
     Trying to boot from SPI
     load_simple_fit: Skip load 'atf-5': image size is 0!
     initcall failed at call 000000000029beec (err=-11: Try again)
     ### ERROR ### Please RESET the board ###
This is possibly because of pinctrl no being configured in SPL.

The pinctrl issue should affect all the SPI flash type, add GigaDevice driver should not able to fix

this issue.


Thanks,

- Kever

  I have a
big incoming rk3399 series that tries to fix this for most rk3399 boards.
It will be a variant of what I did in [1] for rk3328.

BROM will only configure pinctrl for each device it tries to locate IDB
from, so if it locates IDB in SPL it will not have configured emmc or
sd-card. So for SPL to be able to fall back on other storage it will
need to do proper pinctrl.

[1]https://patchwork.ozlabs.org/cover/1900345/

Building with `CONFIG_SPL_FIT_SIGNATURE=y` causes an error when booting
from SPI flash, so I disabled it:

     U-Boot 2024.04-rc3-00010-g2e7974a13b9 (Mar 02 2024 - 14:00:17 +0000)
     SoC: Rockchip rk3399
     Reset cause: unknown reset
     Model: Radxa ROCK Pi 4A
     DRAM:  initcall failed at call 0000000000228efc (err=-19: No such device)
     ### ERROR ### Please RESET the board ###
This is unexpected but if your u-boot.bin is close to or larger then 1
MiB the stack and pre-alloc heap may be overlapping with U-Boot proper
or the FDT. That can cause all sort of strange and unexpected issues :-)

Have another incoming series to address this for RK3328, RK3399 and
ROCK 5A [2]. Should hit list later today, it will be a rework of [3].

[2]https://github.com/Kwiboo/u-boot-rockchip/compare/2011cf069a8b...9767374d6a8a
[3]https://patchwork.ozlabs.org/cover/1900376/

Signed-off-by: Christopher Obbard<chris.obb...@collabora.com>
---

  arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi | 12 ++++++++++++
  configs/rock-pi-4-rk3399_defconfig         | 15 +++++++++++++--
  2 files changed, 25 insertions(+), 2 deletions(-)

diff --git a/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi 
b/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi
index 85ee5770add..04c152a291f 100644
--- a/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi
+++ b/arch/arm/dts/rk3399-rock-pi-4a-u-boot.dtsi
@@ -4,3 +4,15 @@
   */
#include "rk3399-rock-pi-4-u-boot.dtsi"
+
+/ {
+       chosen {
+               u-boot,spl-boot-order = "same-as-spl", &spi_flash, &sdhci, 
&sdmmc;
I would not recommend adding spi_flash here, especially if you have
SPL_FIT_SIGNATURE disabled, and even more so if someone accidentally
enable SPL_RAW_IMAGE_SUPPORT.

Ideally, we only load TPL/SPL+FIT from same storage, as provided by
same-as-spl, however, if we cannot load from the same storage that
TPL/SPL was loaded from, for recovery purposes it is typically easier to
fall back on sd-card followed by emmc.

Normally I would expect that if board does not boot TPL/SPL from SPI,
there is no real reason to try and load FIT from SPI.

If the FIT cannot be loaded from SPI with same-as-spl alone there is
possible some other issue that we need to resolve.

+       };
+};
+
+&spi1 {
+       spi_flash: flash@0 {
+               bootph-all;
+       };
+};
diff --git a/configs/rock-pi-4-rk3399_defconfig 
b/configs/rock-pi-4-rk3399_defconfig
index 83fc4ad7dab..3a38b51c46b 100644
--- a/configs/rock-pi-4-rk3399_defconfig
+++ b/configs/rock-pi-4-rk3399_defconfig
@@ -6,25 +6,28 @@ CONFIG_TEXT_BASE=0x00200000
  CONFIG_NR_DRAM_BANKS=1
  CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
  CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
+CONFIG_SF_DEFAULT_SPEED=10000000
  CONFIG_ENV_OFFSET=0x3F8000
  CONFIG_DEFAULT_DEVICE_TREE="rk3399-rock-pi-4a"
  CONFIG_OF_LIBFDT_OVERLAY=y
  CONFIG_DM_RESET=y
  CONFIG_ROCKCHIP_RK3399=y
+CONFIG_ROCKCHIP_SPI_IMAGE=y
  CONFIG_TARGET_EVB_RK3399=y
  CONFIG_SPL_STACK=0x400000
  CONFIG_DEBUG_UART_BASE=0xFF1A0000
  CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI=y
  CONFIG_SYS_LOAD_ADDR=0x800800
  CONFIG_PCI=y
  CONFIG_DEBUG_UART=y
  # CONFIG_ANDROID_BOOT_IMAGE is not set
-CONFIG_SPL_FIT_SIGNATURE=y
  CONFIG_LEGACY_IMAGE_FORMAT=y
  CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-rock-pi-4a.dtb"
  CONFIG_DISPLAY_BOARDINFO_LATE=y
  CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x2e000
+CONFIG_SPL_MAX_SIZE=0x40000
  CONFIG_SPL_PAD_TO=0x7f8000
  CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
  CONFIG_SPL_BSS_START_ADDR=0x400000
@@ -33,6 +36,8 @@ CONFIG_SPL_BSS_MAX_SIZE=0x2000
  # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
  CONFIG_SPL_STACK_R=y
  CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0xE0000
  CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
  CONFIG_TPL=y
  CONFIG_CMD_BOOTZ=y
@@ -52,6 +57,7 @@ CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names 
clock-names interrupt-parent
  CONFIG_ENV_IS_IN_MMC=y
  CONFIG_SYS_RELOC_GD_ENV_ADDR=y
  CONFIG_DFU_MMC=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
  CONFIG_ROCKCHIP_GPIO=y
  CONFIG_SYS_I2C_ROCKCHIP=y
  CONFIG_MISC=y
@@ -61,6 +67,10 @@ CONFIG_MMC_DW_ROCKCHIP=y
  CONFIG_MMC_SDHCI=y
  CONFIG_MMC_SDHCI_SDMA=y
  CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_SF_DEFAULT_BUS=1
Would recommend adding following to allow reading SFDP properties from
flash, it is what I am doing to all other rk boards with spi flash:

CONFIG_SPI_FLASH_SFDP_SUPPORT=y

Regards,
Jonas

+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_XTX=y
  CONFIG_ETH_DESIGNWARE=y
  CONFIG_GMAC_ROCKCHIP=y
  CONFIG_NVME_PCI=y
@@ -74,6 +84,7 @@ CONFIG_RAM_ROCKCHIP_LPDDR4=y
  CONFIG_BAUDRATE=1500000
  CONFIG_DEBUG_UART_SHIFT=2
  CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SPI=y
  CONFIG_SYSRESET=y
  CONFIG_USB=y
  CONFIG_USB_XHCI_HCD=y

Reply via email to