The RCG registers always have the same offsets, so only store the base
CMD register address and calculate the others relative to that.
Reviewed-by: Sumit Garg <sumit.g...@linaro.org>
Signed-off-by: Caleb Connolly <caleb.conno...@linaro.org>
---
drivers/clk/qcom/clock-apq8016.c | 39 +------------
drivers/clk/qcom/clock-apq8096.c | 28 +--------
drivers/clk/qcom/clock-qcom.c | 22 +++----
drivers/clk/qcom/clock-qcom.h | 16 +++--
drivers/clk/qcom/clock-qcs404.c | 122 +++++----------------------------------
drivers/clk/qcom/clock-sdm845.c | 16 +----
6 files changed, 39 insertions(+), 204 deletions(-)
diff --git a/drivers/clk/qcom/clock-apq8016.c b/drivers/clk/qcom/clock-apq8016.c
index e6647f7c41dd..5a5868169c89 100644
--- a/drivers/clk/qcom/clock-apq8016.c
+++ b/drivers/clk/qcom/clock-apq8016.c
@@ -22,13 +22,9 @@
#define APCS_GPLL_ENA_VOTE (0x45000)
#define APCS_CLOCK_BRANCH_ENA_VOTE (0x45004)
#define SDCC_BCR(n) ((n * 0x1000) + 0x41000)
-#define SDCC_CMD_RCGR(n) ((n * 0x1000) + 0x41004)
-#define SDCC_CFG_RCGR(n) ((n * 0x1000) + 0x41008)
-#define SDCC_M(n) ((n * 0x1000) + 0x4100C)
-#define SDCC_N(n) ((n * 0x1000) + 0x41010)
-#define SDCC_D(n) ((n * 0x1000) + 0x41014)
+#define SDCC_CMD_RCGR(n) (((n + 1) * 0x1000) + 0x41004)
#define SDCC_APPS_CBCR(n) ((n * 0x1000) + 0x41018)
#define SDCC_AHB_CBCR(n) ((n * 0x1000) + 0x4101C)
/* BLSP1 AHB clock (root clock for BLSP) */
@@ -37,33 +33,12 @@
/* Uart clock control registers */
#define BLSP1_UART2_BCR (0x3028)
#define BLSP1_UART2_APPS_CBCR (0x302C)
#define BLSP1_UART2_APPS_CMD_RCGR (0x3034)
-#define BLSP1_UART2_APPS_CFG_RCGR (0x3038)
-#define BLSP1_UART2_APPS_M (0x303C)
-#define BLSP1_UART2_APPS_N (0x3040)
-#define BLSP1_UART2_APPS_D (0x3044)
/* GPLL0 clock control registers */
#define GPLL0_STATUS_ACTIVE BIT(17)
-static const struct bcr_regs sdc_regs[] = {
- {
- .cfg_rcgr = SDCC_CFG_RCGR(1),
- .cmd_rcgr = SDCC_CMD_RCGR(1),
- .M = SDCC_M(1),
- .N = SDCC_N(1),
- .D = SDCC_D(1),
- },
- {
- .cfg_rcgr = SDCC_CFG_RCGR(2),
- .cmd_rcgr = SDCC_CMD_RCGR(2),
- .M = SDCC_M(2),
- .N = SDCC_N(2),
- .D = SDCC_D(2),
- }
-};
-
static struct pll_vote_clk gpll0_vote_clk = {
.status = GPLL0_STATUS,
.status_bit = GPLL0_STATUS_ACTIVE,
.ena_vote = APCS_GPLL_ENA_VOTE,
@@ -85,32 +60,24 @@ static int clk_init_sdc(struct msm_clk_priv *priv, int
slot, uint rate)
div = 4;
clk_enable_cbc(priv->base + SDCC_AHB_CBCR(slot));
/* 800Mhz/div, gpll0 */
- clk_rcg_set_rate_mnd(priv->base, &sdc_regs[slot], div, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, SDCC_CMD_RCGR(slot), div, 0, 0,
CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC_APPS_CBCR(slot));
return rate;
}
-static const struct bcr_regs uart2_regs = {
- .cfg_rcgr = BLSP1_UART2_APPS_CFG_RCGR,
- .cmd_rcgr = BLSP1_UART2_APPS_CMD_RCGR,
- .M = BLSP1_UART2_APPS_M,
- .N = BLSP1_UART2_APPS_N,
- .D = BLSP1_UART2_APPS_D,
-};
-
/* UART: 115200 */
int apq8016_clk_init_uart(phys_addr_t base)
{
/* Enable AHB clock */
clk_enable_vote_clk(base, &gcc_blsp1_ahb_clk);
/* 7372800 uart block clock @ GPLL0 */
- clk_rcg_set_rate_mnd(base, &uart2_regs, 1, 144, 15625,
+ clk_rcg_set_rate_mnd(base, BLSP1_UART2_APPS_CMD_RCGR, 1, 144, 15625,
CFG_CLK_SRC_GPLL0, 16);
/* Vote for gpll0 clock */
clk_enable_gpll0(base, &gpll0_vote_clk);
diff --git a/drivers/clk/qcom/clock-apq8096.c b/drivers/clk/qcom/clock-apq8096.c
index a4731613c5e0..479f9771a464 100644
--- a/drivers/clk/qcom/clock-apq8096.c
+++ b/drivers/clk/qcom/clock-apq8096.c
@@ -25,33 +25,17 @@
#define SDCC2_BCR (0x14000) /* block reset */
#define SDCC2_APPS_CBCR (0x14004) /* branch control */
#define SDCC2_AHB_CBCR (0x14008)
#define SDCC2_CMD_RCGR (0x14010)
-#define SDCC2_CFG_RCGR (0x14014)
-#define SDCC2_M (0x14018)
-#define SDCC2_N (0x1401C)
-#define SDCC2_D (0x14020)
#define BLSP2_AHB_CBCR (0x25004)
#define BLSP2_UART2_APPS_CBCR (0x29004)
#define BLSP2_UART2_APPS_CMD_RCGR (0x2900C)
-#define BLSP2_UART2_APPS_CFG_RCGR (0x29010)
-#define BLSP2_UART2_APPS_M (0x29014)
-#define BLSP2_UART2_APPS_N (0x29018)
-#define BLSP2_UART2_APPS_D (0x2901C)
/* GPLL0 clock control registers */
#define GPLL0_STATUS_ACTIVE BIT(30)
#define APCS_GPLL_ENA_VOTE_GPLL0 BIT(0)
-static const struct bcr_regs sdc_regs = {
- .cfg_rcgr = SDCC2_CFG_RCGR,
- .cmd_rcgr = SDCC2_CMD_RCGR,
- .M = SDCC2_M,
- .N = SDCC2_N,
- .D = SDCC2_D,
-};
-
static const struct pll_vote_clk gpll0_vote_clk = {
.status = GPLL0_STATUS,
.status_bit = GPLL0_STATUS_ACTIVE,
.ena_vote = APCS_GPLL_ENA_VOTE,
@@ -68,31 +52,23 @@ static int clk_init_sdc(struct msm_clk_priv *priv, uint
rate)
{
int div = 5;
clk_enable_cbc(priv->base + SDCC2_AHB_CBCR);
- clk_rcg_set_rate_mnd(priv->base, &sdc_regs, div, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, SDCC2_CMD_RCGR, div, 0, 0,
CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC2_APPS_CBCR);
return rate;
}
-static const struct bcr_regs uart2_regs = {
- .cfg_rcgr = BLSP2_UART2_APPS_CFG_RCGR,
- .cmd_rcgr = BLSP2_UART2_APPS_CMD_RCGR,
- .M = BLSP2_UART2_APPS_M,
- .N = BLSP2_UART2_APPS_N,
- .D = BLSP2_UART2_APPS_D,
-};
-
static int clk_init_uart(struct msm_clk_priv *priv)
{
/* Enable AHB clock */
clk_enable_vote_clk(priv->base, &gcc_blsp2_ahb_clk);
/* 7372800 uart block clock @ GPLL0 */
- clk_rcg_set_rate_mnd(priv->base, &uart2_regs, 1, 192, 15625,
+ clk_rcg_set_rate_mnd(priv->base, BLSP2_UART2_APPS_CMD_RCGR, 1, 192,
15625,
CFG_CLK_SRC_GPLL0, 16);
/* Vote for gpll0 clock */
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
diff --git a/drivers/clk/qcom/clock-qcom.c b/drivers/clk/qcom/clock-qcom.c
index 6303dcbf8461..05e5ab7d094b 100644
--- a/drivers/clk/qcom/clock-qcom.c
+++ b/drivers/clk/qcom/clock-qcom.c
@@ -103,9 +103,9 @@ void clk_bcr_update(phys_addr_t apps_cmd_rcgr)
/*
* root set rate for clocks with half integer and MND divider
* div should be pre-calculated ((div * 2) - 1)
*/
-void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
+void clk_rcg_set_rate_mnd(phys_addr_t base, uint32_t cmd_rcgr,
int div, int m, int n, int source, u8 mnd_width)
{
u32 cfg;
/* M value for MND divider. */
@@ -119,14 +119,14 @@ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct
bcr_regs *regs,
debug("m %#x n %#x d %#x div %#x mask %#x\n", m_val, n_val, d_val, div,
mask);
/* Program MND values */
- writel(m_val & mask, base + regs->M);
- writel(n_val & mask, base + regs->N);
- writel(d_val & mask, base + regs->D);
+ writel(m_val & mask, base + cmd_rcgr + RCG_M_REG);
+ writel(n_val & mask, base + cmd_rcgr + RCG_N_REG);
+ writel(d_val & mask, base + cmd_rcgr + RCG_D_REG);
/* setup src select and divider */
- cfg = readl(base + regs->cfg_rcgr);
+ cfg = readl(base + cmd_rcgr + RCG_CFG_REG);
cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK |
CFG_SRC_DIV_MASK);
cfg |= source & CFG_SRC_SEL_MASK; /* Select clock source */
@@ -135,22 +135,22 @@ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct
bcr_regs *regs,
if (n && n != m)
cfg |= CFG_MODE_DUAL_EDGE;
- writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */
+ writel(cfg, base + cmd_rcgr + RCG_CFG_REG); /* Write new clock
configuration */
/* Inform h/w to start using the new config. */
- clk_bcr_update(base + regs->cmd_rcgr);
+ clk_bcr_update(base + cmd_rcgr);
}
/* root set rate for clocks with half integer and mnd_width=0 */
-void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
+void clk_rcg_set_rate(phys_addr_t base, uint32_t cmd_rcgr, int div,
int source)
{
u32 cfg;
/* setup src select and divider */
- cfg = readl(base + regs->cfg_rcgr);
+ cfg = readl(base + cmd_rcgr + RCG_CFG_REG);
cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK);
cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */
/*
@@ -159,12 +159,12 @@ void clk_rcg_set_rate(phys_addr_t base, const struct
bcr_regs *regs, int div,
*/
if (div)
cfg |= (2 * div - 1) & CFG_SRC_DIV_MASK;
- writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */
+ writel(cfg, base + cmd_rcgr + RCG_CFG_REG); /* Write new clock
configuration */
/* Inform h/w to start using the new config. */
- clk_bcr_update(base + regs->cmd_rcgr);
+ clk_bcr_update(base + cmd_rcgr);
}
const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate)
{
diff --git a/drivers/clk/qcom/clock-qcom.h b/drivers/clk/qcom/clock-qcom.h
index 12a1eaec2b2e..a7f833a4b6dd 100644
--- a/drivers/clk/qcom/clock-qcom.h
+++ b/drivers/clk/qcom/clock-qcom.h
@@ -11,8 +11,13 @@
#define CFG_CLK_SRC_GPLL0 (1 << 8)
#define CFG_CLK_SRC_GPLL0_EVEN (6 << 8)
#define CFG_CLK_SRC_MASK (7 << 8)
+#define RCG_CFG_REG 0x4
+#define RCG_M_REG 0x8
+#define RCG_N_REG 0xc
+#define RCG_D_REG 0x10
+
struct pll_vote_clk {
uintptr_t status;
int status_bit;
uintptr_t ena_vote;
@@ -23,15 +28,8 @@ struct vote_clk {
uintptr_t cbcr_reg;
uintptr_t ena_vote;
int vote_bit;
};
-struct bcr_regs {
- uintptr_t cfg_rcgr;
- uintptr_t cmd_rcgr;
- uintptr_t M;
- uintptr_t N;
- uintptr_t D;
-};
struct freq_tbl {
uint freq;
uint src;
@@ -87,11 +85,11 @@ void clk_enable_gpll0(phys_addr_t base, const struct
pll_vote_clk *gpll0);
void clk_bcr_update(phys_addr_t apps_cmd_rgcr);
void clk_enable_cbc(phys_addr_t cbcr);
void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk);
const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate);
-void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
+void clk_rcg_set_rate_mnd(phys_addr_t base, uint32_t cmd_rcgr,
int div, int m, int n, int source, u8 mnd_width);
-void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
+void clk_rcg_set_rate(phys_addr_t base, uint32_t cmd_rcgr, int div,
int source);
static inline void qcom_gate_clk_en(const struct msm_clk_priv *priv, unsigned
long id)
{
diff --git a/drivers/clk/qcom/clock-qcs404.c b/drivers/clk/qcom/clock-qcs404.c
index 958312b88842..8a897a52bc00 100644
--- a/drivers/clk/qcom/clock-qcs404.c
+++ b/drivers/clk/qcom/clock-qcs404.c
@@ -27,37 +27,24 @@
/* Uart clock control registers */
#define BLSP1_UART2_BCR (0x3028)
#define BLSP1_UART2_APPS_CBCR (0x302C)
#define BLSP1_UART2_APPS_CMD_RCGR (0x3034)
-#define BLSP1_UART2_APPS_CFG_RCGR (0x3038)
-#define BLSP1_UART2_APPS_M (0x303C)
-#define BLSP1_UART2_APPS_N (0x3040)
-#define BLSP1_UART2_APPS_D (0x3044)
/* I2C controller clock control registerss */
#define BLSP1_QUP0_I2C_APPS_CBCR (0x6028)
#define BLSP1_QUP0_I2C_APPS_CMD_RCGR (0x602C)
-#define BLSP1_QUP0_I2C_APPS_CFG_RCGR (0x6030)
#define BLSP1_QUP1_I2C_APPS_CBCR (0x2008)
#define BLSP1_QUP1_I2C_APPS_CMD_RCGR (0x200C)
-#define BLSP1_QUP1_I2C_APPS_CFG_RCGR (0x2010)
#define BLSP1_QUP2_I2C_APPS_CBCR (0x3010)
#define BLSP1_QUP2_I2C_APPS_CMD_RCGR (0x3000)
-#define BLSP1_QUP2_I2C_APPS_CFG_RCGR (0x3004)
#define BLSP1_QUP3_I2C_APPS_CBCR (0x4020)
#define BLSP1_QUP3_I2C_APPS_CMD_RCGR (0x4000)
-#define BLSP1_QUP3_I2C_APPS_CFG_RCGR (0x4004)
#define BLSP1_QUP4_I2C_APPS_CBCR (0x5020)
#define BLSP1_QUP4_I2C_APPS_CMD_RCGR (0x5000)
-#define BLSP1_QUP4_I2C_APPS_CFG_RCGR (0x5004)
/* SD controller clock control registers */
#define SDCC_BCR(n) (((n) * 0x1000) + 0x41000)
-#define SDCC_CMD_RCGR(n) (((n) * 0x1000) + 0x41004)
-#define SDCC_CFG_RCGR(n) (((n) * 0x1000) + 0x41008)
-#define SDCC_M(n) (((n) * 0x1000) + 0x4100C)
-#define SDCC_N(n) (((n) * 0x1000) + 0x41010)
-#define SDCC_D(n) (((n) * 0x1000) + 0x41014)
+#define SDCC_CMD_RCGR(n) (((n + 1) * 0x1000) + 0x41004)
#define SDCC_APPS_CBCR(n) (((n) * 0x1000) + 0x41018)
#define SDCC_AHB_CBCR(n) (((n) * 0x1000) + 0x4101C)
/* USB-3.0 controller clock control registers */
@@ -69,12 +56,8 @@
#define USB30_MOCK_UTMI_CBCR (0x39014)
#define USB30_MOCK_UTMI_CMD_RCGR (0x3901C)
#define USB30_MOCK_UTMI_CFG_RCGR (0x39020)
#define USB30_MASTER_CMD_RCGR (0x39028)
-#define USB30_MASTER_CFG_RCGR (0x3902C)
-#define USB30_MASTER_M (0x39030)
-#define USB30_MASTER_N (0x39034)
-#define USB30_MASTER_D (0x39038)
#define USB2A_PHY_SLEEP_CBCR (0x4102C)
#define USB_HS_PHY_CFG_AHB_CBCR (0x41030)
/* ETH controller clock control registers */
@@ -82,14 +65,9 @@
#define ETH_RGMII_CBCR (0x4e008)
#define ETH_SLAVE_AHB_CBCR (0x4e00c)
#define ETH_AXI_CBCR (0x4e010)
#define EMAC_PTP_CMD_RCGR (0x4e014)
-#define EMAC_PTP_CFG_RCGR (0x4e018)
#define EMAC_CMD_RCGR (0x4e01c)
-#define EMAC_CFG_RCGR (0x4e020)
-#define EMAC_M (0x4e024)
-#define EMAC_N (0x4e028)
-#define EMAC_D (0x4e02c)
/* GPLL0 clock control registers */
#define GPLL0_STATUS_ACTIVE BIT(31)
@@ -102,24 +80,8 @@ static struct vote_clk gcc_blsp1_ahb_clk = {
.ena_vote = APCS_CLOCK_BRANCH_ENA_VOTE,
.vote_bit = BIT(10) | BIT(5) | BIT(4),
};
-static const struct bcr_regs uart2_regs = {
- .cfg_rcgr = BLSP1_UART2_APPS_CFG_RCGR,
- .cmd_rcgr = BLSP1_UART2_APPS_CMD_RCGR,
- .M = BLSP1_UART2_APPS_M,
- .N = BLSP1_UART2_APPS_N,
- .D = BLSP1_UART2_APPS_D,
-};
-
-static const struct bcr_regs sdc_regs = {
- .cfg_rcgr = SDCC_CFG_RCGR(1),
- .cmd_rcgr = SDCC_CMD_RCGR(1),
- .M = SDCC_M(1),
- .N = SDCC_N(1),
- .D = SDCC_D(1),
-};
-
static struct pll_vote_clk gpll0_vote_clk = {
.status = GPLL0_STATUS,
.status_bit = GPLL0_STATUS_ACTIVE,
.ena_vote = APCS_GPLL_ENA_VOTE,
@@ -132,92 +94,38 @@ static struct pll_vote_clk gpll1_vote_clk = {
.ena_vote = APCS_GPLL_ENA_VOTE,
.vote_bit = BIT(1),
};
-static const struct bcr_regs usb30_master_regs = {
- .cfg_rcgr = USB30_MASTER_CFG_RCGR,
- .cmd_rcgr = USB30_MASTER_CMD_RCGR,
- .M = USB30_MASTER_M,
- .N = USB30_MASTER_N,
- .D = USB30_MASTER_D,
-};
-
-static const struct bcr_regs emac_regs = {
- .cfg_rcgr = EMAC_CFG_RCGR,
- .cmd_rcgr = EMAC_CMD_RCGR,
- .M = EMAC_M,
- .N = EMAC_N,
- .D = EMAC_D,
-};
-
-static const struct bcr_regs emac_ptp_regs = {
- .cfg_rcgr = EMAC_PTP_CFG_RCGR,
- .cmd_rcgr = EMAC_PTP_CMD_RCGR,
- .M = EMAC_M,
- .N = EMAC_N,
- .D = EMAC_D,
-};
-
-static const struct bcr_regs blsp1_qup0_i2c_apps_regs = {
- .cmd_rcgr = BLSP1_QUP0_I2C_APPS_CMD_RCGR,
- .cfg_rcgr = BLSP1_QUP0_I2C_APPS_CFG_RCGR,
- /* mnd_width = 0 */
-};
-
-static const struct bcr_regs blsp1_qup1_i2c_apps_regs = {
- .cmd_rcgr = BLSP1_QUP1_I2C_APPS_CMD_RCGR,
- .cfg_rcgr = BLSP1_QUP1_I2C_APPS_CFG_RCGR,
- /* mnd_width = 0 */
-};
-
-static const struct bcr_regs blsp1_qup2_i2c_apps_regs = {
- .cmd_rcgr = BLSP1_QUP2_I2C_APPS_CMD_RCGR,
- .cfg_rcgr = BLSP1_QUP2_I2C_APPS_CFG_RCGR,
- /* mnd_width = 0 */
-};
-
-static const struct bcr_regs blsp1_qup3_i2c_apps_regs = {
- .cmd_rcgr = BLSP1_QUP3_I2C_APPS_CMD_RCGR,
- .cfg_rcgr = BLSP1_QUP3_I2C_APPS_CFG_RCGR,
- /* mnd_width = 0 */
-};
-
-static const struct bcr_regs blsp1_qup4_i2c_apps_regs = {
- .cmd_rcgr = BLSP1_QUP4_I2C_APPS_CMD_RCGR,
- .cfg_rcgr = BLSP1_QUP4_I2C_APPS_CFG_RCGR,
- /* mnd_width = 0 */
-};
-
static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate)
{
struct msm_clk_priv *priv = dev_get_priv(clk->dev);
switch (clk->id) {
case GCC_BLSP1_UART2_APPS_CLK:
/* UART: 1843200Hz for a fixed 115200 baudrate (19200000 *
(12/125)) */
- clk_rcg_set_rate_mnd(priv->base, &uart2_regs, 0, 12, 125,
+ clk_rcg_set_rate_mnd(priv->base, BLSP1_UART2_APPS_CMD_RCGR, 0,
12, 125,
CFG_CLK_SRC_CXO, 16);
clk_enable_cbc(priv->base + BLSP1_UART2_APPS_CBCR);
return 1843200;
case GCC_SDCC1_APPS_CLK:
/* SDCC1: 200MHz */
- clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 7, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, SDCC_CMD_RCGR(0), 7, 0, 0,
CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC_APPS_CBCR(1));
return rate;
case GCC_ETH_RGMII_CLK:
if (rate == 250000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, EMAC_CMD_RCGR, 3, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
else if (rate == 125000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 7, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, EMAC_CMD_RCGR, 7, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
else if (rate == 50000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 19, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, EMAC_CMD_RCGR, 19, 0,
0,
CFG_CLK_SRC_GPLL1, 8);
else if (rate == 5000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 1, 50,
+ clk_rcg_set_rate_mnd(priv->base, EMAC_CMD_RCGR, 3, 1,
50,
CFG_CLK_SRC_GPLL1, 8);
return rate;
}
@@ -236,9 +144,9 @@ static int qcs404_clk_enable(struct clk *clk)
switch (clk->id) {
case GCC_USB30_MASTER_CLK:
clk_enable_cbc(priv->base + USB30_MASTER_CBCR);
- clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 7, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, USB30_MASTER_CMD_RCGR, 7, 0, 0,
CFG_CLK_SRC_GPLL0, 8);
break;
case GCC_SYS_NOC_USB3_CLK:
clk_enable_cbc(priv->base + SYS_NOC_USB3_CBCR);
@@ -258,16 +166,16 @@ static int qcs404_clk_enable(struct clk *clk)
case GCC_ETH_PTP_CLK:
/* SPEED_1000: freq -> 250MHz */
clk_enable_cbc(priv->base + ETH_PTP_CBCR);
clk_enable_gpll0(priv->base, &gpll1_vote_clk);
- clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 3, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, EMAC_PTP_CMD_RCGR, 3, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
break;
case GCC_ETH_RGMII_CLK:
/* SPEED_1000: freq -> 250MHz */
clk_enable_cbc(priv->base + ETH_RGMII_CBCR);
clk_enable_gpll0(priv->base, &gpll1_vote_clk);
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, EMAC_CMD_RCGR, 3, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
break;
case GCC_ETH_SLAVE_AHB_CLK:
clk_enable_cbc(priv->base + ETH_SLAVE_AHB_CBCR);
@@ -279,29 +187,29 @@ static int qcs404_clk_enable(struct clk *clk)
clk_enable_vote_clk(priv->base, &gcc_blsp1_ahb_clk);
break;
case GCC_BLSP1_QUP0_I2C_APPS_CLK:
clk_enable_cbc(priv->base + BLSP1_QUP0_I2C_APPS_CBCR);
- clk_rcg_set_rate(priv->base, &blsp1_qup0_i2c_apps_regs, 0,
+ clk_rcg_set_rate(priv->base, BLSP1_QUP0_I2C_APPS_CMD_RCGR, 0,
CFG_CLK_SRC_CXO);
break;
case GCC_BLSP1_QUP1_I2C_APPS_CLK:
clk_enable_cbc(priv->base + BLSP1_QUP1_I2C_APPS_CBCR);
- clk_rcg_set_rate(priv->base, &blsp1_qup1_i2c_apps_regs, 0,
+ clk_rcg_set_rate(priv->base, BLSP1_QUP1_I2C_APPS_CMD_RCGR, 0,
CFG_CLK_SRC_CXO);
break;
case GCC_BLSP1_QUP2_I2C_APPS_CLK:
clk_enable_cbc(priv->base + BLSP1_QUP2_I2C_APPS_CBCR);
- clk_rcg_set_rate(priv->base, &blsp1_qup2_i2c_apps_regs, 0,
+ clk_rcg_set_rate(priv->base, BLSP1_QUP2_I2C_APPS_CMD_RCGR, 0,
CFG_CLK_SRC_CXO);
break;
case GCC_BLSP1_QUP3_I2C_APPS_CLK:
clk_enable_cbc(priv->base + BLSP1_QUP3_I2C_APPS_CBCR);
- clk_rcg_set_rate(priv->base, &blsp1_qup3_i2c_apps_regs, 0,
+ clk_rcg_set_rate(priv->base, BLSP1_QUP3_I2C_APPS_CMD_RCGR, 0,
CFG_CLK_SRC_CXO);
break;
case GCC_BLSP1_QUP4_I2C_APPS_CLK:
clk_enable_cbc(priv->base + BLSP1_QUP4_I2C_APPS_CBCR);
- clk_rcg_set_rate(priv->base, &blsp1_qup4_i2c_apps_regs, 0,
+ clk_rcg_set_rate(priv->base, BLSP1_QUP4_I2C_APPS_CMD_RCGR, 0,
CFG_CLK_SRC_CXO);
break;
case GCC_SDCC1_AHB_CLK:
clk_enable_cbc(priv->base + SDCC_AHB_CBCR(1));
diff --git a/drivers/clk/qcom/clock-sdm845.c b/drivers/clk/qcom/clock-sdm845.c
index babd83119e2c..ccb0cf245d33 100644
--- a/drivers/clk/qcom/clock-sdm845.c
+++ b/drivers/clk/qcom/clock-sdm845.c
@@ -18,15 +18,9 @@
#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include "clock-qcom.h"
-#define SE9_AHB_CBCR 0x25004
-#define SE9_UART_APPS_CBCR 0x29004
#define SE9_UART_APPS_CMD_RCGR 0x18148
-#define SE9_UART_APPS_CFG_RCGR 0x1814C
-#define SE9_UART_APPS_M 0x18150
-#define SE9_UART_APPS_N 0x18154
-#define SE9_UART_APPS_D 0x18158
static const struct freq_tbl ftbl_gcc_qupv3_wrap0_s0_clk_src[] = {
F(7372800, CFG_CLK_SRC_GPLL0_EVEN, 1, 384, 15625),
F(14745600, CFG_CLK_SRC_GPLL0_EVEN, 1, 768, 15625),
@@ -45,25 +39,17 @@ static const struct freq_tbl
ftbl_gcc_qupv3_wrap0_s0_clk_src[] = {
F(128000000, CFG_CLK_SRC_GPLL0, 1, 16, 75),
{ }
};
-static const struct bcr_regs uart2_regs = {
- .cfg_rcgr = SE9_UART_APPS_CFG_RCGR,
- .cmd_rcgr = SE9_UART_APPS_CMD_RCGR,
- .M = SE9_UART_APPS_M,
- .N = SE9_UART_APPS_N,
- .D = SE9_UART_APPS_D,
-};
-
static ulong sdm845_clk_set_rate(struct clk *clk, ulong rate)
{
struct msm_clk_priv *priv = dev_get_priv(clk->dev);
const struct freq_tbl *freq;
switch (clk->id) {
case GCC_QUPV3_WRAP1_S1_CLK: /* UART9 */
freq = qcom_find_freq(ftbl_gcc_qupv3_wrap0_s0_clk_src, rate);
- clk_rcg_set_rate_mnd(priv->base, &uart2_regs,
+ clk_rcg_set_rate_mnd(priv->base, SE9_UART_APPS_CMD_RCGR,
freq->pre_div, freq->m, freq->n,
freq->src, 16);
return freq->freq;
default:
return 0;
--
2.44.0
