This driver documents and handles setting up PWM on the D1.
Signed-off-by: John Watts <cont...@jookia.org>
---
drivers/pwm/Kconfig | 6 +
drivers/pwm/Makefile | 1 +
drivers/pwm/sunxi_pwm_d1.c | 542 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 549 insertions(+)
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 6e79868d0e..8c4c910ea7 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -112,6 +112,12 @@ config PWM_SUNXI
This PWM is found on H3, A64 and other Allwinner SoCs. It supports a
programmable period and duty cycle. A 16-bit counter is used.
+config PWM_SUNXI_D1
+ bool "Enable support for the Allwinner D1 Sunxi PWM"
+ depends on DM_PWM
+ help
+ This PWM is found on D1, T113-S3 and R329 SoCs.
+
config PWM_TI_EHRPWM
bool "Enable support for EHRPWM PWM"
depends on DM_PWM && ARCH_OMAP2PLUS
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index e4d10c8dc3..ea96e7159b 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -23,4 +23,5 @@ obj-$(CONFIG_PWM_SANDBOX) += sandbox_pwm.o
obj-$(CONFIG_PWM_SIFIVE) += pwm-sifive.o
obj-$(CONFIG_PWM_TEGRA) += tegra_pwm.o
obj-$(CONFIG_PWM_SUNXI) += sunxi_pwm.o
+obj-$(CONFIG_PWM_SUNXI_D1) += sunxi_pwm_d1.o
obj-$(CONFIG_PWM_TI_EHRPWM) += pwm-ti-ehrpwm.o
diff --git a/drivers/pwm/sunxi_pwm_d1.c b/drivers/pwm/sunxi_pwm_d1.c
new file mode 100644
index 0000000000..6c57bc6e85
--- /dev/null
+++ b/drivers/pwm/sunxi_pwm_d1.c
@@ -0,0 +1,542 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright 2022 Jookia <cont...@jookia.org>
+/*
+ * The Allwinner D1's PWM channels are 16-bit counters with up to
+ * 65537 cycles (yes, you read that correctly).
+ *
+ * Each channel must be programmed using three variables:
+ * - The entire cycle count (used for the period)
+ * - The active cycle count (the count of inactive cycles)
+ * - The polarity (specifies if the signal is active high or low)
+ * The cycle counts are at minimum 1 and at maximum 65536.
+ *
+ * The controller will output the number of entire cycles plus one
+ * extra, with any cycles after the active cycle output as active.
+ *
+ * Consider a PWM period of 128 nanoseconds and a cycle period of 32.
+ * Setting the entire cycle count to 3 and active cycle count to 4
+ * gives an output like so:
+ *
+ * - Cycle 1 runs 0 to 32 nanoseconds, inactive
+ * - Cycle 2 runs 32 to 64 nanoseconds, inactive
+ * - Cycle 3 runs 64 to 96 nanoseconds, inactive
+ * - Cycle 4 runs 96 to 128 nanoseconds, inactive
+ * - Cycle 5 is skipped but would run 128 to 160 nanoseconds, active
+ *
+ * If we set the entire count to 4, cycle 5 would run and we wouldn't be
+ * able to specify it as inactive as the active count only goes up to 4.
+ *
+ * In practice this means we want to set the entire cycle to be one less
+ * then the actual number of cycles we want, so we can set the number of
+ * active cycles to be up to maximum for a fully inactive signal.
+ *
+ * The PWM channels are paired and clocked together, resulting in a
+ * cycle time found using the following formula:
+ *
+ * PWM0_CYCLE_NS = 1000000000 / (BUS_CLOCK / COMMON_DIV / PWM0_PRESCALER_K)
+ * PWM1_CYCLE_NS = 1000000000 / (BUS_CLOCK / COMMON_DIV / PWM1_PRESCALER_K)
+ *
+ * This means both clocks should ideally be set at the same time and not
+ * impact each other too much.
+ */
+
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
+#include <clk.h>
+#include <reset.h>
+#include <pwm.h>
+#include <asm/io.h>
+
+/* PWM channel information */
+struct pwm_channel {
+ uint period_ns;
+ uint duty_ns;
+ bool polarity;
+ bool enable;
+ bool updated;
+};
+
+/* Timings found for a PWM channel */
+struct pwm_timings {
+ uint cycle_ns;
+ uint period_ns;
+ uint duty_ns;
+ uint clock_id;
+ uint common_div;
+ uint prescale_k;
+ uint entire_cycles;
+ uint active_cycles;
+ uint polarity;
+};
+
+/* Driver state */
+struct sunxi_pwm_d1_priv {
+ void *base;
+ struct clk *clk_bus;
+ struct clk *clk_srcs[3]; /* Last value must be NULL */
+ struct reset_ctl *reset;
+ int npwm;
+ struct pwm_channel *channels;
+};
+
+/* Divides a nanosecond value, rounding up for very low values */
+uint div_ns(uint ns, uint div)
+{
+ uint result = (ns / div);
+
+ /* If the number is less than 1000, round it to the nearest digit */
+ if (result < 1000)
+ result = (ns + (div - 1)) / div;
+
+ if (result < 1)
+ result = 1;
+
+ return result;
+}
+
+/* Checks if an error is relatively too large */
+int error_too_large(uint actual, uint target)
+{
+ /* For a target of zero we want zero */
+ if (target == 0)
+ return (actual == 0);
+
+ /* Don't overflow large numbers when we multiply by 100 */
+ while (actual > 1000) {
+ actual /= 100;
+ target /= 100;
+ }
+
+ int error_percent = (actual * 100) / target;
+
+ return (error_percent < 80 || 120 < error_percent);
+}
+
+/* Calculates the cycle nanoseconds from clock parameters */
+int get_cycle_ns(uint parent_hz, uint common_div, uint prescaler)
+{
+ return 1000000000 / ((parent_hz / common_div) / prescaler);
+}
+
+int find_channel_dividers(uint period_ns,
+ uint parent_hz,
+ struct pwm_timings *out)
+{
+ uint ideal_cycle_ns = div_ns(period_ns, 65536);
+ int common_div = out->common_div;
+ int prescaler = 1;
+ uint cycle_ns = 0;
+
+ for (;;) {
+ cycle_ns = get_cycle_ns(parent_hz, common_div, prescaler);
+ if (cycle_ns >= ideal_cycle_ns)
+ break;
+
+ prescaler *= 2;
+ if (prescaler > 256) {
+ if (common_div < 256) {
+ prescaler = 1;
+ common_div *= 2;
+ } else {
+ return -1;
+ }
+ }
+ }
+
+ out->common_div = common_div;
+ out->prescale_k = prescaler;
+ out->cycle_ns = cycle_ns;
+
+ return 0;
+}
+
+int find_channel_timings(const struct pwm_channel *in,
+ struct pwm_timings *out,
+ uint parent_hz)
+{
+ struct pwm_timings new = *out;
+
+ if (find_channel_dividers(in->period_ns, parent_hz, &new))
+ return -1;
+
+ new.entire_cycles = (in->period_ns / new.cycle_ns) - 1;
+ new.active_cycles = (in->duty_ns / new.cycle_ns);
+ new.period_ns = (new.entire_cycles + 1) * new.cycle_ns;
+ new.duty_ns = new.active_cycles * new.cycle_ns;
+ new.polarity = in->polarity;
+
+ if (error_too_large(new.period_ns, in->period_ns))
+ return -1;
+
+ if (in->duty_ns && error_too_large(new.duty_ns, in->duty_ns))
+ return -1;
+
+ *out = new;
+
+ return 0;
+}
+
+int find_pair_timings(const struct pwm_channel *channel0,
+ const struct pwm_channel *channel1,
+ struct pwm_timings *timings0,
+ struct pwm_timings *timings1,
+ int clock_hz)
+{
+ struct pwm_timings new0 = *timings0;
+ struct pwm_timings new1 = *timings1;
+ int err0 = 0;
+ int err1 = 0;
+
+ new0.common_div = 1;
+ new1.common_div = 1;
+
+ if (channel0->enable) {
+ err0 = find_channel_timings(channel0, &new0, clock_hz);
+ new1.common_div = new0.common_div;
+ }
+
+ if (channel1->enable) {
+ err1 = find_channel_timings(channel1, &new1, clock_hz);
+ new0 = *timings0;
+ new0.common_div = new1.common_div;
+ }
+
+ if (channel0->enable && channel1->enable) {
+ err0 = find_channel_timings(channel0, &new0, clock_hz);
+
+ if (new0.common_div != new1.common_div)
+ return -1;
+ }
+
+ if (err0 || err1)
+ return -1;
+
+ *timings0 = new0;
+ *timings1 = new1;
+
+ return 0;
+}
+
+int find_pair_timings_clocked(struct clk **clk_srcs,
+ const struct pwm_channel *channel0,
+ const struct pwm_channel *channel1,
+ struct pwm_timings *timings0,
+ struct pwm_timings *timings1)
+{
+ struct clk *clock = *clk_srcs;
+
+ for (int clock_id = 0; clock; clock = clk_srcs[++clock_id]) {
+ int clock_hz = clk_get_rate(clock);
+
+ if (clock_hz == 0 || IS_ERR_VALUE(clock_hz))
+ continue;
+
+ timings0->clock_id = clock_id;
+ timings1->clock_id = clock_id;
+
+ if (find_pair_timings(channel0, channel1,
+ timings0, timings1,
+ clock_hz))
+ continue;
+
+ return 0;
+ }
+
+ return -1;
+}
+
+#define PCGR(base) ((base) + 0x40)
+#define PCGR_CLK_GATE(channel) BIT(channel)
+
+#define PER(base) ((base) + 0x80)
+#define PER_ENABLE_PWM(channel) BIT(channel)
+
+#define PCCR(base, pair) ((base) + 0x20 + ((pair) * 2))
+#define PCCR_CLK_SRC(src) ((src) << 7)
+#define PCCR_CLK_SRC_MASK GENMASK(8, 7)
+#define PCCR_CLK_DIV_M(m) (m)
+#define PCCR_CLK_DIV_M_MASK GENMASK(3, 0)
+
+#define PCR(base, channel) ((base) + 0x100 + ((channel) * 0x20))
+#define PCR_PRESCAL_K(k) (k)
+#define PCR_PRESCAL_K_MASK GENMASK(7, 0)
+#define PCR_PWM_ACTIVE BIT(8)
+
+#define PPR(base, channel) ((base) + 0x104 + ((channel) * 0x20))
+#define PPR_ENTIRE_CYCLE(n) ((n) << 16)
+#define PPR_ENTIRE_CYCLE_MASK GENMASK(31, 16)
+#define PPR_ACT_CYCLE(n) (n)
+#define PPR_ACT_CYCLE_MASK GENMASK(15, 0)
+
+/* Like clrsetbits_le32 but with memory barriers */
+void clrsetreg(void *addr, u32 clear, u32 set)
+{
+ u32 val = readl(addr);
+
+ val &= ~clear;
+ val |= set;
+
+ writel(val, addr);
+}
+
+void disable_pair(void *base, int pair)
+{
+ u32 PER_clear = (PER_ENABLE_PWM(pair) | PER_ENABLE_PWM(pair + 1));
+ u32 PCGR_clear = (PCGR_CLK_GATE(pair) | PCGR_CLK_GATE(pair + 1));
+
+ clrsetreg(PER(base), PER_clear, 0);
+ clrsetreg(PCGR(base), PCGR_clear, 0);
+
+ log_debug("%s: pair %i, PCGR 0x%x, PER 0x%x\n",
+ __func__, pair, readl(PCGR(base)), readl(PER(base)));
+}
+
+void enable_pair(void *base, int pair, int clk_src, int clk_div)
+{
+ int div_m = fls(clk_div) - 1;
+
+ u32 PCGR_set = (PCGR_CLK_GATE(pair) | PCGR_CLK_GATE(pair + 1));
+ u32 PCCR_clear = (PCCR_CLK_SRC_MASK | PCCR_CLK_DIV_M_MASK);
+ u32 PCCR_set = (PCCR_CLK_SRC(clk_src) | PCCR_CLK_DIV_M(div_m));
+
+ clrsetreg(PCGR(base), 0, PCGR_set);
+ clrsetreg(PCCR(base, pair), PCCR_clear, PCCR_set);
+
+ log_debug("%s: pair %i, clk_src %i, div_m %i, PCCR 0x%x\n",
+ __func__, pair, clk_src, div_m, readl(PCCR(base, pair)));
+}
+
+void enable_channel(void *base, int channel, struct pwm_timings *timings)
+{
+ u32 pwm_active = (timings->polarity) ? 0 : PCR_PWM_ACTIVE;
+ u32 prescale = (timings->prescale_k - 1);
+ u32 entire_cycles = timings->entire_cycles;
+ u32 active_cycles = timings->active_cycles;
+
+ u32 PCR_clear = (PCR_PRESCAL_K_MASK | PCR_PWM_ACTIVE);
+ u32 PCR_set = (PCR_PRESCAL_K(prescale) | pwm_active);
+ u32 PPR_clear = (PPR_ENTIRE_CYCLE_MASK | PPR_ACT_CYCLE_MASK);
+ u32 PPR_set = (PPR_ENTIRE_CYCLE(entire_cycles) |
PPR_ACT_CYCLE(active_cycles));
+ u32 PER_set = PER_ENABLE_PWM(channel);
+
+ clrsetreg(PCR(base, channel), PCR_clear, PCR_set);
+ clrsetreg(PPR(base, channel), PPR_clear, PPR_set);
+ clrsetreg(PER(base), 0, PER_set);
+
+ log_debug("%s: channel %u, clock_id %u, period_ns %u, duty_ns %u,
common_div %u, prescale_k %u, entire_cycles %u, active_cycles %u, polarity %u,
PCGR 0x%x, PCR 0x%x, PPR 0x%x, PER 0x%x\n",
+ __func__, channel, timings->clock_id, timings->period_ns,
+ timings->duty_ns, timings->common_div, timings->prescale_k,
+ timings->entire_cycles, timings->active_cycles,
+ timings->polarity, readl(PCGR(base)),
+ readl(PCR(base, channel)), readl(PPR(base, channel)),
+ readl(PER(base)));
+}
+
+int update_channel_pair(struct sunxi_pwm_d1_priv *priv, int pair)
+{
+ struct pwm_timings timings0 = {0};
+ struct pwm_timings timings1 = {0};
+ struct pwm_channel *channel0 = &priv->channels[pair + 0];
+ struct pwm_channel *channel1 = &priv->channels[pair + 1];
+ void *base = priv->base;
+
+ if (channel0->updated && channel1->updated)
+ return 0;
+
+ disable_pair(base, pair);
+
+ if (find_pair_timings_clocked(priv->clk_srcs, channel0, channel1,
&timings0, &timings1))
+ return -1;
+
+ if (channel0->enable || channel1->enable)
+ enable_pair(base, pair, timings0.clock_id, timings0.common_div);
+
+ if (channel0->enable)
+ enable_channel(base, pair + 0, &timings0);
+
+ if (channel1->enable)
+ enable_channel(base, pair + 1, &timings1);
+
+ channel0->updated = true;
+ channel1->updated = true;
+
+ return 0;
+}
+
+static int update_channels(struct udevice *dev)
+{
+ struct sunxi_pwm_d1_priv *priv = dev_get_priv(dev);
+ int i;
+
+ for (i = 0; i < priv->npwm; i += 2) {
+ int ret = update_channel_pair(priv, i);
+
+ if (ret != 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int sunxi_pwm_d1_set_invert(struct udevice *dev, uint channel_num,
+ bool polarity)
+{
+ struct sunxi_pwm_d1_priv *priv = dev_get_priv(dev);
+ struct pwm_channel *channel;
+
+ if (channel_num >= priv->npwm)
+ return -EINVAL;
+
+ channel = &priv->channels[channel_num];
+ channel->updated = (channel->polarity == polarity);
+ channel->polarity = polarity;
+
+ return update_channels(dev);
+}
+
+static int sunxi_pwm_d1_set_config(struct udevice *dev, uint channel_num,
+ uint period_ns, uint duty_ns)
+{
+ struct sunxi_pwm_d1_priv *priv = dev_get_priv(dev);
+ struct pwm_channel *channel;
+
+ if (channel_num >= priv->npwm)
+ return -EINVAL;
+
+ channel = &priv->channels[channel_num];
+ channel->updated = (channel->period_ns == period_ns && channel->duty_ns
== duty_ns);
+ channel->period_ns = period_ns;
+ channel->duty_ns = duty_ns;
+
+ return update_channels(dev);
+}
+
+static int sunxi_pwm_d1_set_enable(struct udevice *dev, uint channel_num, bool
enable)
+{
+ struct sunxi_pwm_d1_priv *priv = dev_get_priv(dev);
+ struct pwm_channel *channel;
+
+ if (channel_num >= priv->npwm)
+ return -EINVAL;
+
+ channel = &priv->channels[channel_num];
+ channel->updated = (channel->enable == enable);
+ channel->enable = enable;
+
+ return update_channels(dev);
+}
+
+static int sunxi_pwm_d1_of_to_plat(struct udevice *dev)
+{
+ struct sunxi_pwm_d1_priv *priv = dev_get_priv(dev);
+ struct clk *clk_hosc;
+ struct clk *clk_apb0;
+ int ret;
+
+ priv->base = dev_read_addr_ptr(dev);
+
+ if (!priv->base) {
+ dev_err(dev, "Unset device tree offset?\n");
+ return -EINVAL;
+ }
+
+ priv->clk_bus = devm_clk_get(dev, "bus");
+
+ if (IS_ERR(priv->clk_bus)) {
+ dev_err(dev, "failed to get bus clock: %ld",
+ PTR_ERR(priv->clk_bus));
+ return PTR_ERR(priv->clk_bus);
+ }
+
+ ret = clk_enable(priv->clk_bus);
+
+ if (ret) {
+ dev_err(dev, "failed to enable bus clk: %d", ret);
+ return ret;
+ }
+
+ clk_hosc = devm_clk_get(dev, "hosc");
+
+ if (IS_ERR(clk_hosc)) {
+ dev_err(dev, "failed to get hosc clock: %ld",
+ PTR_ERR(clk_hosc));
+ return PTR_ERR(clk_hosc);
+ }
+
+ clk_apb0 = devm_clk_get(dev, "apb0");
+
+ if (IS_ERR(clk_apb0)) {
+ dev_err(dev, "failed to get apb0 clock: %ld",
+ PTR_ERR(clk_apb0));
+ return PTR_ERR(clk_apb0);
+ }
+
+ priv->clk_srcs[0] = clk_hosc;
+ priv->clk_srcs[1] = clk_apb0;
+ priv->clk_srcs[2] = NULL;
+
+ priv->reset = devm_reset_control_get(dev, NULL);
+
+ if (IS_ERR(priv->reset)) {
+ dev_err(dev, "failed to get reset: %ld",
+ PTR_ERR(priv->reset));
+ return PTR_ERR(priv->reset);
+ }
+
+ priv->npwm = 8;
+ ret = dev_read_u32(dev, "allwinner,pwm-channels", &priv->npwm);
+
+ if (ret < 0 && ret != -EINVAL) {
+ dev_err(dev, "failed to read allwinner,pwm-channels: %d",
+ ret);
+ return ret;
+ }
+
+ priv->channels = devm_kzalloc(dev,
+ sizeof(struct pwm_channel) * priv->npwm,
+ GFP_KERNEL);
+
+ if (!priv->channels) {
+ dev_err(dev, "failed to read allocate pwm channels");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int sunxi_pwm_d1_probe(struct udevice *dev)
+{
+ struct sunxi_pwm_d1_priv *priv = dev_get_priv(dev);
+ int ret;
+
+ ret = reset_deassert(priv->reset);
+
+ if (ret < 0) {
+ dev_err(dev, "failed to deassert reset: %d", ret);
+ return ret;
+ }
+
+ return update_channels(dev);
+}
+
+static const struct pwm_ops sunxi_pwm_d1_ops = {
+ .set_invert = sunxi_pwm_d1_set_invert,
+ .set_config = sunxi_pwm_d1_set_config,
+ .set_enable = sunxi_pwm_d1_set_enable,
+};
+
+static const struct udevice_id sunxi_pwm_d1_ids[] = {
+ { .compatible = "allwinner,sun20i-d1-pwm" },
+ { }
+};
+
+U_BOOT_DRIVER(sunxi_pwm_d1) = {
+ .name = "sunxi_pwm_d1",
+ .id = UCLASS_PWM,
+ .of_match = sunxi_pwm_d1_ids,
+ .ops = &sunxi_pwm_d1_ops,
+ .of_to_plat = sunxi_pwm_d1_of_to_plat,
+ .probe = sunxi_pwm_d1_probe,
+ .priv_auto = sizeof(struct sunxi_pwm_d1_priv),
+};
--
2.45.1
