This adds TCPM framework in preparation for fusb302 support, which can
handle USB power delivery messages. This is needed to solve issues with
devices, that are running from a USB-C port supporting USB-PD, but not
having a battery.
Such a device currently boots to the kernel without interacting with
the power-supply at all. If there are no USB-PD message replies within
5 seconds, the power-supply assumes the peripheral is not capable of
USB-PD. It usually takes more than 5 seconds for the system to reach
the kernel and probe the I2C based fusb302 chip driver. Thus the
system always runs into this state. The power-supply's solution to
fix this error state is a hard reset, which involves removing the
power from VBUS. Boards without a battery (or huge capacitors) will
reset at this point resulting in a boot loop.
This imports the TCPM framework from the kernel. The porting has
originally been done by Rockchip using hardware timers and the Linux
kernel's TCPM code from some years ago.
I had a look at upgrading to the latest TCPM kernel code, but that
beast became a lot more complex due to adding more USB-C features.
I believe these features are not needed in U-Boot and with multiple
kthreads and hrtimers being involved it is non-trivial to port them.
Instead I worked on stripping down features from the Rockchip port
to an even more basic level. Also the TCPM code has been reworked
to avoid complete use of any timers (Rockchip used SoC specific
hardware timers + IRQ to implement delayed work mechanism). Instead
the delayed state changes are handled directly from the poll loop.
Note, that (in contrast to the original Rockchip port) the state
machine has the same hard reset quirk, that the kernel has - i.e.
it avoids disabling the CC pin resistors for devices that are not
self-powered. Without that quirk, the Radxa Rock 5B will not just
end up doing a machine reset when a hard reset is triggered, but will
not even recover, because the CPU will loose power and the FUSB302
will keep this state because of leak voltage arriving through the RX
serial pin (assuming a serial adapter is connected).
This also includes a 'tcpm' command, which can be used to get
information about the current state and the negotiated voltage
and current.
Co-developed-by: Wang Jie <dave.w...@rock-chips.com>
Signed-off-by: Wang Jie <dave.w...@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reic...@collabora.com>
---
Makefile | 1 +
cmd/Kconfig | 7 +
cmd/Makefile | 1 +
cmd/tcpm.c | 117 ++
drivers/usb/Kconfig | 2 +
drivers/usb/tcpm/Kconfig | 8 +
drivers/usb/tcpm/Makefile | 3 +
drivers/usb/tcpm/tcpm.c | 2406 +++++++++++++++++++++++++++++++++++++
include/dm/uclass-id.h | 1 +
include/usb/pd.h | 516 ++++++++
include/usb/tcpm.h | 116 ++
11 files changed, 3178 insertions(+)
create mode 100644 cmd/tcpm.c
create mode 100644 drivers/usb/tcpm/Kconfig
create mode 100644 drivers/usb/tcpm/Makefile
create mode 100644 drivers/usb/tcpm/tcpm.c
create mode 100644 include/usb/pd.h
create mode 100644 include/usb/tcpm.h
diff --git a/Makefile b/Makefile
index 79b28c2d81fd..74e6f3b416f0 100644
--- a/Makefile
+++ b/Makefile
@@ -879,6 +879,7 @@ libs-y += drivers/usb/musb/
libs-y += drivers/usb/musb-new/
libs-y += drivers/usb/isp1760/
libs-y += drivers/usb/phy/
+libs-y += drivers/usb/tcpm/
libs-y += drivers/usb/ulpi/
ifdef CONFIG_POST
libs-y += post/
diff --git a/cmd/Kconfig b/cmd/Kconfig
index b026439c7731..a27da5467842 100644
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
@@ -221,6 +221,13 @@ config CMD_REGINFO
help
Register dump
+config CMD_TCPM
+ bool "tcpm"
+ depends on TYPEC_TCPM
+ help
+ Show voltage and current negotiated via USB PD as well as the
+ current state of the Type C Port Manager (TCPM) state machine.
+
config CMD_TLV_EEPROM
bool "tlv_eeprom"
depends on I2C_EEPROM
diff --git a/cmd/Makefile b/cmd/Makefile
index 87133cc27a8a..bd0b23ef1013 100644
--- a/cmd/Makefile
+++ b/cmd/Makefile
@@ -172,6 +172,7 @@ obj-$(CONFIG_CMD_SMBIOS) += smbios.o
obj-$(CONFIG_CMD_SMC) += smccc.o
obj-$(CONFIG_CMD_SYSBOOT) += sysboot.o
obj-$(CONFIG_CMD_STACKPROTECTOR_TEST) += stackprot_test.o
+obj-$(CONFIG_CMD_TCPM) += tcpm.o
obj-$(CONFIG_CMD_TEMPERATURE) += temperature.o
obj-$(CONFIG_CMD_TERMINAL) += terminal.o
obj-$(CONFIG_CMD_TIME) += time.o
diff --git a/cmd/tcpm.c b/cmd/tcpm.c
new file mode 100644
index 000000000000..fa16a29877f5
--- /dev/null
+++ b/cmd/tcpm.c
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2024 Collabora
+ */
+
+#include <command.h>
+#include <errno.h>
+#include <dm.h>
+#include <dm/uclass-internal.h>
+#include <usb/tcpm.h>
+
+#define LIMIT_DEV 32
+#define LIMIT_PARENT 20
+
+static struct udevice *currdev;
+
+static int failure(int ret)
+{
+ printf("Error: %d (%s)\n", ret, errno_str(ret));
+
+ return CMD_RET_FAILURE;
+}
+
+static int do_dev(struct cmd_tbl *cmdtp, int flag, int argc, char *const
argv[])
+{
+ char *name;
+ int ret = -ENODEV;
+
+ switch (argc) {
+ case 2:
+ name = argv[1];
+ ret = tcpm_get(name, &currdev);
+ if (ret) {
+ printf("Can't get TCPM: %s!\n", name);
+ return failure(ret);
+ }
+ case 1:
+ if (!currdev) {
+ printf("TCPM device is not set!\n\n");
+ return CMD_RET_USAGE;
+ }
+
+ printf("dev: %d @ %s\n", dev_seq(currdev), currdev->name);
+ }
+
+ return CMD_RET_SUCCESS;
+}
+
+static int do_list(struct cmd_tbl *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ struct udevice *dev;
+ int ret, err = 0;
+
+ printf("| %-*.*s| %-*.*s| %s @ %s\n",
+ LIMIT_DEV, LIMIT_DEV, "Name",
+ LIMIT_PARENT, LIMIT_PARENT, "Parent name",
+ "Parent uclass", "seq");
+
+ for (ret = uclass_first_device_check(UCLASS_TCPM, &dev); dev;
+ ret = uclass_next_device_check(&dev)) {
+ if (ret)
+ err = ret;
+
+ printf("| %-*.*s| %-*.*s| %s @ %d | status: %i\n",
+ LIMIT_DEV, LIMIT_DEV, dev->name,
+ LIMIT_PARENT, LIMIT_PARENT, dev->parent->name,
+ dev_get_uclass_name(dev->parent), dev_seq(dev->parent),
+ ret);
+ }
+
+ if (err)
+ return CMD_RET_FAILURE;
+
+ return CMD_RET_SUCCESS;
+}
+
+static int do_info(struct cmd_tbl *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ if (!currdev) {
+ printf("First, set the TCPM device!\n");
+ return CMD_RET_USAGE;
+ }
+
+ return tcpm_print_info(currdev);
+}
+
+static struct cmd_tbl subcmd[] = {
+ U_BOOT_CMD_MKENT(dev, 2, 1, do_dev, "", ""),
+ U_BOOT_CMD_MKENT(list, 1, 1, do_list, "", ""),
+ U_BOOT_CMD_MKENT(info, 1, 1, do_info, "", ""),
+};
+
+static int do_tcpm(struct cmd_tbl *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ struct cmd_tbl *cmd;
+
+ argc--;
+ argv++;
+
+ cmd = find_cmd_tbl(argv[0], subcmd, ARRAY_SIZE(subcmd));
+ if (!cmd || argc > cmd->maxargs)
+ return CMD_RET_USAGE;
+
+ return cmd->cmd(cmdtp, flag, argc, argv);
+}
+
+ /**************************************************/
+
+U_BOOT_CMD(tcpm, CONFIG_SYS_MAXARGS, 1, do_tcpm,
+ "TCPM sub-system",
+ "list - list TCPM devices\n"
+ "tcpm dev [name] - show or [set] operating TCPM device\n"
+ "tcpm info - dump information\n"
+);
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index a972d87c7ad4..985d3a9ef7e6 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -85,6 +85,8 @@ source "drivers/usb/emul/Kconfig"
source "drivers/usb/phy/Kconfig"
+source "drivers/usb/tcpm/Kconfig"
+
source "drivers/usb/ulpi/Kconfig"
if USB_HOST
diff --git a/drivers/usb/tcpm/Kconfig b/drivers/usb/tcpm/Kconfig
new file mode 100644
index 000000000000..55bf8e202b90
--- /dev/null
+++ b/drivers/usb/tcpm/Kconfig
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config TYPEC_TCPM
+ tristate "USB Type-C Port Controller Manager"
+ depends on DM
+ help
+ The Type-C Port Controller Manager provides a USB PD and USB Type-C
+ state machine for use with Type-C Port Controllers.
diff --git a/drivers/usb/tcpm/Makefile b/drivers/usb/tcpm/Makefile
new file mode 100644
index 000000000000..f3815b7e466e
--- /dev/null
+++ b/drivers/usb/tcpm/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_TYPEC_TCPM) += tcpm.o
diff --git a/drivers/usb/tcpm/tcpm.c b/drivers/usb/tcpm/tcpm.c
new file mode 100644
index 000000000000..a2a228557f4a
--- /dev/null
+++ b/drivers/usb/tcpm/tcpm.c
@@ -0,0 +1,2406 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2015-2017 Google, Inc
+ *
+ * USB Power Delivery protocol stack.
+ */
+
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <dm/device-internal.h>
+#include <dm/devres.h>
+#include <linux/compat.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <time.h>
+#include <usb/tcpm.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define FOREACH_STATE(S) \
+ S(INVALID_STATE), \
+ S(TOGGLING), \
+ S(SRC_UNATTACHED), \
+ S(SRC_ATTACH_WAIT), \
+ S(SRC_ATTACHED), \
+ S(SRC_STARTUP), \
+ S(SRC_SEND_CAPABILITIES), \
+ S(SRC_SEND_CAPABILITIES_TIMEOUT), \
+ S(SRC_NEGOTIATE_CAPABILITIES), \
+ S(SRC_TRANSITION_SUPPLY), \
+ S(SRC_READY), \
+ S(SRC_WAIT_NEW_CAPABILITIES), \
+ \
+ S(SNK_UNATTACHED), \
+ S(SNK_ATTACH_WAIT), \
+ S(SNK_DEBOUNCED), \
+ S(SNK_ATTACHED), \
+ S(SNK_STARTUP), \
+ S(SNK_DISCOVERY), \
+ S(SNK_DISCOVERY_DEBOUNCE), \
+ S(SNK_DISCOVERY_DEBOUNCE_DONE), \
+ S(SNK_WAIT_CAPABILITIES), \
+ S(SNK_NEGOTIATE_CAPABILITIES), \
+ S(SNK_TRANSITION_SINK), \
+ S(SNK_TRANSITION_SINK_VBUS), \
+ S(SNK_READY), \
+ \
+ S(HARD_RESET_SEND), \
+ S(HARD_RESET_START), \
+ S(SRC_HARD_RESET_VBUS_OFF), \
+ S(SRC_HARD_RESET_VBUS_ON), \
+ S(SNK_HARD_RESET_SINK_OFF), \
+ S(SNK_HARD_RESET_WAIT_VBUS), \
+ S(SNK_HARD_RESET_SINK_ON), \
+ \
+ S(SOFT_RESET), \
+ S(SOFT_RESET_SEND), \
+ \
+ S(DR_SWAP_ACCEPT), \
+ S(DR_SWAP_CHANGE_DR), \
+ \
+ S(ERROR_RECOVERY), \
+ S(PORT_RESET), \
+ S(PORT_RESET_WAIT_OFF)
+
+#define GENERATE_ENUM(e) e
+#define GENERATE_STRING(s) #s
+#define TCPM_POLL_EVENT_TIME_OUT 2000
+
+enum tcpm_state {
+ FOREACH_STATE(GENERATE_ENUM)
+};
+
+static const char * const tcpm_states[] = {
+ FOREACH_STATE(GENERATE_STRING)
+};
+
+enum pd_msg_request {
+ PD_MSG_NONE = 0,
+ PD_MSG_CTRL_REJECT,
+ PD_MSG_CTRL_WAIT,
+ PD_MSG_CTRL_NOT_SUPP,
+ PD_MSG_DATA_SINK_CAP,
+ PD_MSG_DATA_SOURCE_CAP,
+};
+
+struct tcpm_port {
+ struct udevice *dev;
+ enum typec_port_type typec_type;
+ int typec_prefer_role;
+ struct tcpc_dev *tcpc;
+
+ enum typec_role vconn_role;
+ enum typec_role pwr_role;
+ enum typec_data_role data_role;
+
+ struct typec_partner *partner;
+
+ enum typec_cc_status cc_req;
+ enum typec_cc_status cc1;
+ enum typec_cc_status cc2;
+ enum typec_cc_polarity polarity;
+
+ bool attached;
+ bool connected;
+ int poll_event_cnt;
+ enum typec_port_type port_type;
+
+ /*
+ * Set to true when vbus is greater than VSAFE5V min.
+ * Set to false when vbus falls below vSinkDisconnect max threshold.
+ */
+ bool vbus_present;
+
+ /*
+ * Set to true when vbus is less than VSAFE0V max.
+ * Set to false when vbus is greater than VSAFE0V max.
+ */
+ bool vbus_vsafe0v;
+
+ bool vbus_never_low;
+ bool vbus_source;
+ bool vbus_charge;
+
+ int try_role;
+
+ enum pd_msg_request queued_message;
+
+ enum tcpm_state enter_state;
+ enum tcpm_state prev_state;
+ enum tcpm_state state;
+ enum tcpm_state delayed_state;
+ unsigned long delay_ms;
+
+ bool state_machine_running;
+
+ bool tx_complete;
+ enum tcpm_transmit_status tx_status;
+
+ unsigned int negotiated_rev;
+ unsigned int message_id;
+ unsigned int caps_count;
+ unsigned int hard_reset_count;
+ bool pd_capable;
+ bool explicit_contract;
+ unsigned int rx_msgid;
+
+ /* Partner capabilities/requests */
+ u32 sink_request;
+ u32 source_caps[PDO_MAX_OBJECTS];
+ unsigned int nr_source_caps;
+ u32 sink_caps[PDO_MAX_OBJECTS];
+ unsigned int nr_sink_caps;
+
+ /*
+ * whether to wait for the Type-C device to send the DR_SWAP Message
flag
+ * For Type-C device with Dual-Role Power and Dual-Role Data, the port
side
+ * is used as sink + ufp, then the tcpm framework needs to wait for
Type-C
+ * device to initiate DR_swap Message.
+ */
+ bool wait_dr_swap_message;
+
+ /* Local capabilities */
+ u32 src_pdo[PDO_MAX_OBJECTS];
+ unsigned int nr_src_pdo;
+ u32 snk_pdo[PDO_MAX_OBJECTS];
+ unsigned int nr_snk_pdo;
+
+ unsigned int operating_snk_mw;
+ bool update_sink_caps;
+
+ /* Requested current / voltage to the port partner */
+ u32 req_current_limit;
+ u32 req_supply_voltage;
+ /* Actual current / voltage limit of the local port */
+ u32 current_limit;
+ u32 supply_voltage;
+
+ /* port belongs to a self powered device */
+ bool self_powered;
+
+ unsigned long delay_target;
+};
+
+struct pd_rx_event {
+ struct tcpm_port *port;
+ struct pd_message msg;
+};
+
+static const char * const pd_rev[] = {
+ [PD_REV10] = "rev1",
+ [PD_REV20] = "rev2",
+ [PD_REV30] = "rev3",
+};
+
+static bool tcpm_cc_is_sink(enum typec_cc_status cc)
+{
+ return ((cc) == TYPEC_CC_RP_DEF ||
+ (cc) == TYPEC_CC_RP_1_5 ||
+ (cc) == TYPEC_CC_RP_3_0);
+}
+
+static bool tcpm_port_is_sink(struct tcpm_port *port)
+{
+ return ((tcpm_cc_is_sink(port->cc1) &&
+ !tcpm_cc_is_sink(port->cc2)) ||
+ (tcpm_cc_is_sink(port->cc2) &&
+ !tcpm_cc_is_sink(port->cc1)));
+}
+
+static bool tcpm_cc_is_source(enum typec_cc_status cc)
+{
+ return ((cc) == TYPEC_CC_RD);
+}
+
+static bool tcpm_port_is_source(struct tcpm_port *port)
+{
+ return ((tcpm_cc_is_source((port)->cc1) &&
+ !tcpm_cc_is_source((port)->cc2)) ||
+ (tcpm_cc_is_source((port)->cc2) &&
+ !tcpm_cc_is_source((port)->cc1)));
+}
+
+static bool tcpm_try_src(struct tcpm_port *port)
+{
+ return ((port)->try_role == TYPEC_SOURCE &&
+ (port)->port_type == TYPEC_PORT_DRP);
+}
+
+static enum tcpm_state tcpm_default_state(struct tcpm_port *port)
+{
+ if (port->port_type == TYPEC_PORT_DRP) {
+ if (port->try_role == TYPEC_SINK)
+ return SNK_UNATTACHED;
+ else if (port->try_role == TYPEC_SOURCE)
+ return SRC_UNATTACHED;
+ } else if (port->port_type == TYPEC_PORT_SNK) {
+ return SNK_UNATTACHED;
+ }
+ return SRC_UNATTACHED;
+}
+
+static bool tcpm_port_is_disconnected(struct tcpm_port *port)
+{
+ return (!port->attached && port->cc1 == TYPEC_CC_OPEN &&
+ port->cc2 == TYPEC_CC_OPEN) ||
+ (port->attached && ((port->polarity == TYPEC_POLARITY_CC1 &&
+ port->cc1 == TYPEC_CC_OPEN) ||
+ (port->polarity == TYPEC_POLARITY_CC2 &&
+ port->cc2 == TYPEC_CC_OPEN)));
+}
+
+static void tcpm_set_cc(struct tcpm_port *port, enum typec_cc_status cc)
+{
+ dev_dbg(port->dev, "TCPM: set cc = %d\n", cc);
+ port->cc_req = cc;
+ port->tcpc->set_cc(port->tcpc, cc);
+}
+
+/*
+ * Determine RP value to set based on maximum current supported
+ * by a port if configured as source.
+ * Returns CC value to report to link partner.
+ */
+static enum typec_cc_status tcpm_rp_cc(struct tcpm_port *port)
+{
+ const u32 *src_pdo = port->src_pdo;
+ int nr_pdo = port->nr_src_pdo;
+ int i;
+
+ /*
+ * Search for first entry with matching voltage.
+ * It should report the maximum supported current.
+ */
+ for (i = 0; i < nr_pdo; i++) {
+ const u32 pdo = src_pdo[i];
+
+ if (pdo_type(pdo) == PDO_TYPE_FIXED &&
+ pdo_fixed_voltage(pdo) == 5000) {
+ unsigned int curr = pdo_max_current(pdo);
+
+ if (curr >= 3000)
+ return TYPEC_CC_RP_3_0;
+ else if (curr >= 1500)
+ return TYPEC_CC_RP_1_5;
+ return TYPEC_CC_RP_DEF;
+ }
+ }
+
+ return TYPEC_CC_RP_DEF;
+}
+
+static void tcpm_check_and_run_delayed_work(struct tcpm_port *port);
+
+static int tcpm_pd_transmit(struct tcpm_port *port,
+ enum tcpm_transmit_type type,
+ const struct pd_message *msg)
+{
+ int ret;
+ int timeout = PD_T_TCPC_TX_TIMEOUT;
+
+ if (msg)
+ dev_dbg(port->dev, "TCPM: PD TX, header: %#x\n",
+ le16_to_cpu(msg->header));
+ else
+ dev_dbg(port->dev, "TCPM: PD TX, type: %#x\n", type);
+
+ port->tx_complete = false;
+ ret = port->tcpc->pd_transmit(port->tcpc, type, msg,
port->negotiated_rev);
+ if (ret < 0)
+ return ret;
+
+ while ((timeout > 0) && (!port->tx_complete)) {
+ port->tcpc->poll_event(port->tcpc);
+ udelay(1000);
+ timeout--;
+ tcpm_check_and_run_delayed_work(port);
+ }
+
+ if (!timeout) {
+ dev_err(port->dev, "TCPM: PD transmit data timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ switch (port->tx_status) {
+ case TCPC_TX_SUCCESS:
+ port->message_id = (port->message_id + 1) & PD_HEADER_ID_MASK;
+ break;
+ case TCPC_TX_DISCARDED:
+ ret = -EAGAIN;
+ break;
+ case TCPC_TX_FAILED:
+ default:
+ ret = -EIO;
+ break;
+ }
+
+ return ret;
+}
+
+void tcpm_pd_transmit_complete(struct tcpm_port *port,
+ enum tcpm_transmit_status status)
+{
+ dev_dbg(port->dev, "TCPM: PD TX complete, status: %u\n", status);
+ port->poll_event_cnt = 0;
+ port->tx_status = status;
+ port->tx_complete = true;
+}
+EXPORT_SYMBOL_GPL(tcpm_pd_transmit_complete);
+
+static int tcpm_set_polarity(struct tcpm_port *port,
+ enum typec_cc_polarity polarity)
+{
+ int ret;
+
+ dev_dbg(port->dev, "TCPM: set polarity = %d\n", polarity);
+
+ ret = port->tcpc->set_polarity(port->tcpc, polarity);
+ if (ret < 0)
+ return ret;
+
+ port->polarity = polarity;
+
+ return 0;
+}
+
+static int tcpm_set_vconn(struct tcpm_port *port, bool enable)
+{
+ int ret;
+
+ dev_dbg(port->dev, "TCPM: set vconn = %d\n", enable);
+
+ ret = port->tcpc->set_vconn(port->tcpc, enable);
+ if (!ret)
+ port->vconn_role = enable ? TYPEC_SOURCE : TYPEC_SINK;
+
+ return ret;
+}
+
+static u32 tcpm_get_current_limit(struct tcpm_port *port)
+{
+ enum typec_cc_status cc;
+ u32 limit;
+
+ cc = port->polarity ? port->cc2 : port->cc1;
+ switch (cc) {
+ case TYPEC_CC_RP_1_5:
+ limit = 1500;
+ break;
+ case TYPEC_CC_RP_3_0:
+ limit = 3000;
+ break;
+ case TYPEC_CC_RP_DEF:
+ default:
+ limit = 0;
+ break;
+ }
+
+ return limit;
+}
+
+static int tcpm_set_current_limit(struct tcpm_port *port, u32 max_ma, u32 mv)
+{
+ int ret = -EOPNOTSUPP;
+
+ dev_info(port->dev, "TCPM: set voltage limit = %u mV\n", mv);
+ dev_info(port->dev, "TCPM: set current limit = %u mA\n", max_ma);
+
+ port->supply_voltage = mv;
+ port->current_limit = max_ma;
+
+ return ret;
+}
+
+static int tcpm_set_attached_state(struct tcpm_port *port, bool attached)
+{
+ return port->tcpc->set_roles(port->tcpc, attached, port->pwr_role,
+ port->data_role);
+}
+
+static int tcpm_set_roles(struct tcpm_port *port, bool attached,
+ enum typec_role role, enum typec_data_role data)
+{
+ int ret;
+
+ ret = port->tcpc->set_roles(port->tcpc, attached, role, data);
+ if (ret < 0)
+ return ret;
+
+ port->pwr_role = role;
+ port->data_role = data;
+
+ return 0;
+}
+
+static int tcpm_pd_send_source_caps(struct tcpm_port *port)
+{
+ struct pd_message msg;
+ int i;
+
+ memset(&msg, 0, sizeof(msg));
+
+ if (!port->nr_src_pdo) {
+ /* No source capabilities defined, sink only */
+ msg.header = PD_HEADER_LE(PD_CTRL_REJECT,
+ port->pwr_role,
+ port->data_role,
+ port->negotiated_rev,
+ port->message_id, 0);
+ } else {
+ msg.header = PD_HEADER_LE(PD_DATA_SOURCE_CAP,
+ port->pwr_role,
+ port->data_role,
+ port->negotiated_rev,
+ port->message_id,
+ port->nr_src_pdo);
+ }
+
+ for (i = 0; i < port->nr_src_pdo; i++)
+ msg.payload[i] = cpu_to_le32(port->src_pdo[i]);
+
+ return tcpm_pd_transmit(port, TCPC_TX_SOP, &msg);
+}
+
+static int tcpm_pd_send_sink_caps(struct tcpm_port *port)
+{
+ struct pd_message msg;
+ unsigned int i;
+
+ memset(&msg, 0, sizeof(msg));
+
+ if (!port->nr_snk_pdo) {
+ /* No sink capabilities defined, source only */
+ msg.header = PD_HEADER_LE(PD_CTRL_REJECT,
+ port->pwr_role,
+ port->data_role,
+ port->negotiated_rev,
+ port->message_id, 0);
+ } else {
+ msg.header = PD_HEADER_LE(PD_DATA_SINK_CAP,
+ port->pwr_role,
+ port->data_role,
+ port->negotiated_rev,
+ port->message_id,
+ port->nr_snk_pdo);
+ }
+
+ for (i = 0; i < port->nr_snk_pdo; i++)
+ msg.payload[i] = cpu_to_le32(port->snk_pdo[i]);
+
+ return tcpm_pd_transmit(port, TCPC_TX_SOP, &msg);
+}
+
+static void tcpm_state_machine(struct tcpm_port *port);
+
+static void tcpm_timer_uninit(struct tcpm_port *port)
+{
+ port->delay_target = 0;
+}
+
+static void tcpm_timer_init(struct tcpm_port *port, uint32_t ms)
+{
+ unsigned long time_us = ms * 1000;
+
+ port->delay_target = timer_get_us() + time_us;
+}
+
+static void tcpm_check_and_run_delayed_work(struct tcpm_port *port)
+{
+ /* no delayed state changes scheduled */
+ if (port->delay_target == 0)
+ return;
+
+ /* it's not yet time */
+ if (timer_get_us() < port->delay_target)
+ return;
+
+ tcpm_timer_uninit(port);
+ tcpm_state_machine(port);
+}
+
+static void mod_tcpm_delayed_work(struct tcpm_port *port, unsigned int
delay_ms)
+{
+ if (delay_ms) {
+ tcpm_timer_init(port, delay_ms);
+ } else {
+ tcpm_timer_uninit(port);
+ tcpm_state_machine(port);
+ }
+}
+
+static void tcpm_set_state(struct tcpm_port *port, enum tcpm_state state,
+ unsigned int delay_ms)
+{
+ if (delay_ms) {
+ dev_dbg(port->dev, "TCPM: pending state change %s -> %s @ %u ms
[%s]\n",
+ tcpm_states[port->state], tcpm_states[state], delay_ms,
+ pd_rev[port->negotiated_rev]);
+ port->delayed_state = state;
+ mod_tcpm_delayed_work(port, delay_ms);
+ port->delay_ms = delay_ms;
+ } else {
+ dev_dbg(port->dev, "TCPM: state change %s -> %s\n",
+ tcpm_states[port->state], tcpm_states[state]);
+ port->delayed_state = INVALID_STATE;
+ port->prev_state = port->state;
+ port->state = state;
+ /*
+ * Don't re-queue the state machine work item if we're currently
+ * in the state machine and we're immediately changing states.
+ * tcpm_state_machine_work() will continue running the state
+ * machine.
+ */
+ if (!port->state_machine_running)
+ mod_tcpm_delayed_work(port, 0);
+ }
+}
+
+static void tcpm_set_state_cond(struct tcpm_port *port, enum tcpm_state state,
+ unsigned int delay_ms)
+{
+ if (port->enter_state == port->state)
+ tcpm_set_state(port, state, delay_ms);
+ else
+ dev_dbg(port->dev, "TCPM: skipped %sstate change %s -> %s [%u
ms], context state %s [%s]\n",
+ delay_ms ? "delayed " : "",
+ tcpm_states[port->state], tcpm_states[state],
+ delay_ms, tcpm_states[port->enter_state],
+ pd_rev[port->negotiated_rev]);
+}
+
+static void tcpm_queue_message(struct tcpm_port *port,
+ enum pd_msg_request message)
+{
+ port->queued_message = message;
+ mod_tcpm_delayed_work(port, 0);
+}
+
+enum pdo_err {
+ PDO_NO_ERR,
+ PDO_ERR_NO_VSAFE5V,
+ PDO_ERR_VSAFE5V_NOT_FIRST,
+ PDO_ERR_PDO_TYPE_NOT_IN_ORDER,
+ PDO_ERR_FIXED_NOT_SORTED,
+ PDO_ERR_VARIABLE_BATT_NOT_SORTED,
+ PDO_ERR_DUPE_PDO,
+ PDO_ERR_PPS_APDO_NOT_SORTED,
+ PDO_ERR_DUPE_PPS_APDO,
+};
+
+static const char * const pdo_err_msg[] = {
+ [PDO_ERR_NO_VSAFE5V] =
+ " err: source/sink caps should at least have vSafe5V",
+ [PDO_ERR_VSAFE5V_NOT_FIRST] =
+ " err: vSafe5V Fixed Supply Object Shall always be the first object",
+ [PDO_ERR_PDO_TYPE_NOT_IN_ORDER] =
+ " err: PDOs should be in the following order: Fixed; Battery; Variable",
+ [PDO_ERR_FIXED_NOT_SORTED] =
+ " err: Fixed supply pdos should be in increasing order of their fixed
voltage",
+ [PDO_ERR_VARIABLE_BATT_NOT_SORTED] =
+ " err: Variable/Battery supply pdos should be in increasing order of
their minimum voltage",
+ [PDO_ERR_DUPE_PDO] =
+ " err: Variable/Batt supply pdos cannot have same min/max voltage",
+ [PDO_ERR_PPS_APDO_NOT_SORTED] =
+ " err: Programmable power supply apdos should be in increasing order of
their maximum voltage",
+ [PDO_ERR_DUPE_PPS_APDO] =
+ " err: Programmable power supply apdos cannot have same min/max voltage
and max current",
+};
+
+static enum pdo_err tcpm_caps_err(struct tcpm_port *port, const u32 *pdo,
+ unsigned int nr_pdo)
+{
+ unsigned int i;
+
+ /* Should at least contain vSafe5v */
+ if (nr_pdo < 1)
+ return PDO_ERR_NO_VSAFE5V;
+
+ /* The vSafe5V Fixed Supply Object Shall always be the first object */
+ if (pdo_type(pdo[0]) != PDO_TYPE_FIXED ||
+ pdo_fixed_voltage(pdo[0]) != VSAFE5V)
+ return PDO_ERR_VSAFE5V_NOT_FIRST;
+
+ for (i = 1; i < nr_pdo; i++) {
+ if (pdo_type(pdo[i]) < pdo_type(pdo[i - 1])) {
+ return PDO_ERR_PDO_TYPE_NOT_IN_ORDER;
+ } else if (pdo_type(pdo[i]) == pdo_type(pdo[i - 1])) {
+ enum pd_pdo_type type = pdo_type(pdo[i]);
+
+ switch (type) {
+ /*
+ * The remaining Fixed Supply Objects, if
+ * present, shall be sent in voltage order;
+ * lowest to highest.
+ */
+ case PDO_TYPE_FIXED:
+ if (pdo_fixed_voltage(pdo[i]) <=
+ pdo_fixed_voltage(pdo[i - 1]))
+ return PDO_ERR_FIXED_NOT_SORTED;
+ break;
+ /*
+ * The Battery Supply Objects and Variable
+ * supply, if present shall be sent in Minimum
+ * Voltage order; lowest to highest.
+ */
+ case PDO_TYPE_VAR:
+ case PDO_TYPE_BATT:
+ if (pdo_min_voltage(pdo[i]) <
+ pdo_min_voltage(pdo[i - 1]))
+ return PDO_ERR_VARIABLE_BATT_NOT_SORTED;
+ else if ((pdo_min_voltage(pdo[i]) ==
+ pdo_min_voltage(pdo[i - 1])) &&
+ (pdo_max_voltage(pdo[i]) ==
+ pdo_max_voltage(pdo[i - 1])))
+ return PDO_ERR_DUPE_PDO;
+ break;
+ /*
+ * The Programmable Power Supply APDOs, if present,
+ * shall be sent in Maximum Voltage order;
+ * lowest to highest.
+ */
+ case PDO_TYPE_APDO:
+ if (pdo_apdo_type(pdo[i]) != APDO_TYPE_PPS)
+ break;
+
+ if (pdo_pps_apdo_max_voltage(pdo[i]) <
+ pdo_pps_apdo_max_voltage(pdo[i - 1]))
+ return PDO_ERR_PPS_APDO_NOT_SORTED;
+ else if (pdo_pps_apdo_min_voltage(pdo[i]) ==
+ pdo_pps_apdo_min_voltage(pdo[i - 1])
&&
+ pdo_pps_apdo_max_voltage(pdo[i]) ==
+ pdo_pps_apdo_max_voltage(pdo[i - 1])
&&
+ pdo_pps_apdo_max_current(pdo[i]) ==
+ pdo_pps_apdo_max_current(pdo[i - 1]))
+ return PDO_ERR_DUPE_PPS_APDO;
+ break;
+ default:
+ dev_err(port->dev, "TCPM: Unknown pdo type\n");
+ }
+ }
+ }
+
+ return PDO_NO_ERR;
+}
+
+static int tcpm_validate_caps(struct tcpm_port *port, const u32 *pdo,
+ unsigned int nr_pdo)
+{
+ enum pdo_err err_index = tcpm_caps_err(port, pdo, nr_pdo);
+
+ if (err_index != PDO_NO_ERR) {
+ dev_err(port->dev, "TCPM:%s\n", pdo_err_msg[err_index]);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
+ * PD (data, control) command handling functions
+ */
+static inline enum tcpm_state ready_state(struct tcpm_port *port)
+{
+ if (port->pwr_role == TYPEC_SOURCE)
+ return SRC_READY;
+ else
+ return SNK_READY;
+}
+
+static int tcpm_pd_send_control(struct tcpm_port *port,
+ enum pd_ctrl_msg_type type);
+
+static void tcpm_pd_data_request(struct tcpm_port *port,
+ const struct pd_message *msg)
+{
+ enum pd_data_msg_type type = pd_header_type_le(msg->header);
+ unsigned int cnt = pd_header_cnt_le(msg->header);
+ unsigned int rev = pd_header_rev_le(msg->header);
+ unsigned int i;
+
+ switch (type) {
+ case PD_DATA_SOURCE_CAP:
+ for (i = 0; i < cnt; i++)
+ port->source_caps[i] = le32_to_cpu(msg->payload[i]);
+
+ port->nr_source_caps = cnt;
+
+ tcpm_validate_caps(port, port->source_caps,
+ port->nr_source_caps);
+
+ /*
+ * Adjust revision in subsequent message headers, as required,
+ * to comply with 6.2.1.1.5 of the USB PD 3.0 spec. We don't
+ * support Rev 1.0 so just do nothing in that scenario.
+ */
+ if (rev == PD_REV10)
+ break;
+
+ if (rev < PD_MAX_REV)
+ port->negotiated_rev = rev;
+
+ if ((pdo_type(port->source_caps[0]) == PDO_TYPE_FIXED) &&
+ (port->source_caps[0] & PDO_FIXED_DUAL_ROLE) &&
+ (port->source_caps[0] & PDO_FIXED_DATA_SWAP)) {
+ /* Dual role power and data, eg: self-powered Type-C */
+ port->wait_dr_swap_message = true;
+ } else {
+ /* Non-Dual role power, eg: adapter */
+ port->wait_dr_swap_message = false;
+ }
+
+ /*
+ * This message may be received even if VBUS is not
+ * present. This is quite unexpected; see USB PD
+ * specification, sections 8.3.3.6.3.1 and 8.3.3.6.3.2.
+ * However, at the same time, we must be ready to
+ * receive this message and respond to it 15ms after
+ * receiving PS_RDY during power swap operations, no matter
+ * if VBUS is available or not (USB PD specification,
+ * section 6.5.9.2).
+ * So we need to accept the message either way,
+ * but be prepared to keep waiting for VBUS after it was
+ * handled.
+ */
+ tcpm_set_state(port, SNK_NEGOTIATE_CAPABILITIES, 0);
+ break;
+ case PD_DATA_REQUEST:
+ /*
+ * Adjust revision in subsequent message headers, as required,
+ * to comply with 6.2.1.1.5 of the USB PD 3.0 spec. We don't
+ * support Rev 1.0 so just reject in that scenario.
+ */
+ if (rev == PD_REV10) {
+ tcpm_queue_message(port, PD_MSG_CTRL_REJECT);
+ break;
+ }
+
+ if (rev < PD_MAX_REV)
+ port->negotiated_rev = rev;
+
+ port->sink_request = le32_to_cpu(msg->payload[0]);
+
+ tcpm_set_state(port, SRC_NEGOTIATE_CAPABILITIES, 0);
+ break;
+ case PD_DATA_SINK_CAP:
+ /* We don't do anything with this at the moment... */
+ for (i = 0; i < cnt; i++)
+ port->sink_caps[i] = le32_to_cpu(msg->payload[i]);
+
+ port->nr_sink_caps = cnt;
+ break;
+ default:
+ break;
+ }
+}
+
+static void tcpm_pd_ctrl_request(struct tcpm_port *port,
+ const struct pd_message *msg)
+{
+ enum pd_ctrl_msg_type type = pd_header_type_le(msg->header);
+ enum tcpm_state next_state;
+
+ switch (type) {
+ case PD_CTRL_GOOD_CRC:
+ case PD_CTRL_PING:
+ break;
+ case PD_CTRL_GET_SOURCE_CAP:
+ switch (port->state) {
+ case SRC_READY:
+ case SNK_READY:
+ tcpm_queue_message(port, PD_MSG_DATA_SOURCE_CAP);
+ break;
+ default:
+ tcpm_queue_message(port, PD_MSG_CTRL_REJECT);
+ break;
+ }
+ break;
+ case PD_CTRL_GET_SINK_CAP:
+ switch (port->state) {
+ case SRC_READY:
+ case SNK_READY:
+ tcpm_queue_message(port, PD_MSG_DATA_SINK_CAP);
+ break;
+ default:
+ tcpm_queue_message(port, PD_MSG_CTRL_REJECT);
+ break;
+ }
+ break;
+ case PD_CTRL_GOTO_MIN:
+ break;
+ case PD_CTRL_PS_RDY:
+ switch (port->state) {
+ case SNK_TRANSITION_SINK:
+ if (port->vbus_present) {
+ tcpm_set_current_limit(port,
+ port->req_current_limit,
+
port->req_supply_voltage);
+ port->explicit_contract = true;
+ tcpm_set_state(port, SNK_READY, 0);
+ } else {
+ /*
+ * Seen after power swap. Keep waiting for VBUS
+ * in a transitional state.
+ */
+ tcpm_set_state(port,
+ SNK_TRANSITION_SINK_VBUS, 0);
+ }
+ break;
+ default:
+ break;
+ }
+ break;
+ case PD_CTRL_REJECT:
+ case PD_CTRL_WAIT:
+ case PD_CTRL_NOT_SUPP:
+ switch (port->state) {
+ case SNK_NEGOTIATE_CAPABILITIES:
+ /* USB PD specification, Figure 8-43 */
+ if (port->explicit_contract)
+ next_state = SNK_READY;
+ else
+ next_state = SNK_WAIT_CAPABILITIES;
+
+ tcpm_set_state(port, next_state, 0);
+ break;
+ default:
+ break;
+ }
+ break;
+ case PD_CTRL_ACCEPT:
+ switch (port->state) {
+ case SNK_NEGOTIATE_CAPABILITIES:
+ tcpm_set_state(port, SNK_TRANSITION_SINK, 0);
+ break;
+ case SOFT_RESET_SEND:
+ port->message_id = 0;
+ port->rx_msgid = -1;
+ if (port->pwr_role == TYPEC_SOURCE)
+ next_state = SRC_SEND_CAPABILITIES;
+ else
+ next_state = SNK_WAIT_CAPABILITIES;
+ tcpm_set_state(port, next_state, 0);
+ break;
+ default:
+ break;
+ }
+ break;
+ case PD_CTRL_SOFT_RESET:
+ tcpm_set_state(port, SOFT_RESET, 0);
+ break;
+ case PD_CTRL_DR_SWAP:
+ if (port->port_type != TYPEC_PORT_DRP) {
+ tcpm_queue_message(port, PD_MSG_CTRL_REJECT);
+ break;
+ }
+ /*
+ * XXX
+ * 6.3.9: If an alternate mode is active, a request to swap
+ * alternate modes shall trigger a port reset.
+ */
+ switch (port->state) {
+ case SRC_READY:
+ case SNK_READY:
+ tcpm_set_state(port, DR_SWAP_ACCEPT, 0);
+ break;
+ default:
+ tcpm_queue_message(port, PD_MSG_CTRL_WAIT);
+ break;
+ }
+ break;
+ case PD_CTRL_PR_SWAP:
+ case PD_CTRL_VCONN_SWAP:
+ case PD_CTRL_GET_SOURCE_CAP_EXT:
+ case PD_CTRL_GET_STATUS:
+ case PD_CTRL_FR_SWAP:
+ case PD_CTRL_GET_PPS_STATUS:
+ case PD_CTRL_GET_COUNTRY_CODES:
+ /* Currently not supported */
+ dev_err(port->dev, "TCPM: Currently not supported type %#x\n",
type);
+ tcpm_queue_message(port, PD_MSG_CTRL_NOT_SUPP);
+ break;
+ default:
+ dev_err(port->dev, "TCPM: Unrecognized ctrl message type
%#x\n", type);
+ break;
+ }
+}
+
+static void tcpm_pd_rx_handler(struct tcpm_port *port,
+ struct pd_rx_event *event)
+{
+ const struct pd_message *msg = &event->msg;
+ unsigned int cnt = pd_header_cnt_le(msg->header);
+ bool remote_is_host, local_is_host;
+
+ dev_dbg(port->dev, "TCPM: PD RX, header: %#x [%d]\n",
+ le16_to_cpu(msg->header), port->attached);
+
+ if (port->attached) {
+ enum pd_ctrl_msg_type type = pd_header_type_le(msg->header);
+ unsigned int msgid = pd_header_msgid_le(msg->header);
+
+ /*
+ * USB PD standard, 6.6.1.2:
+ * "... if MessageID value in a received Message is the
+ * same as the stored value, the receiver shall return a
+ * GoodCRC Message with that MessageID value and drop
+ * the Message (this is a retry of an already received
+ * Message). Note: this shall not apply to the Soft_Reset
+ * Message which always has a MessageID value of zero."
+ */
+ if (msgid == port->rx_msgid && type != PD_CTRL_SOFT_RESET)
+ goto done;
+ port->rx_msgid = msgid;
+
+ /*
+ * If both ends believe to be DFP/host, we have a data role
+ * mismatch.
+ */
+ remote_is_host = !!(le16_to_cpu(msg->header) &
PD_HEADER_DATA_ROLE);
+ local_is_host = port->data_role == TYPEC_HOST;
+ if (remote_is_host == local_is_host) {
+ dev_err(port->dev, "TCPM: data role mismatch,
initiating error recovery\n");
+ tcpm_set_state(port, ERROR_RECOVERY, 0);
+ } else {
+ if (cnt)
+ tcpm_pd_data_request(port, msg);
+ else
+ tcpm_pd_ctrl_request(port, msg);
+ }
+ }
+
+done:
+ kfree(event);
+}
+
+void tcpm_pd_receive(struct tcpm_port *port, const struct pd_message *msg)
+{
+ struct pd_rx_event *event;
+
+ port->poll_event_cnt = 0;
+ event = kzalloc(sizeof(*event), GFP_ATOMIC);
+ if (!event)
+ return;
+
+ event->port = port;
+ memcpy(&event->msg, msg, sizeof(*msg));
+ tcpm_pd_rx_handler(port, event);
+}
+EXPORT_SYMBOL_GPL(tcpm_pd_receive);
+
+static int tcpm_pd_send_control(struct tcpm_port *port,
+ enum pd_ctrl_msg_type type)
+{
+ struct pd_message msg;
+
+ memset(&msg, 0, sizeof(msg));
+ msg.header = PD_HEADER_LE(type, port->pwr_role,
+ port->data_role,
+ port->negotiated_rev,
+ port->message_id, 0);
+
+ return tcpm_pd_transmit(port, TCPC_TX_SOP, &msg);
+}
+
+/*
+ * Send queued message without affecting state.
+ * Return true if state machine should go back to sleep,
+ * false otherwise.
+ */
+static bool tcpm_send_queued_message(struct tcpm_port *port)
+{
+ enum pd_msg_request queued_message;
+
+ do {
+ queued_message = port->queued_message;
+ port->queued_message = PD_MSG_NONE;
+
+ switch (queued_message) {
+ case PD_MSG_CTRL_WAIT:
+ tcpm_pd_send_control(port, PD_CTRL_WAIT);
+ break;
+ case PD_MSG_CTRL_REJECT:
+ tcpm_pd_send_control(port, PD_CTRL_REJECT);
+ break;
+ case PD_MSG_CTRL_NOT_SUPP:
+ tcpm_pd_send_control(port, PD_CTRL_NOT_SUPP);
+ break;
+ case PD_MSG_DATA_SINK_CAP:
+ tcpm_pd_send_sink_caps(port);
+ break;
+ case PD_MSG_DATA_SOURCE_CAP:
+ tcpm_pd_send_source_caps(port);
+ break;
+ default:
+ break;
+ }
+ } while (port->queued_message != PD_MSG_NONE);
+
+ return false;
+}
+
+static int tcpm_pd_check_request(struct tcpm_port *port)
+{
+ u32 pdo, rdo = port->sink_request;
+ unsigned int max, op, pdo_max, index;
+ enum pd_pdo_type type;
+
+ index = rdo_index(rdo);
+ if (!index || index > port->nr_src_pdo)
+ return -EINVAL;
+
+ pdo = port->src_pdo[index - 1];
+ type = pdo_type(pdo);
+ switch (type) {
+ case PDO_TYPE_FIXED:
+ case PDO_TYPE_VAR:
+ max = rdo_max_current(rdo);
+ op = rdo_op_current(rdo);
+ pdo_max = pdo_max_current(pdo);
+
+ if (op > pdo_max)
+ return -EINVAL;
+ if (max > pdo_max && !(rdo & RDO_CAP_MISMATCH))
+ return -EINVAL;
+
+ if (type == PDO_TYPE_FIXED)
+ dev_dbg(port->dev, "TCPM: Requested %u mV, %u mA for %u
/ %u mA\n",
+ pdo_fixed_voltage(pdo), pdo_max, op, max);
+ else
+ dev_dbg(port->dev, "TCPM: Requested %u -> %u mV, %u mA
for %u / %u mA\n",
+ pdo_min_voltage(pdo), pdo_max_voltage(pdo),
+ pdo_max, op, max);
+ break;
+ case PDO_TYPE_BATT:
+ max = rdo_max_power(rdo);
+ op = rdo_op_power(rdo);
+ pdo_max = pdo_max_power(pdo);
+
+ if (op > pdo_max)
+ return -EINVAL;
+ if (max > pdo_max && !(rdo & RDO_CAP_MISMATCH))
+ return -EINVAL;
+ dev_info(port->dev, "TCPM: Requested %u -> %u mV, %u mW for %u
/ %u mW\n",
+ pdo_min_voltage(pdo), pdo_max_voltage(pdo),
+ pdo_max, op, max);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+#define min_power(x, y) min(pdo_max_power(x), pdo_max_power(y))
+#define min_current(x, y) min(pdo_max_current(x), pdo_max_current(y))
+
+static int tcpm_pd_select_pdo(struct tcpm_port *port, int *sink_pdo,
+ int *src_pdo)
+{
+ unsigned int i, j, max_src_mv = 0, min_src_mv = 0, max_mw = 0,
+ max_mv = 0, src_mw = 0, src_ma = 0, max_snk_mv = 0,
+ min_snk_mv = 0;
+ int ret = -EINVAL;
+
+ /*
+ * Select the source PDO providing the most power which has a
+ * matchig sink cap.
+ */
+ for (i = 0; i < port->nr_source_caps; i++) {
+ u32 pdo = port->source_caps[i];
+ enum pd_pdo_type type = pdo_type(pdo);
+
+ switch (type) {
+ case PDO_TYPE_FIXED:
+ max_src_mv = pdo_fixed_voltage(pdo);
+ min_src_mv = max_src_mv;
+ break;
+ case PDO_TYPE_BATT:
+ case PDO_TYPE_VAR:
+ max_src_mv = pdo_max_voltage(pdo);
+ min_src_mv = pdo_min_voltage(pdo);
+ break;
+ case PDO_TYPE_APDO:
+ continue;
+ default:
+ dev_err(port->dev, "TCPM: Invalid source PDO type,
ignoring\n");
+ continue;
+ }
+
+ switch (type) {
+ case PDO_TYPE_FIXED:
+ case PDO_TYPE_VAR:
+ src_ma = pdo_max_current(pdo);
+ src_mw = src_ma * min_src_mv / 1000;
+ break;
+ case PDO_TYPE_BATT:
+ src_mw = pdo_max_power(pdo);
+ break;
+ case PDO_TYPE_APDO:
+ continue;
+ default:
+ dev_err(port->dev, "TCPM: Invalid source PDO type,
ignoring\n");
+ continue;
+ }
+
+ for (j = 0; j < port->nr_snk_pdo; j++) {
+ pdo = port->snk_pdo[j];
+
+ switch (pdo_type(pdo)) {
+ case PDO_TYPE_FIXED:
+ max_snk_mv = pdo_fixed_voltage(pdo);
+ min_snk_mv = max_snk_mv;
+ break;
+ case PDO_TYPE_BATT:
+ case PDO_TYPE_VAR:
+ max_snk_mv = pdo_max_voltage(pdo);
+ min_snk_mv = pdo_min_voltage(pdo);
+ break;
+ case PDO_TYPE_APDO:
+ continue;
+ default:
+ dev_err(port->dev, "TCPM: Invalid sink PDO
type, ignoring\n");
+ continue;
+ }
+
+ if (max_src_mv <= max_snk_mv && min_src_mv >=
min_snk_mv) {
+ /* Prefer higher voltages if available */
+ if ((src_mw == max_mw && min_src_mv > max_mv) ||
+ src_mw > max_mw) {
+ *src_pdo = i;
+ *sink_pdo = j;
+ max_mw = src_mw;
+ max_mv = min_src_mv;
+ ret = 0;
+ }
+ }
+ }
+ }
+
+ return ret;
+}
+
+static int tcpm_pd_build_request(struct tcpm_port *port, u32 *rdo)
+{
+ unsigned int mv, ma, mw, flags;
+ unsigned int max_ma, max_mw;
+ enum pd_pdo_type type;
+ u32 pdo, matching_snk_pdo;
+ int src_pdo_index = 0;
+ int snk_pdo_index = 0;
+ int ret;
+
+ ret = tcpm_pd_select_pdo(port, &snk_pdo_index, &src_pdo_index);
+ if (ret < 0)
+ return ret;
+
+ pdo = port->source_caps[src_pdo_index];
+ matching_snk_pdo = port->snk_pdo[snk_pdo_index];
+ type = pdo_type(pdo);
+
+ switch (type) {
+ case PDO_TYPE_FIXED:
+ mv = pdo_fixed_voltage(pdo);
+ break;
+ case PDO_TYPE_BATT:
+ case PDO_TYPE_VAR:
+ mv = pdo_min_voltage(pdo);
+ break;
+ default:
+ dev_err(port->dev, "TCPM: Invalid PDO selected!\n");
+ return -EINVAL;
+ }
+
+ /* Select maximum available current within the sink pdo's limit */
+ if (type == PDO_TYPE_BATT) {
+ mw = min_power(pdo, matching_snk_pdo);
+ ma = 1000 * mw / mv;
+ } else {
+ ma = min_current(pdo, matching_snk_pdo);
+ mw = ma * mv / 1000;
+ }
+
+ flags = RDO_USB_COMM | RDO_NO_SUSPEND;
+
+ /* Set mismatch bit if offered power is less than operating power */
+ max_ma = ma;
+ max_mw = mw;
+ if (mw < port->operating_snk_mw) {
+ flags |= RDO_CAP_MISMATCH;
+ if (type == PDO_TYPE_BATT &&
+ (pdo_max_power(matching_snk_pdo) > pdo_max_power(pdo)))
+ max_mw = pdo_max_power(matching_snk_pdo);
+ else if (pdo_max_current(matching_snk_pdo) >
+ pdo_max_current(pdo))
+ max_ma = pdo_max_current(matching_snk_pdo);
+ }
+
+ dev_dbg(port->dev, "TCPM: cc=%d cc1=%d cc2=%d vbus=%d vconn=%s
polarity=%d\n",
+ port->cc_req, port->cc1, port->cc2, port->vbus_source,
+ port->vconn_role == TYPEC_SOURCE ? "source" : "sink",
+ port->polarity);
+
+ if (type == PDO_TYPE_BATT) {
+ *rdo = RDO_BATT(src_pdo_index + 1, mw, max_mw, flags);
+
+ dev_info(port->dev, "TCPM: requesting PDO %d: %u mV, %u mW%s\n",
+ src_pdo_index, mv, mw,
+ flags & RDO_CAP_MISMATCH ? " [mismatch]" : "");
+ } else {
+ *rdo = RDO_FIXED(src_pdo_index + 1, ma, max_ma, flags);
+
+ dev_info(port->dev, "TCPM: requesting PDO %d: %u mV, %u mA%s\n",
+ src_pdo_index, mv, ma,
+ flags & RDO_CAP_MISMATCH ? " [mismatch]" : "");
+ }
+
+ port->req_current_limit = ma;
+ port->req_supply_voltage = mv;
+
+ return 0;
+}
+
+static int tcpm_pd_send_request(struct tcpm_port *port)
+{
+ struct pd_message msg;
+ int ret;
+ u32 rdo;
+
+ ret = tcpm_pd_build_request(port, &rdo);
+ if (ret < 0)
+ return ret;
+
+ memset(&msg, 0, sizeof(msg));
+ msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
+ port->pwr_role,
+ port->data_role,
+ port->negotiated_rev,
+ port->message_id, 1);
+ msg.payload[0] = cpu_to_le32(rdo);
+
+ return tcpm_pd_transmit(port, TCPC_TX_SOP, &msg);
+}
+
+static int tcpm_set_vbus(struct tcpm_port *port, bool enable)
+{
+ int ret;
+
+ if (enable && port->vbus_charge)
+ return -EINVAL;
+
+ dev_dbg(port->dev, "TCPM: set vbus = %d charge = %d\n",
+ enable, port->vbus_charge);
+
+ ret = port->tcpc->set_vbus(port->tcpc, enable, port->vbus_charge);
+ if (ret < 0)
+ return ret;
+
+ port->vbus_source = enable;
+ return 0;
+}
+
+static int tcpm_set_charge(struct tcpm_port *port, bool charge)
+{
+ int ret;
+
+ if (charge && port->vbus_source)
+ return -EINVAL;
+
+ if (charge != port->vbus_charge) {
+ dev_dbg(port->dev, "TCPM: set vbus = %d charge = %d\n",
+ port->vbus_source, charge);
+ ret = port->tcpc->set_vbus(port->tcpc, port->vbus_source,
+ charge);
+ if (ret < 0)
+ return ret;
+ }
+ port->vbus_charge = charge;
+ return 0;
+}
+
+static bool tcpm_start_toggling(struct tcpm_port *port, enum typec_cc_status
cc)
+{
+ int ret;
+
+ if (!port->tcpc->start_toggling)
+ return false;
+
+ dev_dbg(port->dev, "TCPM: Start toggling\n");
+ ret = port->tcpc->start_toggling(port->tcpc, port->port_type, cc);
+ return ret == 0;
+}
+
+static int tcpm_init_vbus(struct tcpm_port *port)
+{
+ int ret;
+
+ ret = port->tcpc->set_vbus(port->tcpc, false, false);
+ port->vbus_source = false;
+ port->vbus_charge = false;
+ return ret;
+}
+
+static int tcpm_init_vconn(struct tcpm_port *port)
+{
+ int ret;
+
+ ret = port->tcpc->set_vconn(port->tcpc, false);
+ port->vconn_role = TYPEC_SINK;
+ return ret;
+}
+
+static void tcpm_typec_connect(struct tcpm_port *port)
+{
+ if (!port->connected)
+ port->connected = true;
+}
+
+static int tcpm_src_attach(struct tcpm_port *port)
+{
+ enum typec_cc_polarity polarity =
+ port->cc2 == TYPEC_CC_RD ? TYPEC_POLARITY_CC2
+ : TYPEC_POLARITY_CC1;
+ int ret;
+
+ if (port->attached)
+ return 0;
+
+ ret = tcpm_set_polarity(port, polarity);
+ if (ret < 0)
+ return ret;
+
+ ret = tcpm_set_roles(port, true, TYPEC_SOURCE, TYPEC_HOST);
+ if (ret < 0)
+ return ret;
+
+ ret = port->tcpc->set_pd_rx(port->tcpc, true);
+ if (ret < 0)
+ goto out_disable_mux;
+
+ /*
+ * USB Type-C specification, version 1.2,
+ * chapter 4.5.2.2.8.1 (Attached.SRC Requirements)
+ * Enable VCONN only if the non-RD port is set to RA.
+ */
+ if ((polarity == TYPEC_POLARITY_CC1 && port->cc2 == TYPEC_CC_RA) ||
+ (polarity == TYPEC_POLARITY_CC2 && port->cc1 == TYPEC_CC_RA)) {
+ ret = tcpm_set_vconn(port, true);
+ if (ret < 0)
+ goto out_disable_pd;
+ }
+
+ ret = tcpm_set_vbus(port, true);
+ if (ret < 0)
+ goto out_disable_vconn;
+
+ port->pd_capable = false;
+
+ port->partner = NULL;
+
+ port->attached = true;
+
+ return 0;
+
+out_disable_vconn:
+ tcpm_set_vconn(port, false);
+out_disable_pd:
+ port->tcpc->set_pd_rx(port->tcpc, false);
+out_disable_mux:
+ dev_err(port->dev, "TCPM: CC connected in %s as DFP\n",
+ polarity ? "CC2" : "CC1");
+ return 0;
+}
+
+static void tcpm_typec_disconnect(struct tcpm_port *port)
+{
+ if (port->connected) {
+ port->partner = NULL;
+ port->connected = false;
+ }
+}
+
+static void tcpm_reset_port(struct tcpm_port *port)
+{
+ tcpm_timer_uninit(port);
+ tcpm_typec_disconnect(port);
+ port->poll_event_cnt = 0;
+ port->wait_dr_swap_message = false;
+ port->attached = false;
+ port->pd_capable = false;
+
+ /*
+ * First Rx ID should be 0; set this to a sentinel of -1 so that
+ * we can check tcpm_pd_rx_handler() if we had seen it before.
+ */
+ port->rx_msgid = -1;
+
+ port->tcpc->set_pd_rx(port->tcpc, false);
+ tcpm_init_vbus(port); /* also disables charging */
+ tcpm_init_vconn(port);
+ tcpm_set_current_limit(port, 0, 0);
+ tcpm_set_polarity(port, TYPEC_POLARITY_CC1);
+ tcpm_set_attached_state(port, false);
+ port->nr_sink_caps = 0;
+}
+
+static void tcpm_detach(struct tcpm_port *port)
+{
+ if (tcpm_port_is_disconnected(port))
+ port->hard_reset_count = 0;
+
+ if (!port->attached)
+ return;
+
+ tcpm_reset_port(port);
+}
+
+static void tcpm_src_detach(struct tcpm_port *port)
+{
+ tcpm_detach(port);
+}
+
+static int tcpm_snk_attach(struct tcpm_port *port)
+{
+ int ret;
+
+ if (port->attached)
+ return 0;
+
+ ret = tcpm_set_polarity(port, port->cc2 != TYPEC_CC_OPEN ?
+ TYPEC_POLARITY_CC2 : TYPEC_POLARITY_CC1);
+ if (ret < 0)
+ return ret;
+
+ ret = tcpm_set_roles(port, true, TYPEC_SINK, TYPEC_DEVICE);
+ if (ret < 0)
+ return ret;
+
+ port->pd_capable = false;
+
+ port->partner = NULL;
+
+ port->attached = true;
+ dev_info(port->dev, "TCPM: CC connected in %s as UFP\n",
+ port->cc1 != TYPEC_CC_OPEN ? "CC1" : "CC2");
+
+ return 0;
+}
+
+static void tcpm_snk_detach(struct tcpm_port *port)
+{
+ tcpm_detach(port);
+}
+
+static inline enum tcpm_state hard_reset_state(struct tcpm_port *port)
+{
+ if (port->hard_reset_count < PD_N_HARD_RESET_COUNT)
+ return HARD_RESET_SEND;
+ if (port->pd_capable)
+ return ERROR_RECOVERY;
+ if (port->pwr_role == TYPEC_SOURCE)
+ return SRC_UNATTACHED;
+ if (port->state == SNK_WAIT_CAPABILITIES)
+ return SNK_READY;
+ return SNK_UNATTACHED;
+}
+
+static inline enum tcpm_state unattached_state(struct tcpm_port *port)
+{
+ if (port->port_type == TYPEC_PORT_DRP) {
+ if (port->pwr_role == TYPEC_SOURCE)
+ return SRC_UNATTACHED;
+ else
+ return SNK_UNATTACHED;
+ } else if (port->port_type == TYPEC_PORT_SRC) {
+ return SRC_UNATTACHED;
+ }
+
+ return SNK_UNATTACHED;
+}
+
+static void run_state_machine(struct tcpm_port *port)
+{
+ int ret;
+
+ port->enter_state = port->state;
+ switch (port->state) {
+ case TOGGLING:
+ break;
+ /* SRC states */
+ case SRC_UNATTACHED:
+ tcpm_src_detach(port);
+ if (tcpm_start_toggling(port, tcpm_rp_cc(port))) {
+ tcpm_set_state(port, TOGGLING, 0);
+ break;
+ }
+ tcpm_set_cc(port, tcpm_rp_cc(port));
+ if (port->port_type == TYPEC_PORT_DRP)
+ tcpm_set_state(port, SNK_UNATTACHED, PD_T_DRP_SNK);
+ break;
+ case SRC_ATTACH_WAIT:
+ if (tcpm_port_is_source(port))
+ tcpm_set_state(port, SRC_ATTACHED, PD_T_CC_DEBOUNCE);
+ break;
+
+ case SRC_ATTACHED:
+ ret = tcpm_src_attach(port);
+ /*
+ * Currently, vbus control is not implemented,
+ * and the SRC detection process cannot be fully implemented.
+ */
+ tcpm_set_state(port, SRC_READY, 0);
+ break;
+ case SRC_STARTUP:
+ port->caps_count = 0;
+ port->negotiated_rev = PD_MAX_REV;
+ port->message_id = 0;
+ port->rx_msgid = -1;
+ port->explicit_contract = false;
+ tcpm_set_state(port, SRC_SEND_CAPABILITIES, 0);
+ break;
+ case SRC_SEND_CAPABILITIES:
+ port->caps_count++;
+ if (port->caps_count > PD_N_CAPS_COUNT) {
+ tcpm_set_state(port, SRC_READY, 0);
+ break;
+ }
+ ret = tcpm_pd_send_source_caps(port);
+ if (ret < 0) {
+ tcpm_set_state(port, SRC_SEND_CAPABILITIES,
+ PD_T_SEND_SOURCE_CAP);
+ } else {
+ /*
+ * Per standard, we should clear the reset counter here.
+ * However, that can result in state machine hang-ups.
+ * Reset it only in READY state to improve stability.
+ */
+ /* port->hard_reset_count = 0; */
+ port->caps_count = 0;
+ port->pd_capable = true;
+ tcpm_set_state_cond(port, SRC_SEND_CAPABILITIES_TIMEOUT,
+ PD_T_SEND_SOURCE_CAP);
+ }
+ break;
+ case SRC_SEND_CAPABILITIES_TIMEOUT:
+ /*
+ * Error recovery for a PD_DATA_SOURCE_CAP reply timeout.
+ *
+ * PD 2.0 sinks are supposed to accept src-capabilities with a
+ * 3.0 header and simply ignore any src PDOs which the sink does
+ * not understand such as PPS but some 2.0 sinks instead ignore
+ * the entire PD_DATA_SOURCE_CAP message, causing contract
+ * negotiation to fail.
+ *
+ * After PD_N_HARD_RESET_COUNT hard-reset attempts, we try
+ * sending src-capabilities with a lower PD revision to
+ * make these broken sinks work.
+ */
+ if (port->hard_reset_count < PD_N_HARD_RESET_COUNT) {
+ tcpm_set_state(port, HARD_RESET_SEND, 0);
+ } else if (port->negotiated_rev > PD_REV20) {
+ port->negotiated_rev--;
+ port->hard_reset_count = 0;
+ tcpm_set_state(port, SRC_SEND_CAPABILITIES, 0);
+ } else {
+ tcpm_set_state(port, hard_reset_state(port), 0);
+ }
+ break;
+ case SRC_NEGOTIATE_CAPABILITIES:
+ ret = tcpm_pd_check_request(port);
+ if (ret < 0) {
+ tcpm_pd_send_control(port, PD_CTRL_REJECT);
+ if (!port->explicit_contract) {
+ tcpm_set_state(port,
+ SRC_WAIT_NEW_CAPABILITIES, 0);
+ } else {
+ tcpm_set_state(port, SRC_READY, 0);
+ }
+ } else {
+ tcpm_pd_send_control(port, PD_CTRL_ACCEPT);
+ tcpm_set_state(port, SRC_TRANSITION_SUPPLY,
+ PD_T_SRC_TRANSITION);
+ }
+ break;
+ case SRC_TRANSITION_SUPPLY:
+ /* XXX: regulator_set_voltage(vbus, ...) */
+ tcpm_pd_send_control(port, PD_CTRL_PS_RDY);
+ port->explicit_contract = true;
+ tcpm_set_state_cond(port, SRC_READY, 0);
+ break;
+ case SRC_READY:
+ port->hard_reset_count = 0;
+
+ tcpm_typec_connect(port);
+ break;
+ case SRC_WAIT_NEW_CAPABILITIES:
+ /* Nothing to do... */
+ break;
+
+ /* SNK states */
+ case SNK_UNATTACHED:
+ tcpm_snk_detach(port);
+ if (tcpm_start_toggling(port, TYPEC_CC_RD)) {
+ tcpm_set_state(port, TOGGLING, 0);
+ break;
+ }
+ tcpm_set_cc(port, TYPEC_CC_RD);
+ if (port->port_type == TYPEC_PORT_DRP)
+ tcpm_set_state(port, SRC_UNATTACHED, PD_T_DRP_SRC);
+ break;
+ case SNK_ATTACH_WAIT:
+ if ((port->cc1 == TYPEC_CC_OPEN &&
+ port->cc2 != TYPEC_CC_OPEN) ||
+ (port->cc1 != TYPEC_CC_OPEN &&
+ port->cc2 == TYPEC_CC_OPEN))
+ tcpm_set_state(port, SNK_DEBOUNCED,
+ PD_T_CC_DEBOUNCE);
+ else if (tcpm_port_is_disconnected(port))
+ tcpm_set_state(port, SNK_UNATTACHED,
+ PD_T_CC_DEBOUNCE);
+ break;
+ case SNK_DEBOUNCED:
+ if (tcpm_port_is_disconnected(port))
+ tcpm_set_state(port, SNK_UNATTACHED, PD_T_PD_DEBOUNCE);
+ else if (port->vbus_present)
+ tcpm_set_state(port, SNK_ATTACHED, 0);
+ else
+ /* Wait for VBUS, but not forever */
+ tcpm_set_state(port, PORT_RESET, PD_T_PS_SOURCE_ON);
+ break;
+ case SNK_ATTACHED:
+ ret = tcpm_snk_attach(port);
+ if (ret < 0)
+ tcpm_set_state(port, SNK_UNATTACHED, 0);
+ else
+ tcpm_set_state(port, SNK_STARTUP, 0);
+ break;
+ case SNK_STARTUP:
+ port->negotiated_rev = PD_MAX_REV;
+ port->message_id = 0;
+ port->rx_msgid = -1;
+ port->explicit_contract = false;
+ tcpm_set_state(port, SNK_DISCOVERY, 0);
+ break;
+ case SNK_DISCOVERY:
+ if (port->vbus_present) {
+ tcpm_set_current_limit(port,
+ tcpm_get_current_limit(port),
+ 5000);
+ tcpm_set_charge(port, true);
+ tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
+ break;
+ }
+ /*
+ * For DRP, timeouts differ. Also, handling is supposed to be
+ * different and much more complex (dead battery detection;
+ * see USB power delivery specification, section 8.3.3.6.1.5.1).
+ */
+ tcpm_set_state(port, hard_reset_state(port),
+ port->port_type == TYPEC_PORT_DRP ?
+ PD_T_DB_DETECT : PD_T_NO_RESPONSE);
+ break;
+ case SNK_DISCOVERY_DEBOUNCE:
+ tcpm_set_state(port, SNK_DISCOVERY_DEBOUNCE_DONE,
+ PD_T_CC_DEBOUNCE);
+ break;
+ case SNK_DISCOVERY_DEBOUNCE_DONE:
+ tcpm_set_state(port, unattached_state(port), 0);
+ break;
+ case SNK_WAIT_CAPABILITIES:
+ ret = port->tcpc->set_pd_rx(port->tcpc, true);
+ if (ret < 0) {
+ tcpm_set_state(port, SNK_READY, 0);
+ break;
+ }
+ /*
+ * If VBUS has never been low, and we time out waiting
+ * for source cap, try a soft reset first, in case we
+ * were already in a stable contract before this boot.
+ * Do this only once.
+ */
+ if (port->vbus_never_low) {
+ port->vbus_never_low = false;
+ tcpm_set_state(port, SOFT_RESET_SEND,
+ PD_T_SINK_WAIT_CAP);
+ } else {
+ tcpm_set_state(port, hard_reset_state(port),
+ PD_T_SINK_WAIT_CAP);
+ }
+ break;
+ case SNK_NEGOTIATE_CAPABILITIES:
+ port->pd_capable = true;
+ port->hard_reset_count = 0;
+ ret = tcpm_pd_send_request(port);
+ if (ret < 0) {
+ /* Let the Source send capabilities again. */
+ tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
+ } else {
+ tcpm_set_state_cond(port, hard_reset_state(port),
+ PD_T_SENDER_RESPONSE);
+ }
+ break;
+ case SNK_TRANSITION_SINK:
+ case SNK_TRANSITION_SINK_VBUS:
+ tcpm_set_state(port, hard_reset_state(port),
+ PD_T_PS_TRANSITION);
+ break;
+ case SNK_READY:
+ port->update_sink_caps = false;
+ tcpm_typec_connect(port);
+ /*
+ * Here poll_event_cnt is cleared, waiting for self-powered
Type-C devices
+ * to send DR_swap Messge until 1s (TCPM_POLL_EVENT_TIME_OUT *
500us)timeout
+ */
+ if (port->wait_dr_swap_message)
+ port->poll_event_cnt = 0;
+
+ break;
+
+ /* Hard_Reset states */
+ case HARD_RESET_SEND:
+ tcpm_pd_transmit(port, TCPC_TX_HARD_RESET, NULL);
+ tcpm_set_state(port, HARD_RESET_START, 0);
+ port->wait_dr_swap_message = false;
+ break;
+ case HARD_RESET_START:
+ port->hard_reset_count++;
+ port->tcpc->set_pd_rx(port->tcpc, false);
+ port->nr_sink_caps = 0;
+ if (port->pwr_role == TYPEC_SOURCE)
+ tcpm_set_state(port, SRC_HARD_RESET_VBUS_OFF,
+ PD_T_PS_HARD_RESET);
+ else
+ tcpm_set_state(port, SNK_HARD_RESET_SINK_OFF, 0);
+ break;
+ case SRC_HARD_RESET_VBUS_OFF:
+ tcpm_set_vconn(port, true);
+ tcpm_set_vbus(port, false);
+ tcpm_set_roles(port, port->self_powered, TYPEC_SOURCE,
+ TYPEC_HOST);
+ tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
+ break;
+ case SRC_HARD_RESET_VBUS_ON:
+ tcpm_set_vconn(port, true);
+ tcpm_set_vbus(port, true);
+ port->tcpc->set_pd_rx(port->tcpc, true);
+ tcpm_set_attached_state(port, true);
+ tcpm_set_state(port, SRC_UNATTACHED, PD_T_PS_SOURCE_ON);
+ break;
+ case SNK_HARD_RESET_SINK_OFF:
+ tcpm_set_vconn(port, false);
+ if (port->pd_capable)
+ tcpm_set_charge(port, false);
+ tcpm_set_roles(port, port->self_powered, TYPEC_SINK,
+ TYPEC_DEVICE);
+ /*
+ * VBUS may or may not toggle, depending on the adapter.
+ * If it doesn't toggle, transition to SNK_HARD_RESET_SINK_ON
+ * directly after timeout.
+ */
+ tcpm_set_state(port, SNK_HARD_RESET_SINK_ON, PD_T_SAFE_0V);
+ break;
+ case SNK_HARD_RESET_WAIT_VBUS:
+ /* Assume we're disconnected if VBUS doesn't come back. */
+ tcpm_set_state(port, SNK_UNATTACHED,
+ PD_T_SRC_RECOVER_MAX + PD_T_SRC_TURN_ON);
+ break;
+ case SNK_HARD_RESET_SINK_ON:
+ /* Note: There is no guarantee that VBUS is on in this state */
+ /*
+ * XXX:
+ * The specification suggests that dual mode ports in sink
+ * mode should transition to state PE_SRC_Transition_to_default.
+ * See USB power delivery specification chapter 8.3.3.6.1.3.
+ * This would mean to
+ * - turn off VCONN, reset power supply
+ * - request hardware reset
+ * - turn on VCONN
+ * - Transition to state PE_Src_Startup
+ * SNK only ports shall transition to state Snk_Startup
+ * (see chapter 8.3.3.3.8).
+ * Similar, dual-mode ports in source mode should transition
+ * to PE_SNK_Transition_to_default.
+ */
+ if (port->pd_capable) {
+ tcpm_set_current_limit(port,
+ tcpm_get_current_limit(port),
+ 5000);
+ tcpm_set_charge(port, true);
+ }
+ tcpm_set_attached_state(port, true);
+ tcpm_set_state(port, SNK_STARTUP, 0);
+ break;
+
+ /* Soft_Reset states */
+ case SOFT_RESET:
+ port->message_id = 0;
+ port->rx_msgid = -1;
+ tcpm_pd_send_control(port, PD_CTRL_ACCEPT);
+ if (port->pwr_role == TYPEC_SOURCE)
+ tcpm_set_state(port, SRC_SEND_CAPABILITIES, 0);
+ else
+ tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
+ break;
+ case SOFT_RESET_SEND:
+ port->message_id = 0;
+ port->rx_msgid = -1;
+ if (tcpm_pd_send_control(port, PD_CTRL_SOFT_RESET))
+ tcpm_set_state_cond(port, hard_reset_state(port), 0);
+ else
+ tcpm_set_state_cond(port, hard_reset_state(port),
+ PD_T_SENDER_RESPONSE);
+ break;
+
+ /* DR_Swap states */
+ case DR_SWAP_ACCEPT:
+ tcpm_pd_send_control(port, PD_CTRL_ACCEPT);
+ tcpm_set_state_cond(port, DR_SWAP_CHANGE_DR, 0);
+ break;
+ case DR_SWAP_CHANGE_DR:
+ if (port->data_role == TYPEC_HOST) {
+ tcpm_set_roles(port, true, port->pwr_role,
+ TYPEC_DEVICE);
+ } else {
+ tcpm_set_roles(port, true, port->pwr_role,
+ TYPEC_HOST);
+ }
+ /* DR_swap process complete, wait_dr_swap_message is cleared */
+ port->wait_dr_swap_message = false;
+ tcpm_set_state(port, ready_state(port), 0);
+ break;
+ case ERROR_RECOVERY:
+ tcpm_set_state(port, PORT_RESET, 0);
+ break;
+ case PORT_RESET:
+ tcpm_reset_port(port);
+ if (port->self_powered)
+ tcpm_set_cc(port, TYPEC_CC_OPEN);
+ else
+ tcpm_set_cc(port, tcpm_default_state(port) ==
SNK_UNATTACHED ?
+ TYPEC_CC_RD : tcpm_rp_cc(port));
+ tcpm_set_state(port, PORT_RESET_WAIT_OFF,
+ PD_T_ERROR_RECOVERY);
+ break;
+ case PORT_RESET_WAIT_OFF:
+ tcpm_set_state(port,
+ tcpm_default_state(port),
+ port->vbus_present ? PD_T_PS_SOURCE_OFF : 0);
+ break;
+ default:
+ dev_err(port->dev, "TCPM: Unexpected port state %d\n",
port->state);
+ break;
+ }
+}
+
+static void tcpm_state_machine(struct tcpm_port *port)
+{
+ enum tcpm_state prev_state;
+
+ mutex_lock(&port->lock);
+ port->state_machine_running = true;
+
+ if (port->queued_message && tcpm_send_queued_message(port))
+ goto done;
+
+ /* If we were queued due to a delayed state change, update it now */
+ if (port->delayed_state) {
+ dev_dbg(port->dev, "TCPM: state change %s -> %s [delayed %ld
ms]\n",
+ tcpm_states[port->state],
+ tcpm_states[port->delayed_state], port->delay_ms);
+ port->prev_state = port->state;
+ port->state = port->delayed_state;
+ port->delayed_state = INVALID_STATE;
+ }
+
+ /*
+ * Continue running as long as we have (non-delayed) state changes
+ * to make.
+ */
+ do {
+ prev_state = port->state;
+ run_state_machine(port);
+ if (port->queued_message)
+ tcpm_send_queued_message(port);
+ } while (port->state != prev_state && !port->delayed_state);
+
+done:
+ port->state_machine_running = false;
+ mutex_unlock(&port->lock);
+}
+
+static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
+ enum typec_cc_status cc2)
+{
+ enum typec_cc_status old_cc1, old_cc2;
+ enum tcpm_state new_state;
+
+ old_cc1 = port->cc1;
+ old_cc2 = port->cc2;
+ port->cc1 = cc1;
+ port->cc2 = cc2;
+
+ dev_dbg(port->dev, "TCPM: CC1: %u -> %u, CC2: %u -> %u [state %s,
polarity %d, %s]\n",
+ old_cc1, cc1, old_cc2, cc2, tcpm_states[port->state],
+ port->polarity,
+ tcpm_port_is_disconnected(port) ? "disconnected" : "connected");
+
+ switch (port->state) {
+ case TOGGLING:
+ if (tcpm_port_is_source(port))
+ tcpm_set_state(port, SRC_ATTACH_WAIT, 0);
+ else if (tcpm_port_is_sink(port))
+ tcpm_set_state(port, SNK_ATTACH_WAIT, 0);
+ break;
+ case SRC_UNATTACHED:
+ case SRC_ATTACH_WAIT:
+ if (tcpm_port_is_disconnected(port))
+ tcpm_set_state(port, SRC_UNATTACHED, 0);
+ else if (cc1 != old_cc1 || cc2 != old_cc2)
+ tcpm_set_state(port, SRC_ATTACH_WAIT, 0);
+ break;
+ case SRC_ATTACHED:
+ case SRC_SEND_CAPABILITIES:
+ case SRC_READY:
+ if (tcpm_port_is_disconnected(port) ||
+ !tcpm_port_is_source(port))
+ tcpm_set_state(port, SRC_UNATTACHED, 0);
+ break;
+ case SNK_UNATTACHED:
+ if (tcpm_port_is_sink(port))
+ tcpm_set_state(port, SNK_ATTACH_WAIT, 0);
+ break;
+ case SNK_ATTACH_WAIT:
+ if ((port->cc1 == TYPEC_CC_OPEN &&
+ port->cc2 != TYPEC_CC_OPEN) ||
+ (port->cc1 != TYPEC_CC_OPEN &&
+ port->cc2 == TYPEC_CC_OPEN))
+ new_state = SNK_DEBOUNCED;
+ else if (tcpm_port_is_disconnected(port))
+ new_state = SNK_UNATTACHED;
+ else
+ break;
+ if (new_state != port->delayed_state)
+ tcpm_set_state(port, SNK_ATTACH_WAIT, 0);
+ break;
+ case SNK_DEBOUNCED:
+ if (tcpm_port_is_disconnected(port))
+ new_state = SNK_UNATTACHED;
+ else if (port->vbus_present)
+ new_state = tcpm_try_src(port) ? INVALID_STATE :
SNK_ATTACHED;
+ else
+ new_state = SNK_UNATTACHED;
+ if (new_state != port->delayed_state)
+ tcpm_set_state(port, SNK_DEBOUNCED, 0);
+ break;
+ case SNK_READY:
+ if (tcpm_port_is_disconnected(port))
+ tcpm_set_state(port, unattached_state(port), 0);
+ else if (!port->pd_capable &&
+ (cc1 != old_cc1 || cc2 != old_cc2))
+ tcpm_set_current_limit(port,
+ tcpm_get_current_limit(port),
+ 5000);
+ break;
+
+ case SNK_DISCOVERY:
+ /* CC line is unstable, wait for debounce */
+ if (tcpm_port_is_disconnected(port))
+ tcpm_set_state(port, SNK_DISCOVERY_DEBOUNCE, 0);
+ break;
+ case SNK_DISCOVERY_DEBOUNCE:
+ break;
+
+ case PORT_RESET:
+ case PORT_RESET_WAIT_OFF:
+ /*
+ * State set back to default mode once the timer completes.
+ * Ignore CC changes here.
+ */
+ break;
+ default:
+ /*
+ * While acting as sink and auto vbus discharge is enabled,
Allow disconnect
+ * to be driven by vbus disconnect.
+ */
+ if (tcpm_port_is_disconnected(port))
+ tcpm_set_state(port, unattached_state(port), 0);
+ break;
+ }
+}
+
+static void _tcpm_pd_vbus_on(struct tcpm_port *port)
+{
+ dev_dbg(port->dev, "TCPM: VBUS on event\n");
+ port->vbus_present = true;
+ /*
+ * When vbus_present is true i.e. Voltage at VBUS is greater than
VSAFE5V implicitly
+ * states that vbus is not at VSAFE0V, hence clear the vbus_vsafe0v
flag here.
+ */
+ port->vbus_vsafe0v = false;
+
+ switch (port->state) {
+ case SNK_TRANSITION_SINK_VBUS:
+ port->explicit_contract = true;
+ tcpm_set_state(port, SNK_READY, 0);
+ break;
+ case SNK_DISCOVERY:
+ tcpm_set_state(port, SNK_DISCOVERY, 0);
+ break;
+ case SNK_DEBOUNCED:
+ tcpm_set_state(port, SNK_ATTACHED, 0);
+ break;
+ case SNK_HARD_RESET_WAIT_VBUS:
+ tcpm_set_state(port, SNK_HARD_RESET_SINK_ON, 0);
+ break;
+ case SRC_ATTACHED:
+ tcpm_set_state(port, SRC_STARTUP, 0);
+ break;
+ case SRC_HARD_RESET_VBUS_ON:
+ tcpm_set_state(port, SRC_STARTUP, 0);
+ break;
+
+ case PORT_RESET:
+ case PORT_RESET_WAIT_OFF:
+ /*
+ * State set back to default mode once the timer completes.
+ * Ignore vbus changes here.
+ */
+ break;
+
+ default:
+ break;
+ }
+}
+
+static void _tcpm_pd_vbus_off(struct tcpm_port *port)
+{
+ dev_dbg(port->dev, "TCPM: VBUS off event\n");
+ port->vbus_present = false;
+ port->vbus_never_low = false;
+ switch (port->state) {
+ case SNK_HARD_RESET_SINK_OFF:
+ tcpm_set_state(port, SNK_HARD_RESET_WAIT_VBUS, 0);
+ break;
+ case HARD_RESET_SEND:
+ break;
+ case SNK_ATTACH_WAIT:
+ tcpm_set_state(port, SNK_UNATTACHED, 0);
+ break;
+
+ case SNK_NEGOTIATE_CAPABILITIES:
+ break;
+
+ case PORT_RESET_WAIT_OFF:
+ tcpm_set_state(port, tcpm_default_state(port), 0);
+ break;
+
+ case PORT_RESET:
+ /*
+ * State set back to default mode once the timer completes.
+ * Ignore vbus changes here.
+ */
+ break;
+
+ default:
+ if (port->pwr_role == TYPEC_SINK && port->attached)
+ tcpm_set_state(port, SNK_UNATTACHED, 0);
+ break;
+ }
+}
+
+static void _tcpm_pd_hard_reset(struct tcpm_port *port)
+{
+ dev_dbg(port->dev, "TCPM: Received hard reset\n");
+ port->poll_event_cnt = 0;
+
+ /* If a hard reset message is received during the port reset process,
+ * we should ignore it, that is, do not set port->state to
HARD_RESET_START.
+ */
+ if (port->state == PORT_RESET || port->state == PORT_RESET_WAIT_OFF)
+ return;
+
+ /*
+ * If we keep receiving hard reset requests, executing the hard reset
+ * must have failed. Revert to error recovery if that happens.
+ */
+ tcpm_set_state(port,
+ port->hard_reset_count < PD_N_HARD_RESET_COUNT ?
+ HARD_RESET_START : ERROR_RECOVERY,
+ 0);
+}
+
+void tcpm_cc_change(struct tcpm_port *port)
+{
+ enum typec_cc_status cc1, cc2;
+
+ port->poll_event_cnt = 0;
+ if (port->tcpc->get_cc(port->tcpc, &cc1, &cc2) == 0)
+ _tcpm_cc_change(port, cc1, cc2);
+}
+EXPORT_SYMBOL_GPL(tcpm_cc_change);
+
+void tcpm_vbus_change(struct tcpm_port *port)
+{
+ bool vbus;
+
+ port->poll_event_cnt = 0;
+ vbus = port->tcpc->get_vbus(port->tcpc);
+ if (vbus)
+ _tcpm_pd_vbus_on(port);
+ else
+ _tcpm_pd_vbus_off(port);
+}
+EXPORT_SYMBOL_GPL(tcpm_vbus_change);
+
+void tcpm_pd_hard_reset(struct tcpm_port *port)
+{
+ port->poll_event_cnt = 0;
+ _tcpm_pd_hard_reset(port);
+}
+EXPORT_SYMBOL_GPL(tcpm_pd_hard_reset);
+
+static void tcpm_init(struct tcpm_port *port)
+{
+ enum typec_cc_status cc1, cc2;
+
+ port->tcpc->init(port->tcpc);
+
+ tcpm_reset_port(port);
+
+ /*
+ * XXX
+ * Should possibly wait for VBUS to settle if it was enabled locally
+ * since tcpm_reset_port() will disable VBUS.
+ */
+ port->vbus_present = port->tcpc->get_vbus(port->tcpc);
+ if (port->vbus_present)
+ port->vbus_never_low = true;
+
+ /*
+ * 1. When vbus_present is true, voltage on VBUS is already at VSAFE5V.
+ * So implicitly vbus_vsafe0v = false.
+ *
+ * 2. When vbus_present is false and TCPC does NOT support querying
+ * vsafe0v status, then, it's best to assume vbus is at VSAFE0V i.e.
+ * vbus_vsafe0v is true.
+ *
+ * 3. When vbus_present is false and TCPC does support querying vsafe0v,
+ * then, query tcpc for vsafe0v status.
+ */
+ if (port->vbus_present)
+ port->vbus_vsafe0v = false;
+ else
+ port->vbus_vsafe0v = true;
+
+ tcpm_set_state(port, tcpm_default_state(port), 0);
+
+ if (port->tcpc->get_cc(port->tcpc, &cc1, &cc2) == 0)
+ _tcpm_cc_change(port, cc1, cc2);
+}
+
+static int tcpm_fw_get_caps(struct tcpm_port *port)
+{
+ const char *cap_str;
+ ofnode node = port->tcpc->connector_node;
+ int ret;
+ u32 mw;
+
+ cap_str = ofnode_read_string(node, "power-role");
+ if (!cap_str)
+ return -EINVAL;
+
+ if (!strcmp("dual", cap_str))
+ port->typec_type = TYPEC_PORT_DRP;
+ else if (!strcmp("source", cap_str))
+ port->typec_type = TYPEC_PORT_SRC;
+ else if (!strcmp("sink", cap_str))
+ port->typec_type = TYPEC_PORT_SNK;
+ else
+ return -EINVAL;
+
+ port->port_type = port->typec_type;
+
+ if (port->port_type == TYPEC_PORT_SNK)
+ goto sink;
+
+ /* Get source pdos */
+ ret = ofnode_read_size(node, "source-pdos") / sizeof(u32);
+ if (ret <= 0)
+ return -EINVAL;
+
+ port->nr_src_pdo = min(ret, PDO_MAX_OBJECTS);
+ ret = ofnode_read_u32_array(node, "source-pdos",
+ port->src_pdo, port->nr_src_pdo);
+ if (ret || tcpm_validate_caps(port, port->src_pdo, port->nr_src_pdo))
+ return -EINVAL;
+
+ if (port->port_type == TYPEC_PORT_SRC)
+ return 0;
+
+ /* Get the preferred power role for DRP */
+ cap_str = ofnode_read_string(node, "try-power-role");
+ if (!cap_str)
+ return -EINVAL;
+
+ if (!strcmp("sink", cap_str))
+ port->typec_prefer_role = TYPEC_SINK;
+ else if (!strcmp("source", cap_str))
+ port->typec_prefer_role = TYPEC_SOURCE;
+ else
+ return -EINVAL;
+
+ if (port->typec_prefer_role < 0)
+ return -EINVAL;
+sink:
+ /* Get sink pdos */
+ ret = ofnode_read_size(node, "sink-pdos") / sizeof(u32);
+ if (ret <= 0)
+ return -EINVAL;
+
+ port->nr_snk_pdo = min(ret, PDO_MAX_OBJECTS);
+ ret = ofnode_read_u32_array(node, "sink-pdos",
+ port->snk_pdo, port->nr_snk_pdo);
+ if (ret || tcpm_validate_caps(port, port->snk_pdo, port->nr_snk_pdo))
+ return -EINVAL;
+
+ if (ofnode_read_u32_array(node, "op-sink-microwatt", &mw, 1))
+ return -EINVAL;
+ port->operating_snk_mw = mw / 1000;
+
+ port->self_powered = ofnode_read_bool(node, "self-powered");
+
+ return 0;
+}
+
+struct tcpm_port *tcpm_port_init(struct udevice *dev, struct tcpc_dev *tcpc)
+{
+ struct tcpm_port *port;
+ int err;
+
+ if (!dev || !tcpc ||
+ !tcpc->get_vbus || !tcpc->set_cc || !tcpc->get_cc ||
+ !tcpc->set_polarity || !tcpc->set_vconn || !tcpc->set_vbus ||
+ !tcpc->set_pd_rx || !tcpc->set_roles || !tcpc->pd_transmit)
+ return ERR_PTR(-EINVAL);
+
+ port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+ if (!port)
+ return ERR_PTR(-ENOMEM);
+
+ port->dev = dev;
+ port->tcpc = tcpc;
+
+ err = tcpm_fw_get_caps(port);
+ if (err < 0) {
+ dev_err(dev, "TCPM: please check the dts config: %d\n", err);
+ return ERR_PTR(err);
+ }
+
+ port->try_role = port->typec_prefer_role;
+ port->port_type = port->typec_type;
+
+ tcpm_init(port);
+
+ dev_info(port->dev, "TCPM: init finished\n");
+
+ return port;
+}
+EXPORT_SYMBOL_GPL(tcpm_port_init);
+
+void tcpm_poll_event(struct tcpm_port *port)
+{
+ if (!port->tcpc->get_vbus(port->tcpc))
+ return;
+
+ while (port->poll_event_cnt < TCPM_POLL_EVENT_TIME_OUT) {
+ if (!port->wait_dr_swap_message &&
+ (port->state == SNK_READY || port->state == SRC_READY))
+ break;
+
+ port->tcpc->poll_event(port->tcpc);
+ port->poll_event_cnt++;
+ udelay(500);
+ tcpm_check_and_run_delayed_work(port);
+ }
+
+ if (port->state != SNK_READY && port->state != SRC_READY)
+ dev_warn(port->dev, "TCPM: exit in state %s\n",
+ tcpm_states[port->state]);
+
+ /*
+ * At this time, call the callback function of the respective pd chip
+ * to enter the low-power mode. In order to reduce the time spent on
+ * the PD chip driver as much as possible, the tcpm framework does not
+ * fully process the communication initiated by the device,so it should
+ * be noted that we can disable the internal oscillator, etc., but do
+ * not turn off the power of the transceiver module, otherwise the
+ * self-powered Type-C device will initiate a Message(eg: self-powered
+ * Type-C hub initiates a SINK capability request(PD_CTRL_GET_SINK_CAP))
+ * and the pd chip cannot reply to GoodCRC, causing the self-powered
Type-C
+ * device to switch vbus to vSafe5v, or even turn off vbus.
+ */
+ if (port->tcpc->enter_low_power_mode) {
+ if (port->tcpc->enter_low_power_mode(port->tcpc,
+ port->attached,
+ port->pd_capable))
+ dev_err(port->dev, "TCPM: failed to enter low power\n");
+ else
+ dev_info(port->dev, "TCPM: PD chip enter low power
mode\n");
+ }
+}
+EXPORT_SYMBOL_GPL(tcpm_poll_event);
+
+int tcpm_get_voltage(struct tcpm_port *port)
+{
+ return port->supply_voltage;
+}
+EXPORT_SYMBOL_GPL(tcpm_get_voltage);
+
+int tcpm_get_current(struct tcpm_port *port)
+{
+ return port->current_limit;
+}
+EXPORT_SYMBOL_GPL(tcpm_get_voltage);
+
+const char *tcpm_get_state(struct tcpm_port *port)
+{
+ return tcpm_states[port->state];
+}
+EXPORT_SYMBOL_GPL(tcpm_get_state);
+
+int tcpm_get(const char *name, struct udevice **devp)
+{
+ return uclass_get_device_by_name(UCLASS_TCPM, name, devp);
+}
+
+int tcpm_print_info(struct udevice *dev)
+{
+ const struct dm_tcpm_ops *ops = dev_get_driver_ops(dev);
+
+ if (!ops)
+ return -ENOSYS;
+
+ if (ops->get_state)
+ printf("TCPM State: %s\n", ops->get_state(dev));
+
+ if (ops->get_voltage) {
+ int mv = ops->get_voltage(dev);
+
+ printf("Voltage: %2d.%03d V\n", mv / 1000, mv % 1000);
+ }
+
+ if (ops->get_current) {
+ int ma = ops->get_current(dev);
+
+ printf("Current: %2d.%03d A\n", ma / 1000, ma % 1000);
+ }
+
+ return 0;
+}
+
+UCLASS_DRIVER(tcpm) = {
+ .id = UCLASS_TCPM,
+ .name = "tcpm",
+};
diff --git a/include/dm/uclass-id.h b/include/dm/uclass-id.h
index 5271e646bb16..270088ad94f7 100644
--- a/include/dm/uclass-id.h
+++ b/include/dm/uclass-id.h
@@ -139,6 +139,7 @@ enum uclass_id {
UCLASS_SYSCON, /* System configuration device */
UCLASS_SYSINFO, /* Device information from hardware */
UCLASS_SYSRESET, /* System reset device */
+ UCLASS_TCPM, /* TypeC port manager */
UCLASS_TEE, /* Trusted Execution Environment device */
UCLASS_THERMAL, /* Thermal sensor */
UCLASS_TIMER, /* Timer device */
diff --git a/include/usb/pd.h b/include/usb/pd.h
new file mode 100644
index 000000000000..cacda322d7c6
--- /dev/null
+++ b/include/usb/pd.h
@@ -0,0 +1,516 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright 2015-2017 Google, Inc
+ */
+
+#ifndef __LINUX_USB_PD_H
+#define __LINUX_USB_PD_H
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+
+enum typec_port_type {
+ TYPEC_PORT_SRC,
+ TYPEC_PORT_SNK,
+ TYPEC_PORT_DRP,
+};
+
+enum typec_data_role {
+ TYPEC_DEVICE,
+ TYPEC_HOST,
+};
+
+enum typec_role {
+ TYPEC_SINK,
+ TYPEC_SOURCE,
+};
+
+/* USB PD Messages */
+enum pd_ctrl_msg_type {
+ /* 0 Reserved */
+ PD_CTRL_GOOD_CRC = 1,
+ PD_CTRL_GOTO_MIN = 2,
+ PD_CTRL_ACCEPT = 3,
+ PD_CTRL_REJECT = 4,
+ PD_CTRL_PING = 5,
+ PD_CTRL_PS_RDY = 6,
+ PD_CTRL_GET_SOURCE_CAP = 7,
+ PD_CTRL_GET_SINK_CAP = 8,
+ PD_CTRL_DR_SWAP = 9,
+ PD_CTRL_PR_SWAP = 10,
+ PD_CTRL_VCONN_SWAP = 11,
+ PD_CTRL_WAIT = 12,
+ PD_CTRL_SOFT_RESET = 13,
+ /* 14-15 Reserved */
+ PD_CTRL_NOT_SUPP = 16,
+ PD_CTRL_GET_SOURCE_CAP_EXT = 17,
+ PD_CTRL_GET_STATUS = 18,
+ PD_CTRL_FR_SWAP = 19,
+ PD_CTRL_GET_PPS_STATUS = 20,
+ PD_CTRL_GET_COUNTRY_CODES = 21,
+ /* 22-31 Reserved */
+};
+
+enum pd_data_msg_type {
+ /* 0 Reserved */
+ PD_DATA_SOURCE_CAP = 1,
+ PD_DATA_REQUEST = 2,
+ PD_DATA_BIST = 3,
+ PD_DATA_SINK_CAP = 4,
+ PD_DATA_BATT_STATUS = 5,
+ PD_DATA_ALERT = 6,
+ PD_DATA_GET_COUNTRY_INFO = 7,
+ PD_DATA_ENTER_USB = 8,
+ /* 9-14 Reserved */
+ PD_DATA_VENDOR_DEF = 15,
+ /* 16-31 Reserved */
+};
+
+enum pd_ext_msg_type {
+ /* 0 Reserved */
+ PD_EXT_SOURCE_CAP_EXT = 1,
+ PD_EXT_STATUS = 2,
+ PD_EXT_GET_BATT_CAP = 3,
+ PD_EXT_GET_BATT_STATUS = 4,
+ PD_EXT_BATT_CAP = 5,
+ PD_EXT_GET_MANUFACTURER_INFO = 6,
+ PD_EXT_MANUFACTURER_INFO = 7,
+ PD_EXT_SECURITY_REQUEST = 8,
+ PD_EXT_SECURITY_RESPONSE = 9,
+ PD_EXT_FW_UPDATE_REQUEST = 10,
+ PD_EXT_FW_UPDATE_RESPONSE = 11,
+ PD_EXT_PPS_STATUS = 12,
+ PD_EXT_COUNTRY_INFO = 13,
+ PD_EXT_COUNTRY_CODES = 14,
+ /* 15-31 Reserved */
+};
+
+#define PD_REV10 0x0
+#define PD_REV20 0x1
+#define PD_REV30 0x2
+#define PD_MAX_REV PD_REV30
+
+#define PD_HEADER_EXT_HDR BIT(15)
+#define PD_HEADER_CNT_SHIFT 12
+#define PD_HEADER_CNT_MASK 0x7
+#define PD_HEADER_ID_SHIFT 9
+#define PD_HEADER_ID_MASK 0x7
+#define PD_HEADER_PWR_ROLE BIT(8)
+#define PD_HEADER_REV_SHIFT 6
+#define PD_HEADER_REV_MASK 0x3
+#define PD_HEADER_DATA_ROLE BIT(5)
+#define PD_HEADER_TYPE_SHIFT 0
+#define PD_HEADER_TYPE_MASK 0x1f
+
+#define PD_HEADER(type, pwr, data, rev, id, cnt, ext_hdr) \
+ ((((type) & PD_HEADER_TYPE_MASK) << PD_HEADER_TYPE_SHIFT) | \
+ ((pwr) == TYPEC_SOURCE ? PD_HEADER_PWR_ROLE : 0) | \
+ ((data) == TYPEC_HOST ? PD_HEADER_DATA_ROLE : 0) | \
+ ((rev) << PD_HEADER_REV_SHIFT) |
\
+ (((id) & PD_HEADER_ID_MASK) << PD_HEADER_ID_SHIFT) | \
+ (((cnt) & PD_HEADER_CNT_MASK) << PD_HEADER_CNT_SHIFT) | \
+ ((ext_hdr) ? PD_HEADER_EXT_HDR : 0))
+
+#define PD_HEADER_LE(type, pwr, data, rev, id, cnt) \
+ cpu_to_le16(PD_HEADER((type), (pwr), (data), (rev), (id), (cnt), (0)))
+
+static inline unsigned int pd_header_cnt(u16 header)
+{
+ return (header >> PD_HEADER_CNT_SHIFT) & PD_HEADER_CNT_MASK;
+}
+
+static inline unsigned int pd_header_cnt_le(__le16 header)
+{
+ return pd_header_cnt(le16_to_cpu(header));
+}
+
+static inline unsigned int pd_header_type(u16 header)
+{
+ return (header >> PD_HEADER_TYPE_SHIFT) & PD_HEADER_TYPE_MASK;
+}
+
+static inline unsigned int pd_header_type_le(__le16 header)
+{
+ return pd_header_type(le16_to_cpu(header));
+}
+
+static inline unsigned int pd_header_msgid(u16 header)
+{
+ return (header >> PD_HEADER_ID_SHIFT) & PD_HEADER_ID_MASK;
+}
+
+static inline unsigned int pd_header_msgid_le(__le16 header)
+{
+ return pd_header_msgid(le16_to_cpu(header));
+}
+
+static inline unsigned int pd_header_rev(u16 header)
+{
+ return (header >> PD_HEADER_REV_SHIFT) & PD_HEADER_REV_MASK;
+}
+
+static inline unsigned int pd_header_rev_le(__le16 header)
+{
+ return pd_header_rev(le16_to_cpu(header));
+}
+
+#define PD_EXT_HDR_CHUNKED BIT(15)
+#define PD_EXT_HDR_CHUNK_NUM_SHIFT 11
+#define PD_EXT_HDR_CHUNK_NUM_MASK 0xf
+#define PD_EXT_HDR_REQ_CHUNK BIT(10)
+#define PD_EXT_HDR_DATA_SIZE_SHIFT 0
+#define PD_EXT_HDR_DATA_SIZE_MASK 0x1ff
+
+#define PD_EXT_HDR(data_size, req_chunk, chunk_num, chunked)
\
+ ((((data_size) & PD_EXT_HDR_DATA_SIZE_MASK) <<
PD_EXT_HDR_DATA_SIZE_SHIFT) | \
+ ((req_chunk) ? PD_EXT_HDR_REQ_CHUNK : 0) |
\
+ (((chunk_num) & PD_EXT_HDR_CHUNK_NUM_MASK) <<
PD_EXT_HDR_CHUNK_NUM_SHIFT) | \
+ ((chunked) ? PD_EXT_HDR_CHUNKED : 0))
+
+#define PD_EXT_HDR_LE(data_size, req_chunk, chunk_num, chunked) \
+ cpu_to_le16(PD_EXT_HDR((data_size), (req_chunk), (chunk_num),
(chunked)))
+
+static inline unsigned int pd_ext_header_chunk_num(u16 ext_header)
+{
+ return (ext_header >> PD_EXT_HDR_CHUNK_NUM_SHIFT) &
+ PD_EXT_HDR_CHUNK_NUM_MASK;
+}
+
+static inline unsigned int pd_ext_header_data_size(u16 ext_header)
+{
+ return (ext_header >> PD_EXT_HDR_DATA_SIZE_SHIFT) &
+ PD_EXT_HDR_DATA_SIZE_MASK;
+}
+
+static inline unsigned int pd_ext_header_data_size_le(__le16 ext_header)
+{
+ return pd_ext_header_data_size(le16_to_cpu(ext_header));
+}
+
+#define PD_MAX_PAYLOAD 7
+#define PD_EXT_MAX_CHUNK_DATA 26
+
+/*
+ * struct pd_chunked_ext_message_data - PD chunked extended message data as
+ * seen on wire
+ * @header: PD extended message header
+ * @data: PD extended message data
+ */
+struct pd_chunked_ext_message_data {
+ __le16 header;
+ u8 data[PD_EXT_MAX_CHUNK_DATA];
+} __packed;
+
+/*
+ * struct pd_message - PD message as seen on wire
+ * @header: PD message header
+ * @payload: PD message payload
+ * @ext_msg: PD message chunked extended message data
+ */
+struct pd_message {
+ __le16 header;
+ union {
+ __le32 payload[PD_MAX_PAYLOAD];
+ struct pd_chunked_ext_message_data ext_msg;
+ };
+} __packed;
+
+/* PDO: Power Data Object */
+#define PDO_MAX_OBJECTS 7
+
+enum pd_pdo_type {
+ PDO_TYPE_FIXED = 0,
+ PDO_TYPE_BATT = 1,
+ PDO_TYPE_VAR = 2,
+ PDO_TYPE_APDO = 3,
+};
+
+#define PDO_TYPE_SHIFT 30
+#define PDO_TYPE_MASK 0x3
+
+#define PDO_TYPE(t) ((t) << PDO_TYPE_SHIFT)
+
+#define PDO_VOLT_MASK 0x3ff
+#define PDO_CURR_MASK 0x3ff
+#define PDO_PWR_MASK 0x3ff
+
+#define PDO_FIXED_DUAL_ROLE BIT(29) /* Power role swap supported */
+#define PDO_FIXED_SUSPEND BIT(28) /* USB Suspend supported
(Source) */
+#define PDO_FIXED_HIGHER_CAP BIT(28) /* Requires more than vSafe5V
(Sink) */
+#define PDO_FIXED_EXTPOWER BIT(27) /* Externally powered */
+#define PDO_FIXED_USB_COMM BIT(26) /* USB communications capable */
+#define PDO_FIXED_DATA_SWAP BIT(25) /* Data role swap supported */
+#define PDO_FIXED_UNCHUNK_EXT BIT(24) /* Unchunked Extended Message
supported (Source) */
+#define PDO_FIXED_FRS_CURR_MASK (BIT(24) | BIT(23)) /* FR_Swap
Current (Sink) */
+#define PDO_FIXED_FRS_CURR_SHIFT 23
+#define PDO_FIXED_VOLT_SHIFT 10 /* 50mV units */
+#define PDO_FIXED_CURR_SHIFT 0 /* 10mA units */
+
+#define PDO_FIXED_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) <<
PDO_FIXED_VOLT_SHIFT)
+#define PDO_FIXED_CURR(ma) ((((ma) / 10) & PDO_CURR_MASK) <<
PDO_FIXED_CURR_SHIFT)
+
+#define PDO_FIXED(mv, ma, flags) \
+ (PDO_TYPE(PDO_TYPE_FIXED) | (flags) | \
+ PDO_FIXED_VOLT(mv) | PDO_FIXED_CURR(ma))
+
+#define VSAFE5V 5000 /* mv units */
+
+#define PDO_BATT_MAX_VOLT_SHIFT 20 /* 50mV units */
+#define PDO_BATT_MIN_VOLT_SHIFT 10 /* 50mV units */
+#define PDO_BATT_MAX_PWR_SHIFT 0 /* 250mW units */
+
+#define PDO_BATT_MIN_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) <<
PDO_BATT_MIN_VOLT_SHIFT)
+#define PDO_BATT_MAX_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) <<
PDO_BATT_MAX_VOLT_SHIFT)
+#define PDO_BATT_MAX_POWER(mw) ((((mw) / 250) & PDO_PWR_MASK) <<
PDO_BATT_MAX_PWR_SHIFT)
+
+#define PDO_BATT(min_mv, max_mv, max_mw) \
+ (PDO_TYPE(PDO_TYPE_BATT) | PDO_BATT_MIN_VOLT(min_mv) | \
+ PDO_BATT_MAX_VOLT(max_mv) | PDO_BATT_MAX_POWER(max_mw))
+
+#define PDO_VAR_MAX_VOLT_SHIFT 20 /* 50mV units */
+#define PDO_VAR_MIN_VOLT_SHIFT 10 /* 50mV units */
+#define PDO_VAR_MAX_CURR_SHIFT 0 /* 10mA units */
+
+#define PDO_VAR_MIN_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) <<
PDO_VAR_MIN_VOLT_SHIFT)
+#define PDO_VAR_MAX_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) <<
PDO_VAR_MAX_VOLT_SHIFT)
+#define PDO_VAR_MAX_CURR(ma) ((((ma) / 10) & PDO_CURR_MASK) <<
PDO_VAR_MAX_CURR_SHIFT)
+
+#define PDO_VAR(min_mv, max_mv, max_ma) \
+ (PDO_TYPE(PDO_TYPE_VAR) | PDO_VAR_MIN_VOLT(min_mv) | \
+ PDO_VAR_MAX_VOLT(max_mv) | PDO_VAR_MAX_CURR(max_ma))
+
+enum pd_apdo_type {
+ APDO_TYPE_PPS = 0,
+};
+
+#define PDO_APDO_TYPE_SHIFT 28 /* Only valid value currently is 0x0 -
PPS */
+#define PDO_APDO_TYPE_MASK 0x3
+
+#define PDO_APDO_TYPE(t) ((t) << PDO_APDO_TYPE_SHIFT)
+
+#define PDO_PPS_APDO_MAX_VOLT_SHIFT 17 /* 100mV units */
+#define PDO_PPS_APDO_MIN_VOLT_SHIFT 8 /* 100mV units */
+#define PDO_PPS_APDO_MAX_CURR_SHIFT 0 /* 50mA units */
+
+#define PDO_PPS_APDO_VOLT_MASK 0xff
+#define PDO_PPS_APDO_CURR_MASK 0x7f
+
+#define PDO_PPS_APDO_MIN_VOLT(mv) \
+ ((((mv) / 100) & PDO_PPS_APDO_VOLT_MASK) << PDO_PPS_APDO_MIN_VOLT_SHIFT)
+#define PDO_PPS_APDO_MAX_VOLT(mv) \
+ ((((mv) / 100) & PDO_PPS_APDO_VOLT_MASK) << PDO_PPS_APDO_MAX_VOLT_SHIFT)
+#define PDO_PPS_APDO_MAX_CURR(ma) \
+ ((((ma) / 50) & PDO_PPS_APDO_CURR_MASK) << PDO_PPS_APDO_MAX_CURR_SHIFT)
+
+#define PDO_PPS_APDO(min_mv, max_mv, max_ma) \
+ (PDO_TYPE(PDO_TYPE_APDO) | PDO_APDO_TYPE(APDO_TYPE_PPS) | \
+ PDO_PPS_APDO_MIN_VOLT(min_mv) | PDO_PPS_APDO_MAX_VOLT(max_mv) | \
+ PDO_PPS_APDO_MAX_CURR(max_ma))
+
+static inline enum pd_pdo_type pdo_type(u32 pdo)
+{
+ return (pdo >> PDO_TYPE_SHIFT) & PDO_TYPE_MASK;
+}
+
+static inline unsigned int pdo_fixed_voltage(u32 pdo)
+{
+ return ((pdo >> PDO_FIXED_VOLT_SHIFT) & PDO_VOLT_MASK) * 50;
+}
+
+static inline unsigned int pdo_min_voltage(u32 pdo)
+{
+ return ((pdo >> PDO_VAR_MIN_VOLT_SHIFT) & PDO_VOLT_MASK) * 50;
+}
+
+static inline unsigned int pdo_max_voltage(u32 pdo)
+{
+ return ((pdo >> PDO_VAR_MAX_VOLT_SHIFT) & PDO_VOLT_MASK) * 50;
+}
+
+static inline unsigned int pdo_max_current(u32 pdo)
+{
+ return ((pdo >> PDO_VAR_MAX_CURR_SHIFT) & PDO_CURR_MASK) * 10;
+}
+
+static inline unsigned int pdo_max_power(u32 pdo)
+{
+ return ((pdo >> PDO_BATT_MAX_PWR_SHIFT) & PDO_PWR_MASK) * 250;
+}
+
+static inline enum pd_apdo_type pdo_apdo_type(u32 pdo)
+{
+ return (pdo >> PDO_APDO_TYPE_SHIFT) & PDO_APDO_TYPE_MASK;
+}
+
+static inline unsigned int pdo_pps_apdo_min_voltage(u32 pdo)
+{
+ return ((pdo >> PDO_PPS_APDO_MIN_VOLT_SHIFT) &
+ PDO_PPS_APDO_VOLT_MASK) * 100;
+}
+
+static inline unsigned int pdo_pps_apdo_max_voltage(u32 pdo)
+{
+ return ((pdo >> PDO_PPS_APDO_MAX_VOLT_SHIFT) &
+ PDO_PPS_APDO_VOLT_MASK) * 100;
+}
+
+static inline unsigned int pdo_pps_apdo_max_current(u32 pdo)
+{
+ return ((pdo >> PDO_PPS_APDO_MAX_CURR_SHIFT) &
+ PDO_PPS_APDO_CURR_MASK) * 50;
+}
+
+/* RDO: Request Data Object */
+#define RDO_OBJ_POS_SHIFT 28
+#define RDO_OBJ_POS_MASK 0x7
+#define RDO_GIVE_BACK BIT(27) /* Supports reduced operating current */
+#define RDO_CAP_MISMATCH BIT(26) /* Not satisfied by source caps */
+#define RDO_USB_COMM BIT(25) /* USB communications capable */
+#define RDO_NO_SUSPEND BIT(24) /* USB Suspend not supported */
+
+#define RDO_PWR_MASK 0x3ff
+#define RDO_CURR_MASK 0x3ff
+
+#define RDO_FIXED_OP_CURR_SHIFT 10
+#define RDO_FIXED_MAX_CURR_SHIFT 0
+
+#define RDO_OBJ(idx) (((idx) & RDO_OBJ_POS_MASK) << RDO_OBJ_POS_SHIFT)
+
+#define PDO_FIXED_OP_CURR(ma) ((((ma) / 10) & RDO_CURR_MASK) <<
RDO_FIXED_OP_CURR_SHIFT)
+#define PDO_FIXED_MAX_CURR(ma) ((((ma) / 10) & RDO_CURR_MASK) <<
RDO_FIXED_MAX_CURR_SHIFT)
+
+#define RDO_FIXED(idx, op_ma, max_ma, flags) \
+ (RDO_OBJ(idx) | (flags) | \
+ PDO_FIXED_OP_CURR(op_ma) | PDO_FIXED_MAX_CURR(max_ma))
+
+#define RDO_BATT_OP_PWR_SHIFT 10 /* 250mW units */
+#define RDO_BATT_MAX_PWR_SHIFT 0 /* 250mW units */
+
+#define RDO_BATT_OP_PWR(mw) ((((mw) / 250) & RDO_PWR_MASK) <<
RDO_BATT_OP_PWR_SHIFT)
+#define RDO_BATT_MAX_PWR(mw) ((((mw) / 250) & RDO_PWR_MASK) <<
RDO_BATT_MAX_PWR_SHIFT)
+
+#define RDO_BATT(idx, op_mw, max_mw, flags) \
+ (RDO_OBJ(idx) | (flags) | \
+ RDO_BATT_OP_PWR(op_mw) | RDO_BATT_MAX_PWR(max_mw))
+
+#define RDO_PROG_VOLT_MASK 0x7ff
+#define RDO_PROG_CURR_MASK 0x7f
+
+#define RDO_PROG_VOLT_SHIFT 9
+#define RDO_PROG_CURR_SHIFT 0
+
+#define RDO_PROG_VOLT_MV_STEP 20
+#define RDO_PROG_CURR_MA_STEP 50
+
+#define PDO_PROG_OUT_VOLT(mv) \
+ ((((mv) / RDO_PROG_VOLT_MV_STEP) & RDO_PROG_VOLT_MASK) <<
RDO_PROG_VOLT_SHIFT)
+#define PDO_PROG_OP_CURR(ma) \
+ ((((ma) / RDO_PROG_CURR_MA_STEP) & RDO_PROG_CURR_MASK) <<
RDO_PROG_CURR_SHIFT)
+
+#define RDO_PROG(idx, out_mv, op_ma, flags) \
+ (RDO_OBJ(idx) | (flags) | \
+ PDO_PROG_OUT_VOLT(out_mv) | PDO_PROG_OP_CURR(op_ma))
+
+static inline unsigned int rdo_index(u32 rdo)
+{
+ return (rdo >> RDO_OBJ_POS_SHIFT) & RDO_OBJ_POS_MASK;
+}
+
+static inline unsigned int rdo_op_current(u32 rdo)
+{
+ return ((rdo >> RDO_FIXED_OP_CURR_SHIFT) & RDO_CURR_MASK) * 10;
+}
+
+static inline unsigned int rdo_max_current(u32 rdo)
+{
+ return ((rdo >> RDO_FIXED_MAX_CURR_SHIFT) &
+ RDO_CURR_MASK) * 10;
+}
+
+static inline unsigned int rdo_op_power(u32 rdo)
+{
+ return ((rdo >> RDO_BATT_OP_PWR_SHIFT) & RDO_PWR_MASK) * 250;
+}
+
+static inline unsigned int rdo_max_power(u32 rdo)
+{
+ return ((rdo >> RDO_BATT_MAX_PWR_SHIFT) & RDO_PWR_MASK) * 250;
+}
+
+/* Enter_USB Data Object */
+#define EUDO_USB_MODE_MASK GENMASK(30, 28)
+#define EUDO_USB_MODE_SHIFT 28
+#define EUDO_USB_MODE_USB2 0
+#define EUDO_USB_MODE_USB3 1
+#define EUDO_USB_MODE_USB4 2
+#define EUDO_USB4_DRD BIT(26)
+#define EUDO_USB3_DRD BIT(25)
+#define EUDO_CABLE_SPEED_MASK GENMASK(23, 21)
+#define EUDO_CABLE_SPEED_SHIFT 21
+#define EUDO_CABLE_SPEED_USB2 0
+#define EUDO_CABLE_SPEED_USB3_GEN1 1
+#define EUDO_CABLE_SPEED_USB4_GEN2 2
+#define EUDO_CABLE_SPEED_USB4_GEN3 3
+#define EUDO_CABLE_TYPE_MASK GENMASK(20, 19)
+#define EUDO_CABLE_TYPE_SHIFT 19
+#define EUDO_CABLE_TYPE_PASSIVE 0
+#define EUDO_CABLE_TYPE_RE_TIMER 1
+#define EUDO_CABLE_TYPE_RE_DRIVER 2
+#define EUDO_CABLE_TYPE_OPTICAL 3
+#define EUDO_CABLE_CURRENT_MASK GENMASK(18, 17)
+#define EUDO_CABLE_CURRENT_SHIFT 17
+#define EUDO_CABLE_CURRENT_NOTSUPP 0
+#define EUDO_CABLE_CURRENT_3A 2
+#define EUDO_CABLE_CURRENT_5A 3
+#define EUDO_PCIE_SUPPORT BIT(16)
+#define EUDO_DP_SUPPORT BIT(15)
+#define EUDO_TBT_SUPPORT BIT(14)
+#define EUDO_HOST_PRESENT BIT(13)
+
+/* USB PD timers and counters */
+#define PD_T_NO_RESPONSE 5000 /* 4.5 - 5.5 seconds */
+#define PD_T_DB_DETECT 10000 /* 10 - 15 seconds */
+#define PD_T_SEND_SOURCE_CAP 150 /* 100 - 200 ms */
+#define PD_T_SENDER_RESPONSE 60 /* 24 - 30 ms, relaxed */
+#define PD_T_RECEIVER_RESPONSE 15 /* 15ms max */
+#define PD_T_SOURCE_ACTIVITY 45
+#define PD_T_SINK_ACTIVITY 135
+#define PD_T_SINK_WAIT_CAP 310 /* 310 - 620 ms */
+#define PD_T_PS_TRANSITION 500
+#define PD_T_SRC_TRANSITION 35
+#define PD_T_DRP_SNK 40
+#define PD_T_DRP_SRC 30
+#define PD_T_PS_SOURCE_OFF 920
+#define PD_T_PS_SOURCE_ON 480
+#define PD_T_PS_SOURCE_ON_PRS 450 /* 390 - 480ms */
+#define PD_T_PS_HARD_RESET 30
+#define PD_T_SRC_RECOVER 760
+#define PD_T_SRC_RECOVER_MAX 1000
+#define PD_T_SRC_TURN_ON 275
+#define PD_T_SAFE_0V 650
+#define PD_T_VCONN_SOURCE_ON 100
+#define PD_T_SINK_REQUEST 100 /* 100 ms minimum */
+#define PD_T_ERROR_RECOVERY 100 /* minimum 25 is insufficient */
+#define PD_T_SRCSWAPSTDBY 625 /* Maximum of 650ms */
+#define PD_T_NEWSRC 250 /* Maximum of 275ms */
+#define PD_T_SWAP_SRC_START 20 /* Minimum of 20ms */
+#define PD_T_BIST_CONT_MODE 50 /* 30 - 60 ms */
+#define PD_T_SINK_TX 16 /* 16 - 20 ms */
+#define PD_T_CHUNK_NOT_SUPP 42 /* 40 - 50 ms */
+
+#define PD_T_DRP_TRY 100 /* 75 - 150 ms */
+#define PD_T_DRP_TRYWAIT 600 /* 400 - 800 ms */
+
+#define PD_T_CC_DEBOUNCE 200 /* 100 - 200 ms */
+#define PD_T_PD_DEBOUNCE 20 /* 10 - 20 ms */
+#define PD_T_TRY_CC_DEBOUNCE 15 /* 10 - 20 ms */
+
+#define PD_N_CAPS_COUNT (PD_T_NO_RESPONSE /
PD_T_SEND_SOURCE_CAP)
+#define PD_N_HARD_RESET_COUNT 1
+
+#define PD_P_SNK_STDBY_MW 2500 /* 2500 mW */
+
+/* Time to wait for TCPC to complete transmit */
+#define PD_T_TCPC_TX_TIMEOUT 100 /* in ms */
+
+#endif /* __LINUX_USB_PD_H */
diff --git a/include/usb/tcpm.h b/include/usb/tcpm.h
new file mode 100644
index 000000000000..740a245787f3
--- /dev/null
+++ b/include/usb/tcpm.h
@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright 2015-2017 Google, Inc
+ * Copyright 2024 Collabora
+ */
+
+#ifndef __LINUX_USB_TCPM_H
+#define __LINUX_USB_TCPM_H
+
+#include <dm/of.h>
+#include <linux/bitops.h>
+#include "pd.h"
+
+enum typec_cc_status {
+ TYPEC_CC_OPEN,
+ TYPEC_CC_RA,
+ TYPEC_CC_RD,
+ TYPEC_CC_RP_DEF,
+ TYPEC_CC_RP_1_5,
+ TYPEC_CC_RP_3_0,
+};
+
+enum typec_cc_polarity {
+ TYPEC_POLARITY_CC1,
+ TYPEC_POLARITY_CC2,
+};
+
+enum tcpm_transmit_status {
+ TCPC_TX_SUCCESS = 0,
+ TCPC_TX_DISCARDED = 1,
+ TCPC_TX_FAILED = 2,
+};
+
+enum tcpm_transmit_type {
+ TCPC_TX_SOP = 0,
+ TCPC_TX_SOP_PRIME = 1,
+ TCPC_TX_SOP_PRIME_PRIME = 2,
+ TCPC_TX_SOP_DEBUG_PRIME = 3,
+ TCPC_TX_SOP_DEBUG_PRIME_PRIME = 4,
+ TCPC_TX_HARD_RESET = 5,
+ TCPC_TX_CABLE_RESET = 6,
+ TCPC_TX_BIST_MODE_2 = 7
+};
+
+/**
+ * struct tcpc_dev - Port configuration and callback functions
+ * @fwnode: Pointer to port fwnode
+ * @get_vbus: Called to read current VBUS state
+ * @set_cc: Called to set value of CC pins
+ * @get_cc: Called to read current CC pin values
+ * @set_polarity:
+ * Called to set polarity
+ * @set_vconn: Called to enable or disable VCONN
+ * @set_vbus: Called to enable or disable VBUS
+ * @set_pd_rx: Called to enable or disable reception of PD messages
+ * @set_roles: Called to set power and data roles
+ * @start_toggling:
+ * Optional; if supported by hardware, called to start dual-role
+ * toggling or single-role connection detection. Toggling stops
+ * automatically if a connection is established.
+ * @pd_transmit:Called to transmit PD message
+ * @poll_event:
+ * After the PD chip driver is loaded, the callback function will
be
+ * called to poll what events have been triggered.
+ * @enter_low_power_mode:
+ * Optional; the pd chip enters low power mode.
+ */
+struct tcpc_dev {
+ ofnode connector_node;
+ int (*init)(struct tcpc_dev *dev);
+ int (*get_vbus)(struct tcpc_dev *dev);
+ int (*set_cc)(struct tcpc_dev *dev, enum typec_cc_status cc);
+ int (*get_cc)(struct tcpc_dev *dev, enum typec_cc_status *cc1,
+ enum typec_cc_status *cc2);
+ int (*set_polarity)(struct tcpc_dev *dev,
+ enum typec_cc_polarity polarity);
+ int (*set_vconn)(struct tcpc_dev *dev, bool on);
+ int (*set_vbus)(struct tcpc_dev *dev, bool on, bool charge);
+ int (*set_pd_rx)(struct tcpc_dev *dev, bool on);
+ int (*set_roles)(struct tcpc_dev *dev, bool attached,
+ enum typec_role role, enum typec_data_role data);
+ int (*start_toggling)(struct tcpc_dev *dev,
+ enum typec_port_type port_type,
+ enum typec_cc_status cc);
+ int (*pd_transmit)(struct tcpc_dev *dev, enum tcpm_transmit_type type,
+ const struct pd_message *msg, unsigned int
negotiated_rev);
+ void (*poll_event)(struct tcpc_dev *dev);
+ int (*enter_low_power_mode)(struct tcpc_dev *dev, bool attached, bool
pd_capable);
+};
+
+struct dm_tcpm_ops {
+ int (*get_voltage)(struct udevice *dev);
+ int (*get_current)(struct udevice *dev);
+ const char* (*get_state)(struct udevice *dev);
+};
+
+/* API for drivers */
+struct tcpm_port;
+struct tcpm_port *tcpm_port_init(struct udevice *dev, struct tcpc_dev *tcpc);
+void tcpm_poll_event(struct tcpm_port *port);
+void tcpm_vbus_change(struct tcpm_port *port);
+void tcpm_cc_change(struct tcpm_port *port);
+void tcpm_pd_receive(struct tcpm_port *port,
+ const struct pd_message *msg);
+void tcpm_pd_transmit_complete(struct tcpm_port *port,
+ enum tcpm_transmit_status status);
+void tcpm_pd_hard_reset(struct tcpm_port *port);
+int tcpm_get_current(struct tcpm_port *port);
+int tcpm_get_voltage(struct tcpm_port *port);
+const char *tcpm_get_state(struct tcpm_port *port);
+
+/* API for boards */
+int tcpm_get(const char *name, struct udevice **devp);
+int tcpm_print_info(struct udevice *devp);
+
+#endif /* __LINUX_USB_TCPM_H */
--
2.43.0
