[U-Boot] [PATCH] mx51evk: Make use of the i.MX GPIO API

[Fabio Estevam]

Make use of the i.MX GPIO API.

While at it created a separate function for the FEC PHY reset,
so that it can be decoupled from the power_init function.

Signed-off-by: Fabio Estevam <fabio.este...@freescale.com>
---
 board/freescale/mx51evk/mx51evk.c |   33 +++++++++++++++++----------------
 1 files changed, 17 insertions(+), 16 deletions(-)

diff --git a/board/freescale/mx51evk/mx51evk.c 
b/board/freescale/mx51evk/mx51evk.c
index ef7c6e4..2dabef9 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -33,6 +33,11 @@
 #include <fsl_esdhc.h>
 #include <fsl_pmic.h>
 #include <mc13892.h>
+#include <mxc_gpio.h>
+
+#define MX51EVK_PHY_RESET      (1 * 32 + 14)   /* GPIO2_14 */
+#define MX51EVK_SD1_CD         (0 * 32 + 0)    /* GPIO1_0 */
+#define MX51EVK_SD2_CD         (0 * 32 + 6)    /* GPIO1_6 */
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -261,27 +266,22 @@ static void power_init(void)
        pmic_reg_write(REG_MODE_1, val);
        udelay(200);
 
-       reg = readl(GPIO2_BASE_ADDR + 0x0);
-       reg &= ~0x4000;  /* Lower reset line */
-       writel(reg, GPIO2_BASE_ADDR + 0x0);
-
-       reg = readl(GPIO2_BASE_ADDR + 0x4);
-       reg |= 0x4000;  /* configure GPIO lines as output */
-       writel(reg, GPIO2_BASE_ADDR + 0x4);
-
-       /* Reset the ethernet controller over GPIO */
-       writel(0x1, IOMUXC_BASE_ADDR + 0x0AC);
-
        /* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
        val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
                VVIDEOEN | VAUDIOEN  | VSDEN;
        pmic_reg_write(REG_MODE_1, val);
+}
+
+static void reset_phy_fec(void)
+{
+       mxc_request_iomux(MX51_PIN_EIM_A20, IOMUX_CONFIG_ALT1);
+       mxc_gpio_direction(MX51EVK_PHY_RESET, MXC_GPIO_DIRECTION_OUT);
 
+       mxc_gpio_set(MX51EVK_PHY_RESET, 0);     /* Lower reset line */
+
        udelay(500);
 
-       reg = readl(GPIO2_BASE_ADDR + 0x0);
-       reg |= 0x4000;
-       writel(reg, GPIO2_BASE_ADDR + 0x0);
+       mxc_gpio_set(MX51EVK_PHY_RESET, 1);     /* Set reset line to high */
 }
 
 #ifdef CONFIG_FSL_ESDHC
@@ -290,9 +290,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
        struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 
        if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
-               *cd = readl(GPIO1_BASE_ADDR) & 0x01;
+               *cd = mxc_gpio_get(MX51EVK_SD1_CD);
        else
-               *cd = readl(GPIO1_BASE_ADDR) & 0x40;
+               *cd = mxc_gpio_get(MX51EVK_SD2_CD);
 
        return 0;
 }
@@ -414,6 +414,7 @@ int board_mmc_init(bd_t *bis)
 int board_early_init_f(void)
 {
        setup_iomux_uart();
+       reset_phy_fec();
        setup_iomux_fec();
 
        return 0;
-- 
1.6.0.4


_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot