Enable the command and the shim driver
Configure the pads to allow access to the button on GPIO_121 and the 2 LEDS on
GPIO_7 and GPIO_8
Signed-off-by: Joe Hershberger <joe.hershber...@ni.com>
Cc: Joe Hershberger <joe.hershber...@gmail.com>
Cc: Sandeep Paulraj <s-paul...@ti.com>
---
Changes for v2:
board/ti/panda/panda_mux_data.h | 6 +++---
include/configs/omap4_panda.h | 4 ++++
2 files changed, 7 insertions(+), 3 deletions(-)
diff --git a/board/ti/panda/panda_mux_data.h b/board/ti/panda/panda_mux_data.h
index 16cc0ad..4c9b57e 100644
--- a/board/ti/panda/panda_mux_data.h
+++ b/board/ti/panda/panda_mux_data.h
@@ -115,7 +115,7 @@ const struct pad_conf_entry
core_padconf_array_non_essential[] = {
{ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /*
abe_clks */
{ABE_DMIC_CLK1, (M0)}, /*
abe_dmic_clk1 */
{ABE_DMIC_DIN1, (IEN | M0)}, /*
abe_dmic_din1 */
- {ABE_DMIC_DIN2, (IEN | M0)}, /*
abe_dmic_din2 */
+ {ABE_DMIC_DIN2, (PTU | IEN | M3)}, /*
gpio_121 */
{ABE_DMIC_DIN3, (IEN | M0)}, /*
abe_dmic_din3 */
{UART2_CTS, (PTU | IEN | M0)}, /*
uart2_cts */
{UART2_RTS, (M0)}, /*
uart2_rts */
@@ -223,8 +223,8 @@ const struct pad_conf_entry
wkup_padconf_array_non_essential[] = {
{PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */
{PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */
{PAD1_FREF_CLK3_REQ, (M3)}, /* gpio_wk30 */
- {PAD1_FREF_CLK4_REQ, (M3)}, /* gpio_wk7 */
- {PAD0_FREF_CLK4_OUT, (M3)}, /* gpio_wk8 */
+ {PAD1_FREF_CLK4_REQ, (IEN | M3)}, /* gpio_wk7 */
+ {PAD0_FREF_CLK4_OUT, (IEN | M3)}, /* gpio_wk8 */
};
#endif /* _SDP4430_MUX_DATA_H */
diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h
index e313231..f890fc6 100644
--- a/include/configs/omap4_panda.h
+++ b/include/configs/omap4_panda.h
@@ -120,6 +120,10 @@
/* Flash */
#define CONFIG_SYS_NO_FLASH 1
+/* GPIO */
+#define CONFIG_OMAP_GPIO 1
+#define CONFIG_CMD_GPIO 1
+
/* commands to include */
#include <config_cmd_default.h>
--
1.6.0.2
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
