On Thu, Aug 25, 2011 at 8:25 PM, Marek Vasut <marek.va...@gmail.com> wrote: > > On Thursday, August 25, 2011 04:48:25 PM Balaji T K wrote: > > Config VMMC voltage to 3V for MMC/SD card slot > > and PBIAS settings needed for OMAP4 > > Fixes MMC/SD detection on boot from eMMC. > > > > Signed-off-by: Balaji T K <balaj...@ti.com> > > Signed-off-by: Aneesh V <ane...@ti.com> > > --- > > arch/arm/include/asm/arch-omap4/omap4.h | 1 + > > drivers/mmc/omap_hsmmc.c | 28 > > +++++++++++++++++++++++++--- drivers/power/twl6030.c | > > 7 +++++++ > > include/configs/omap4_sdp4430.h | 2 ++ > > include/twl6030.h | 3 +++ > > 5 files changed, 38 insertions(+), 3 deletions(-) > > > > diff --git a/arch/arm/include/asm/arch-omap4/omap4.h > > b/arch/arm/include/asm/arch-omap4/omap4.h index 9aad0e6..13fc8c9 100644 > > --- a/arch/arm/include/asm/arch-omap4/omap4.h > > +++ b/arch/arm/include/asm/arch-omap4/omap4.h > > @@ -55,6 +55,7 @@ > > #define LPDDR2_IO_REGS_BASE 0x4A100638 > > > > #define CONTROL_EFUSE_2 0x4A100704 > > +#define CONTROL_PBIASLITE 0x4A100600 > > Can't you use struct omap_something_regs { ... } like most of U-Boot code ?
Currently only these 3 registers are used in u-boot for this CONTROL module IP. Above 3 registers don't have such API with base address(0x4a100000) But I think there is a patch coming soon. Should this patch wait until then ? > > > > > /* CONTROL_ID_CODE */ > > #define CONTROL_ID_CODE 0x4A002204 > > diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c > > index 6627905..95bb661 100644 > > --- a/drivers/mmc/omap_hsmmc.c > > +++ b/drivers/mmc/omap_hsmmc.c > > @@ -28,6 +28,7 @@ > > #include <part.h> > > #include <i2c.h> > > #include <twl4030.h> > > +#include <twl6030.h> > > #include <asm/io.h> > > #include <asm/arch/mmc_host_def.h> > > #include <asm/arch/sys_proto.h> > > @@ -38,7 +39,24 @@ > > static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size); > > static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int > > siz); static struct mmc hsmmc_dev[2]; > > -unsigned char mmc_board_init(hsmmc_t *mmc_base) > > + > > +#if defined(CONFIG_OMAP44XX) && defined(CONFIG_TWL6030_POWER) > > +static void omap4_vmmc_pbias_config(struct mmc *mmc) > > +{ > > + u32 value = 0; > > + > > + value = readl(CONTROL_PBIASLITE); > > + value &= ~((1 << 22) | (1 << 26)); > > What's this magic ? > will use #define > > + writel(value, CONTROL_PBIASLITE); > > + /* set VMMC to 3V */ > > + twl6030_power_mmc_init(); > > + value = readl(CONTROL_PBIASLITE); > > + value |= (1 << 21) | (1 << 22) | (1 << 26); > > And this magic ? will use #define > > > + writel(value, CONTROL_PBIASLITE); > > +} > > +#endif > > + > > +unsigned char mmc_board_init(struct mmc *mmc) > > { > > #if defined(CONFIG_TWL4030_POWER) > > twl4030_power_mmc_init(); > > @@ -67,7 +85,11 @@ unsigned char mmc_board_init(hsmmc_t *mmc_base) > > &prcm_base->iclken1_core); > > #endif > > > > -/* TODO add appropriate OMAP4 init - none currently necessary */ > > +#if defined(CONFIG_OMAP44XX) && defined(CONFIG_TWL6030_POWER) > > + /* PBIAS config needed for MMC1 only */ > > You have == 0 below ... so you're numbering from 1 here ? It's a bit > confusing. uboot mmc starts numbering from 0, But OMAP data manual starts the IP numbering from 1 > > > + if (mmc->block_dev.dev == 0) > > + omap4_vmmc_pbias_config(mmc); > > +#endif > > > > return 0; > > } > > @@ -108,7 +130,7 @@ static int mmc_init_setup(struct mmc *mmc) > > unsigned int dsor; > > ulong start; > > > > - mmc_board_init(mmc_base); > > + mmc_board_init(mmc); > > Is this a bugfix ? I changed the prototype for checking mmc->block_dev.dev in mmc_board_init. Without this change, regulator to MMC is not set to correct voltage, MMC/SD fails to get detected. mmc_init fails and read/write also fails. > > > > > writel(readl(&mmc_base->sysconfig) | MMC_SOFTRESET, > > &mmc_base->sysconfig); > > diff --git a/drivers/power/twl6030.c b/drivers/power/twl6030.c > > index fef57b4..c5a0038 100644 > > --- a/drivers/power/twl6030.c > > +++ b/drivers/power/twl6030.c > > @@ -182,6 +182,13 @@ void twl6030_init_battery_charging(void) > > return; > > } > > > > +void twl6030_power_mmc_init() > > +{ > > + /* set voltage to 3.0 and turnon for APP */ > > + twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x15, VMMC_CFG_VOLTATE); > > + twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x21, VMMC_CFG_STATE); > > +} > > + > > void twl6030_usb_device_settings() > > { > > u8 data = 0; > > diff --git a/include/configs/omap4_sdp4430.h > > b/include/configs/omap4_sdp4430.h index 5b3110c..50797ab 100644 > > --- a/include/configs/omap4_sdp4430.h > > +++ b/include/configs/omap4_sdp4430.h > > @@ -98,8 +98,10 @@ > > #define CONFIG_I2C_MULTI_BUS 1 > > > > /* TWL6030 */ > > +#ifndef CONFIG_SPL_BUILD > > #define CONFIG_TWL6030_POWER 1 > > #define CONFIG_CMD_BAT 1 > > +#endif > > > > /* MMC */ > > #define CONFIG_GENERIC_MMC 1 > > diff --git a/include/twl6030.h b/include/twl6030.h > > index 6ed68a0..a9fcadb 100644 > > --- a/include/twl6030.h > > +++ b/include/twl6030.h > > @@ -33,6 +33,8 @@ > > #define TWL6030_CHIP_PWM 0x49 > > > > /* Slave Address 0x48 */ > > +#define VMMC_CFG_STATE 0x9A > > +#define VMMC_CFG_VOLTATE 0x9B > > #define VUSB_CFG_STATE 0xA2 > > > > #define MISC1 0xE4 > > @@ -130,3 +132,4 @@ void twl6030_start_usb_charging(void); > > void twl6030_stop_usb_charging(void); > > int twl6030_get_battery_voltage(void); > > int twl6030_get_battery_current(void); > > +void twl6030_power_mmc_init(void); > > Thanks! Cheers! _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot