From: Vikas Manocha <vikas.mano...@st.com>
If AN(auto-negotiation) is ON, speed bit of control register are not
applicable. Also phy registers were not getting programmed as per the
result of AN. This patch sets only AN bit & restart AN bit for AN ON
selection & programs PHY registers as per AN result.
Signed-off-by: Vikas Manocha <vikas.mano...@st.com>
Signed-off-by: Amit Virdi <amit.vi...@st.com>
---
drivers/net/designware.c | 43 +++++++++++++++++++++++++++++--------------
1 files changed, 29 insertions(+), 14 deletions(-)
diff --git a/drivers/net/designware.c b/drivers/net/designware.c
index ebb1fff..56f0c7a 100644
--- a/drivers/net/designware.c
+++ b/drivers/net/designware.c
@@ -399,8 +399,7 @@ static int configure_phy(struct eth_device *dev)
return -1;
#if defined(CONFIG_DW_AUTONEG)
- bmcr = BMCR_ANENABLE | BMCR_ANRESTART | BMCR_SPEED100 | \
- BMCR_FULLDPLX | BMCR_SPEED1000;
+ bmcr = BMCR_ANENABLE | BMCR_ANRESTART;
#else
bmcr = BMCR_SPEED100 | BMCR_FULLDPLX;
@@ -428,23 +427,39 @@ static int configure_phy(struct eth_device *dev)
eth_mdio_read(dev, phy_addr, MII_STAT1000, &btsr);
if (bmsr & BMSR_ANEGCOMPLETE) {
- if (btsr & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+ if (btsr & PHY_1000BTSR_1000FD) {
priv->speed = SPEED_1000M;
- if (btsr & PHY_1000BTSR_1000FD)
- priv->duplex = FULL_DUPLEX;
- else
- priv->duplex = HALF_DUPLEX;
+ bmcr |= BMCR_SPEED1000;
+ priv->duplex = FULL_DUPLEX;
+ bmcr |= BMCR_FULLDPLX;
+ } else if (btsr & PHY_1000BTSR_1000HD) {
+ priv->speed = SPEED_1000M;
+ bmcr |= BMCR_SPEED1000;
+ priv->duplex = HALF_DUPLEX;
+ bmcr &= ~BMCR_FULLDPLX;
+ } else if (anlpar & LPA_100FULL) {
+ priv->speed = SPEED_100M;
+ bmcr |= BMCR_SPEED100;
+ priv->duplex = FULL_DUPLEX;
+ bmcr |= BMCR_FULLDPLX;
+ } else if (anlpar & LPA_100HALF) {
+ priv->speed = SPEED_100M;
+ bmcr |= BMCR_SPEED100;
+ priv->duplex = HALF_DUPLEX;
+ bmcr &= ~BMCR_FULLDPLX;
+ } else if (anlpar & LPA_10FULL) {
+ priv->speed = SPEED_10M;
+ bmcr &= ~BMCR_SPEED100;
+ priv->duplex = FULL_DUPLEX;
+ bmcr |= BMCR_FULLDPLX;
} else {
- if (anlpar & LPA_100)
- priv->speed = SPEED_100M;
- else
priv->speed = SPEED_10M;
-
- if (anlpar & (LPA_10FULL | LPA_100FULL))
- priv->duplex = FULL_DUPLEX;
- else
+ bmcr &= ~BMCR_SPEED100;
priv->duplex = HALF_DUPLEX;
+ bmcr &= ~BMCR_FULLDPLX;
}
+ if (eth_mdio_write(dev, phy_addr, MII_BMCR, bmcr) < 0)
+ return -1;
} else
return -1;
#else
--
1.7.2.2
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
