The lcd_setcolreg() is a API provided by the lcd driver and used to setup the color lookup table. However the lcd driver setup the CLUT by using a lot of #ifdiffery and accessing the CLUT arrays which are cleanly hidden by the API call. Remove that and use the API.
Signed-off-by: Andreas Bießmann <andreas.de...@googlemail.com> Cc: Marek Vasut <ma...@denx.de> Cc: Bo Shen <voice.s...@atmel.com> Cc: Tom Rini <tr...@ti.com> --- This is a RFC currently cause it touches a lot of boards but is only runtime tested on at91sam9263ek. Unfortunately a 'MAKEALL -a arm' does break cause the atmel_hlcd driver do not provide the required API (lcd_setcolreg()) -> Bo, can you please fix this, I do not have an atmel_hlcdc enabled device. On the other hand this change also touches other architectures I can not test. This patch is actually only compile tested for arm and avr32 arches. And last I have to say that there is another position in this file where the CLUT is modified directly by the code. This should also be changed to use the lcd_setcolreg API. This patch shall superseed http://patchwork.ozlabs.org/patch/193466/ common/lcd.c | 47 +++++++++-------------------------------------- 1 file changed, 9 insertions(+), 38 deletions(-) diff --git a/common/lcd.c b/common/lcd.c index b6be800..4938381 100644 --- a/common/lcd.c +++ b/common/lcd.c @@ -523,11 +523,6 @@ static inline ushort *configuration_get_cmap(void) #ifdef CONFIG_LCD_LOGO void bitmap_plot(int x, int y) { -#ifdef CONFIG_ATMEL_LCD - uint *cmap = (uint *)bmp_logo_palette; -#else - ushort *cmap = (ushort *)bmp_logo_palette; -#endif ushort i, j; uchar *bmap; uchar *fb; @@ -545,44 +540,20 @@ void bitmap_plot(int x, int y) fb = (uchar *)(lcd_base + y * lcd_line_length + x); if (NBITS(panel_info.vl_bpix) < 12) { - /* Leave room for default color map - * default case: generic system with no cmap (most likely 16bpp) - * cmap was set to the source palette, so no change is done. - * This avoids even more ifdefs in the next stanza - */ -#if defined(CONFIG_MPC823) - cmap = (ushort *) &(cp->lcd_cmap[BMP_LOGO_OFFSET * sizeof(ushort)]); -#elif defined(CONFIG_ATMEL_LCD) - cmap = (uint *)configuration_get_cmap(); -#else - cmap = configuration_get_cmap(); -#endif WATCHDOG_RESET(); /* Set color map */ for (i = 0; i < ARRAY_SIZE(bmp_logo_palette); ++i) { - ushort colreg = bmp_logo_palette[i]; -#ifdef CONFIG_ATMEL_LCD - uint lut_entry; -#ifdef CONFIG_ATMEL_LCD_BGR555 - lut_entry = ((colreg & 0x000F) << 11) | - ((colreg & 0x00F0) << 2) | - ((colreg & 0x0F00) >> 7); -#else /* CONFIG_ATMEL_LCD_RGB565 */ - lut_entry = ((colreg & 0x000F) << 1) | - ((colreg & 0x00F0) << 3) | - ((colreg & 0x0F00) << 4); -#endif - *(cmap + BMP_LOGO_OFFSET) = lut_entry; - cmap++; -#else /* !CONFIG_ATMEL_LCD */ -#ifdef CONFIG_SYS_INVERT_COLORS - *cmap++ = 0xffff - colreg; -#else - *cmap++ = colreg; -#endif -#endif /* CONFIG_ATMEL_LCD */ + /* use the most significant bits here */ + uint8_t red = ((bmp_logo_palette[i] >> 4) & 0xF0); + uint8_t green = ((bmp_logo_palette[i] >> 0) & 0xF0); + uint8_t blue = ((bmp_logo_palette[i] << 4) & 0xF0); + debug("LCD: setup colreg %u with " + "R: 0x%02x G: 0x%02x B: 0x%02x (0x%04x)\n", + i+BMP_LOGO_OFFSET, red, green, blue, bmp_logo_palette[i]); + /* leave room for the default colormap here */ + lcd_setcolreg(i+BMP_LOGO_OFFSET, red, green, blue); } WATCHDOG_RESET(); -- 1.7.10.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
