Sorry about the delay. It's no dice on Hardy at this stage.
I tested the aforementioned modes: 1, 2, 4, and 8. All produced the same
result. My PW191 monitor indicates no signal. My keyboard number lock
and other lights are still working, but attempting to Ctrl+Alt+1 to a
console and reboot yields no discernible response.
The motherboard is Asus P5K PRO.
lspci -vvnn reports the following:
04:01.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon
9200 SE] [1002:5964] (rev 01) (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Unknown device [174b:7c25]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at fea00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fea20000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:01.1 Display controller [0380]: ATI Technologies Inc RV280 [Radeon 9200 SE]
(Secondary) [1002:5d44] (rev 01)
Subsystem: PC Partner Limited Unknown device [174b:7c24]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
The system is a home rebuild. The graphics card I am using was present
in the original machine configuration on an older Ubuntu, and worked in
that setting.
I haven't looked at the AGP Mode settings in the bios, but I remember
searching for settings when I first investigated this problem. My
recollection is that the settings were not available.
The card still works if I use the vesa driver. Does this rule out an
AGP-specific problem by any chance?
I'll give Intrepid a go.
--
[rv280] X fails to start under Hardy amd64
https://bugs.launchpad.net/bugs/240169
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
