Hi Oliver,
I did not know the first boot script would be important, since it made it all
the way through. What posted was the 2nd time around when it did not make it
all the way through (aka froze, although from what you say, maybe it didn't
freeze, just my display was not showing anything further...)
Below is the complete output from virgin image install on sd card until the
point of nothing happening (with the altered boot.scr as in my last post above):
Texas Instruments X-Loader 1.4.4ss (Sep 30 2010 - 14:44:32)
Beagle xM Rev A
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Beagle xM Rev A
Die ID #528e00001bf00000015739ea0702900b
Hit any key to stop autoboot: 3 2 1 0
mmc1 is available
Unknown command 'userbutton' - try 'help'
reading boot.scr
530 bytes read
Running bootscript from mmc ...
## Executing script at 80200000
Kernel is not ready for 1Ghz limiting to 800Mhz
mmc1 is available
reading uImage
3687812 bytes read
reading uInitrd
6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Ubuntu Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3687748 Bytes = 3.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: Ubuntu Initrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6769379 Bytes = 6.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35-22-omap (bui...@gourd) (gcc version 4.4.5
(Ubuntu/Linaro 4.4.4-14ubuntu4) ) #33-Ubuntu Mon Sep 20 03:17:30 UTC 2010
(Ubuntu 2.6.35-22.33-omap 2.6.35.4)
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[ 0.000000] Reserving 6291456 bytes SDRAM for VRAM
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 130048
[ 0.000000] Kernel command line: console=ttyS2,115200n8 console=tty0
root=/dev/mmcblk0p2 rootwait ro vram=${vram} omapfb.mode=tv:pal
omapdss.def_disp=tv fixrtc buddy=unknown
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 2621440 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cgroups
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 496164k/496164k available, 28124k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0044000 ( 240 kB)
[ 0.000000] .text : 0xc0044000 - 0xc06ac000 (6560 kB)
[ 0.000000] .data : 0xc0718000 - 0xc0767960 ( 319 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[ 0.000000] (null): no physical address for uart#3, so skipping
early_init...
[ 0.000000] omap_hwmod: l3_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_core_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_per_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP GPIO hardware version 2.5
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Calibrating delay loop... 507.32 BogoMIPS (lpj=1982464)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] AppArmor: AppArmor initialized
[ 0.000000] Yama: becoming mindful.
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys memory
[ 0.000000] Initializing cgroup subsys devices
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] OMAP3 Beagle Rev: xM
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at
/build/buildd/linux-2.6.35/arch/arm/mach-omap2/serial.c:727
omap_serial_init_port+0x88/0x1f8()
[ 0.000000] (null): can't init uart3, no clocks available
[ 0.000000] Modules linked in:
[ 0.000000] [<c004c508>] (unwind_backtrace+0x0/0x100) from [<c05142e8>]
(dump_stack+0x18/0x1c)
[ 0.000000] [<c05142e8>] (dump_stack+0x18/0x1c) from [<c0081bb8>]
(warn_slowpath_common+0x5c/0x6c)
[ 0.000000] [<c0081bb8>] (warn_slowpath_common+0x5c/0x6c) from [<c0081c6c>]
(warn_slowpath_fmt+0x38/0x40)
[ 0.000000] [<c0081c6c>] (warn_slowpath_fmt+0x38/0x40) from [<c0010814>]
(omap_serial_init_port+0x88/0x1f8)
[ 0.000000] [<c0010814>] (omap_serial_init_port+0x88/0x1f8) from
[<c00109b4>] (omap_serial_init+0x30/0x3c)
[ 0.000000] [<c00109b4>] (omap_serial_init+0x30/0x3c) from [<c00125e0>]
(omap3_beagle_init+0x6c/0xfc)
[ 0.000000] [<c00125e0>] (omap3_beagle_init+0x6c/0xfc) from [<c000c660>]
(customize_machine+0x24/0x2c)
[ 0.000000] [<c000c660>] (customize_machine+0x24/0x2c) from [<c00443bc>]
(do_one_initcall+0x3c/0x1dc)
[ 0.000000] [<c00443bc>] (do_one_initcall+0x3c/0x1dc) from [<c00085b4>]
(do_basic_setup+0x64/0x74)
[ 0.000000] [<c00085b4>] (do_basic_setup+0x64/0x74) from [<c0008654>]
(kernel_init+0x90/0x120)
[ 0.000000] [<c0008654>] (kernel_init+0x90/0x120) from [<c0045af4>]
(kernel_thread_exit+0x0/0x8)
[ 0.000000] ---[ end trace da227214a82491b7 ]---
[ 0.000000] Found NAND on CS0
[ 0.000000] Registering NAND on CS0
[ 0.000000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
counters available
[ 0.000091] OMAP DMA hardware revision 5.0
[ 0.004486] bio: create slab <bio-0> at 0
[ 0.006134] SCSI subsystem initialized
[ 0.006774] usbcore: registered new interface driver usbfs
[ 0.006866] usbcore: registered new interface driver hub
[ 0.007049] usbcore: registered new device driver usb
[ 0.018096] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
[ 0.020385] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.020416] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.020843] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.022888] regulator: VUSB1V5: 1500 mV normal standby
[ 0.023223] regulator: VUSB1V8: 1800 mV normal standby
[ 0.023559] regulator: VUSB3V1: 3100 mV normal standby
[ 0.024902] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.025543] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
[ 0.025909] regulator: VDAC: 1800 mV normal standby
[ 0.026367] regulator: VPLL2: 1800 mV normal standby
[ 0.026763] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
[ 0.037933] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
[ 0.038757] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.039276] NetLabel: Initializing
[ 0.039306] NetLabel: domain hash size = 128
[ 0.039306] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.039428] NetLabel: unlabeled traffic allowed by default
[ 0.039459] Switching to clocksource 32k_counter
[ 0.047332] AppArmor: AppArmor Filesystem Enabled
[ 0.056793] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[ 0.061798] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using
DMA, IRQ 92
[ 0.062042] NET: Registered protocol family 2
[ 0.062286] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.063171] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.063568] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.063781] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.063812] TCP reno registered
[ 0.063842] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.063873] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.064086] NET: Registered protocol family 1
[ 0.064941] PMU: registered new PMU device of type 0
[ 0.065032] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.065368] audit: initializing netlink socket (disabled)
[ 0.065460] type=2000 audit(0.257:1): initialized
[ 0.217376] Trying to unpack rootfs image as initramfs...
[ 6.805847] VFS: Disk quotas dquot_6.5.2
[ 6.806213] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 6.809204] fuse init (API version 7.14)
[ 6.809814] msgmni has been set to 969
[ 6.811401] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 6.811462] io scheduler noop registered
[ 6.811492] io scheduler deadline registered
[ 6.811584] io scheduler cfq registered (default)
[ 6.867919] OMAP DSS rev 2.0
[ 6.868072] OMAP DISPC rev 3.0
[ 6.868133] OMAP VENC rev 2
[ 6.949066] Freeing initrd memory: 6608K
[ 7.032897] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 7.116363] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[ 7.285400] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[ 7.454345] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[ 8.327209] console [ttyS2] enabled
[ 8.337738] brd: module loaded
[ 8.344268] loop: module loaded
[ 8.349060] omap2-nand driver initializing
[ 8.353515] NAND device: Manufacturer ID: 0x20, Chip ID: 0xba (ST Micro
omap2-nand.0)
[ 8.361450] NAND bus width 8 instead 16 bit
[ 8.365661] No NAND device found.
[ 8.369171] NAND device: Manufacturer ID: 0x20, Chip ID: 0xba (ST Micro NAND
256MiB 1,8V 16-bit)
[ 8.378082] Creating 5 MTD partitions on "omap2-nand.0":
[ 8.383483] 0x000000000000-0x000000080000 : "X-Loader"
[ 8.390075] 0x000000080000-0x000000260000 : "U-Boot"
[ 8.396850] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 8.403350] 0x000000280000-0x000000680000 : "Kernel"
[ 8.410827] 0x000000680000-0x000010000000 : "File System"
[ 8.506408] Fixed MDIO Bus: probed
[ 8.510223] PPP generic driver version 2.4.2
[ 8.514831] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256)
(6 bit encapsulation enabled).
[ 8.524627] CSLIP: code copyright 1989 Regents of the University of
California.
[ 8.532012] SLIP linefill/keepalive option.
[ 8.536437] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.543273] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 8.549072] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 8.556671] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 8.570892] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 8.577453] hub 1-0:1.0: USB hub found
[ 8.581329] hub 1-0:1.0: 3 ports detected
[ 8.610015] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.616760] mice: PS/2 mouse device common for all mice
[ 8.622589] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 8.628906] twl_rtc twl_rtc: Power up reset detected.
[ 8.634796] twl_rtc twl_rtc: Enabling TWL-RTC.
[ 8.640197] device-mapper: uevent: version 1.0.3
[ 8.645599] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised:
dm-de...@redhat.com
[ 8.654418] device-mapper: multipath: version 1.1.1 loaded
[ 8.660034] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 8.667266] cpuidle: using governor ladder
[ 8.671386] cpuidle: using governor menu
[ 8.675476] sdhci: Secure Digital Host Controller Interface driver
[ 8.681732] sdhci: Copyright(c) Pierre Ossman
[ 8.866333] No device for DAI omap-mcbsp-dai-0
[ 8.870880] No device for DAI omap-mcbsp-dai-1
[ 8.875366] No device for DAI omap-mcbsp-dai-2
[ 8.879882] No device for DAI omap-mcbsp-dai-3
[ 8.884368] No device for DAI omap-mcbsp-dai-4
[ 8.888854] Not OMAP3 EVM!
[ 8.891601] OMAP3 Beagle/Devkit8000 SoC init
[ 8.896697] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[ 8.905273] ALSA device list:
[ 8.908386] #0: omap3beagle (twl4030)
[ 8.912322] usb 1-2: new high speed USB device using ehci-omap and address 2
[ 8.920532] TCP cubic registered
[ 8.924926] NET: Registered protocol family 10
[ 8.930969] lo: Disabled Privacy Extensions
[ 8.936004] NET: Registered protocol family 17
[ 8.941833] Power Management for TI OMAP3.
[ 8.947906] VFP support v0.3: implementor 41 architecture 3 part 30 variant
c rev 3
[ 8.957366] registered taskstats version 1
[ 8.974426] omapfb omapfb: illegal display bpp
[ 8.978942] omapfb omapfb: failed to setup fb_info
[ 8.983825] omapfb omapfb: failed to setup omapfb
[ 8.988677] omapfb: probe of omapfb failed with error -22
[ 8.994659] regulator_init_complete: incomplete constraints, leaving VPLL2 on
[ 9.002105] regulator_init_complete: incomplete constraints, leaving VDAC on
[ 9.010284] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC
(946684800)
[ 9.018737] Freeing init memory: 240K
[ 9.080261] hub 1-2:1.0: USB hub found
[ 9.093750] hub 1-2:1.0: 5 ports detected
[ 9.160614] udev[67]: starting version 163
[ 9.188262] mmc0: host does not support reading read-only switch. assuming
write-enable.
[ 9.229309] mmc0: new high speed SDHC card at address aaaa
[ 9.392822] usb 1-2.1: new high speed USB device using ehci-omap and address
3
[ 9.460601] mmcblk0: mmc0:aaaa SU04G 3.69 GiB
[ 9.500244] mmcblk0: p1 p2
[ 10.681823] Btrfs loaded
[ 11.828643] mmcblk0: p1 p2
[ 17.727233] EXT3-fs: barriers not enabled
[ 17.732208] kjournald starting. Commit interval 5 seconds
[ 17.740600] EXT3-fs (mmcblk0p2): using internal journal
[ 17.745941] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 73.439270] EXT3-fs: barriers not enabled
[ 73.444396] kjournald starting. Commit interval 5 seconds
[ 73.450103] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 74.077728] EXT3-fs (mmcblk0p2): using internal journal
[ 252.725830] md: stopping all md devices.
[ 253.583465] Restarting system.
Texas Instruments X-Loader 1.4.4ss (Sep 30 2010 - 14:44:32)
Beagle xM Rev A
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Beagle xM Rev A
Die ID #528e00001bf00000015739ea0702900b
Hit any key to stop autoboot: 3 2 1 0
mmc1 is available
Unknown command 'userbutton' - try 'help'
reading boot.scr
352 bytes read
Running bootscript from mmc ...
## Executing script at 80200000
reading uImage
3687812 bytes read
reading uInitrd
6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Ubuntu Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3687748 Bytes = 3.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: Ubuntu Initrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6769379 Bytes = 6.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
fsck from util-linux-ng 2.17.2
/dev/mmcblk0p2: clean, 118171/446832 files, 533063/949843 blocks
* Starting AppArmor profiles Skipping profile in
/etc/apparmor.d/disable: usr.bin.firefox
[ OK ]
* Setting sensors limits [ OK ]
speech-dispatcher disabled; edit /etc/default/speech-dispatcher
fsck from util-linux-ng 2.17.2
/dev/mmcblk0p2: clean, 118171/446832 files, 533063/949843 blocks
* Starting AppArmor profiles Skipping profile in
/etc/apparmor.d/disable: usr.bin.firefox
[ OK ]
* Setting sensors limits [ OK ]
* PulseAudio configured for per-user sessions
saned disabled; edit /etc/default/saned
* Enabling additional executable binary formats binfmt-support [ OK ]
--
BeagleBoard xM freezes while attempting to boot 10.10
https://bugs.launchpad.net/bugs/664827
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
