download linux-2.6.35-rc3 from kernel.org...ok...compilation kernel...use kernel-package and config-2.6.35.-23-generic...ok...succes...starting in use 6 Gb/s (Sata 3) WD 1TBFAEX and external controler marvell 9128 (controler only one manipulate...only IDE)...and...
dmesg (...) : ... [ 1.389553] pata_acpi 0000:08:00.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19 [ 1.389574] pata_acpi 0000:08:00.0: setting latency timer to 64 [ 1.389584] pata_acpi 0000:08:00.0: PCI INT A disabled ... [ 1.951122] ahci 0000:00:09.0: version 3.0 [ 1.951278] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 22 [ 1.951281] ahci 0000:00:09.0: PCI INT A -> Link[LSA0] -> GSI 22 (level, low) -> IRQ 22 [ 1.951314] ahci 0000:00:09.0: irq 48 for MSI/MSI-X [ 1.951319] ahci 0000:00:09.0: controller can't do PMP, turning off CAP_PMP [ 1.951358] ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 1.951361] ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pio sxs boh [ 1.951363] ahci 0000:00:09.0: setting latency timer to 64 [ 1.951933] scsi0 : ahci [ 1.952009] scsi1 : ahci [ 1.952049] scsi2 : ahci [ 1.952090] scsi3 : ahci [ 1.952131] scsi4 : ahci [ 1.952172] scsi5 : ahci [ 1.952252] ata1: SATA max UDMA/133 abar m8...@0xf9e76000 port 0xf9e76100 irq 48 [ 1.952254] ata2: SATA max UDMA/133 abar m8...@0xf9e76000 port 0xf9e76180 irq 48 [ 1.952256] ata3: SATA max UDMA/133 abar m8...@0xf9e76000 port 0xf9e76200 irq 48 [ 1.952258] ata4: SATA max UDMA/133 abar m8...@0xf9e76000 port 0xf9e76280 irq 48 [ 1.952259] ata5: SATA max UDMA/133 abar m8...@0xf9e76000 port 0xf9e76300 irq 48 [ 1.952261] ata6: SATA max UDMA/133 abar m8...@0xf9e76000 port 0xf9e76380 irq 48 [ 1.952342] ahci 0000:08:00.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19 [ 1.952380] ahci 0000:08:00.0: irq 49 for MSI/MSI-X [ 1.952393] ahci 0000:08:00.0: controller can do FBS, turning on CAP_FBS [ 1.970086] ahci 0000:08:00.0: AHCI 0001.0200 32 slots 8 ports 6 Gbps 0xff impl IDE mode [ 1.970088] ahci 0000:08:00.0: flags: 64bit ncq fbs pio [ 1.970094] ahci 0000:08:00.0: setting latency timer to 64 [ 1.970885] scsi6 : ahci [ 1.970933] scsi7 : ahci [ 1.970978] scsi8 : ahci [ 1.971022] scsi9 : ahci [ 1.971066] scsi10 : ahci [ 1.971109] scsi11 : ahci [ 1.971155] scsi12 : ahci [ 1.971199] scsi13 : ahci [ 1.971231] ata7: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeff900 irq 49 [ 1.971234] ata8: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeff980 irq 49 [ 1.971236] ata9: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeffa00 irq 49 [ 1.971239] ata10: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeffa80 irq 49 [ 1.971241] ata11: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeffb00 irq 49 [ 1.971244] ata12: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeffb80 irq 49 [ 1.971246] ata13: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeffc00 irq 49 [ 1.971249] ata14: SATA max UDMA/133 abar m2...@0xfdeff800 port 0xfdeffc80 irq 49 [ 2.110030] usb 4-1: new low speed USB device using ohci_hcd and address 2 [ 2.300036] ata6: SATA link down (SStatus 0 SControl 300) [ 2.300050] ata4: SATA link down (SStatus 0 SControl 300) [ 2.300063] ata1: SATA link down (SStatus 0 SControl 300) [ 2.300074] ata5: SATA link down (SStatus 0 SControl 300) [ 2.310024] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.310038] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.310184] ata3.00: ATAPI: ASUS DRW-2014L1T, 1.02, max UDMA/66 [ 2.310453] ata3.00: configured for UDMA/66 [ 2.338920] ata2.00: ATA-8: ST3500320NS, SN06, max UDMA/133 [ 2.338922] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.340046] ata10: SATA link down (SStatus 0 SControl 300) [ 2.340073] ata12: SATA link down (SStatus 0 SControl 300) [ 2.340102] ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.340125] ata11: SATA link down (SStatus 0 SControl 300) [ 2.340148] ata8: SATA link down (SStatus 0 SControl 300) [ 2.340171] ata13: SATA link down (SStatus 0 SControl 300) [ 2.340198] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 2.340219] ata9: SATA link down (SStatus 0 SControl 300) [ 2.340232] ata14.00: ATAPI: MARVELL VIRTUALL, 1.09, max UDMA/66 [ 2.340368] ata14.00: configured for UDMA/66 [ 2.348630] ata7.00: ATA-8: WDC WD1002FAEX-00Z3A0, 05.01D05, max UDMA/133 [ 2.348632] ata7.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA [ 2.350738] ata7.00: configured for UDMA/133 [ 2.381179] ata2.00: configured for UDMA/133 [ 2.381289] scsi 1:0:0:0: Direct-Access ATA ST3500320NS SN06 PQ: 0 ANSI: 5 [ 2.381394] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 2.381407] sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 2.381484] sd 1:0:0:0: [sda] Write Protect is off [ 2.381487] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.381510] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.381783] scsi 2:0:0:0: CD-ROM ASUS DRW-2014L1T 1.02 PQ: 0 ANSI: 5 [ 2.384495] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.384497] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.384570] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 2.384610] sr 2:0:0:0: Attached scsi generic sg1 type 5 [ 2.384762] scsi 6:0:0:0: Direct-Access ATA WDC WD1002FAEX-0 05.0 PQ: 0 ANSI: 5 [ 2.384857] sd 6:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2.384880] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 2.384916] sd 6:0:0:0: [sdb] Write Protect is off [ 2.384918] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.384933] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.385059] scsi 13:0:0:0: Processor Marvell 91xx Config 1.01 PQ: 0 ANSI: 5 [ 2.385152] scsi 13:0:0:0: Attached scsi generic sg3 type 3 [ 2.389677] sda: [ 2.389844] sd 1:0:0:0: [sda] Attached SCSI disk [ 2.402636] usbcore: registered new interface driver usbhid [ 2.402637] usbhid: USB HID core driver [ 2.403150] sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 > [ 2.403439] sd 6:0:0:0: [sdb] Attached SCSI disk ... ...marvell is run IDE mode ?...ahci mode ?...sata mode ?...hmmm...sata mode or ide mode ?...8 ports ??? ( only 2 ports for this external controler...)...very sorry...this patch is...very...very...you think ?... this is bad ?... mervell 9128 and WD 1TBFAEX <=> HDD: read max. ~120 MB/s ???... whrite max. ~90 MB/s ???.... how to use is full speed for 6Gb/s ( windows 7: HDD: read min. ~160...180 MB/s ...last HDTach - burst speed ~927 MB/s ! ) ???...how to AHCI mode for external controler ???... -- In Live session or installation HD not recognized https://bugs.launchpad.net/bugs/658521 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
