** Description changed: - Hi, - I just did a fresh install of Ubuntu 14.04 LTS onto a machine here. During the installation (which is pre-seeded) and in the BIOS, my - keyboard works flawlessly. - - However, the moment I boot the machine up, I note the keyboard is not - operational. Naturally, I discover this *after* buggering up my - networking settings. + keyboard works flawlessly. However, the moment I boot the machine up, I + note the keyboard is not operational. Naturally, I discover this + *after* buggering up my networking settings. The offending package is linux-image-3.13.0-24-generic version 3.13.0-24.46. At one point I noticed an "irq 16: nobody cared" error message. Due to there being no network connectivity, I was unable to capture the message displayed. The output from `dmesg` (see attachment dmesg.txt) suggests it does see USB and the keyboard, but plugging the keyboard into any of the available ports and pressing keys has no effect on the console. The machine is a rack-mounted server, intended to run headless. The motherboard is an Intel DQ77MK. No peripheral cards are installed. - root@host:~# cat /proc/version_signature - Ubuntu 3.13.0-24.46-generic 3.13.9 - root@host:~# lspci -vnvn - 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller [8086:0150] (rev 09) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- - Latency: 0 - Capabilities: [e0] Vendor Specific Information: Len=0c <?> - - 00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller [8086:0152] (rev 09) (prog-if 00 [VGA controller]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin A routed to IRQ 11 - Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M] - Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] - Region 4: I/O ports at f000 [size=64] - Expansion ROM at <unassigned> [disabled] - Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- - Address: 00000000 Data: 0000 - Capabilities: [d0] Power Management version 2 - Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [a4] PCI Advanced Features - AFCap: TP+ FLR+ - AFCtrl: FLR- - AFStatus: TP- - - 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin A routed to IRQ 40 - Region 0: Memory at f7e20000 (64-bit, non-prefetchable) [size=64K] - Capabilities: [70] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+ - Address: 00000000fee0a00c Data: 4181 - Kernel driver in use: xhci_hcd - - 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin A routed to IRQ 11 - Region 0: Memory at f7e3c000 (64-bit, non-prefetchable) [size=16] - Capabilities: [50] Power Management version 3 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+ - Address: 0000000000000000 Data: 0000 - - 00:16.3 Serial controller [0700]: Intel Corporation 7 Series/C210 Series Chipset Family KT Controller [8086:1e3d] (rev 04) (prog-if 02 [16550]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin B routed to IRQ 19 - Region 0: I/O ports at f0e0 [size=8] - Region 1: Memory at f7e3a000 (32-bit, non-prefetchable) [size=4K] - Capabilities: [c8] Power Management version 3 - Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ - Address: 0000000000000000 Data: 0000 - Kernel driver in use: serial - - 00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 04) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin A routed to IRQ 41 - Region 0: Memory at f7e00000 (32-bit, non-prefetchable) [size=128K] - Region 1: Memory at f7e39000 (32-bit, non-prefetchable) [size=4K] - Region 2: I/O ports at f080 [size=32] - Capabilities: [c8] Power Management version 2 - Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- - Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ - Address: 00000000fee0400c Data: 4142 - Capabilities: [e0] PCI Advanced Features - AFCap: TP+ FLR+ - AFCtrl: FLR- - AFStatus: TP+ - Kernel driver in use: e1000e - - 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin A routed to IRQ 16 - Region 0: Memory at f7e38000 (32-bit, non-prefetchable) [size=1K] - Capabilities: [50] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [58] Debug port: BAR=1 offset=00a0 - Capabilities: [98] PCI Advanced Features - AFCap: TP+ FLR+ - AFCtrl: FLR- - AFStatus: TP- - Kernel driver in use: ehci-pci - - 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0, Cache Line Size: 64 bytes - Interrupt: pin A routed to IRQ 3 - Region 0: Memory at f7e30000 (64-bit, non-prefetchable) [size=16K] - Capabilities: [50] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+ - Address: 0000000000000000 Data: 0000 - Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 - DevCap: MaxPayload 128 bytes, PhantFunc 0 - ExtTag- RBE- - DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- - RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ - MaxPayload 128 bytes, MaxReadReq 128 bytes - DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- - Capabilities: [100 v1] Virtual Channel - Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 - Arb: Fixed- WRR32- WRR64- WRR128- - Ctrl: ArbSelect=Fixed - Status: InProgress- - VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- - Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- - Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 - Status: NegoPending- InProgress- - VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- - Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- - Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22 - Status: NegoPending- InProgress- - Capabilities: [130 v1] Root Complex Link - Desc: PortNumber=0f ComponentID=00 EltType=Config - Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ - Addr: 00000000fed1c000 - - 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode]) - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0, Cache Line Size: 64 bytes - Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 - Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- - BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- - PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- - Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 - DevCap: MaxPayload 128 bytes, PhantFunc 0 - ExtTag- RBE+ - DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- - RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- - MaxPayload 128 bytes, MaxReadReq 128 bytes - DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- - LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us - ClockPM- Surprise- LLActRep+ BwNot- - LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk- - ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- - LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- - SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- - Slot #0, PowerLimit 25.000W; Interlock- NoCompl+ - SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- - Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- - SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- - Changed: MRL- PresDet- LinkState- - RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- - RootCap: CRSVisible- - RootSta: PME ReqID 0000, PMEStatus- PMEPending- - DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd- - DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- - LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- - Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- - Compliance De-emphasis: -6dB - LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- - EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- - Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- - Address: 00000000 Data: 0000 - Capabilities: [90] Subsystem: Intel Corporation Device [8086:2035] - Capabilities: [a0] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- - Kernel driver in use: pcieport - - 00:1c.6 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 7 [8086:1e1c] (rev c4) (prog-if 00 [Normal decode]) - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0, Cache Line Size: 64 bytes - Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 - I/O behind bridge: 0000e000-0000efff - Memory behind bridge: f7d00000-f7dfffff - Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- - BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- - PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- - Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 - DevCap: MaxPayload 128 bytes, PhantFunc 0 - ExtTag- RBE+ - DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- - RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- - MaxPayload 128 bytes, MaxReadReq 128 bytes - DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- - LnkCap: Port #7, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us - ClockPM- Surprise- LLActRep+ BwNot- - LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ - ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- - SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- - Slot #6, PowerLimit 10.000W; Interlock- NoCompl+ - SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- - Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- - SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- - Changed: MRL- PresDet- LinkState- - RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- - RootCap: CRSVisible- - RootSta: PME ReqID 0000, PMEStatus- PMEPending- - DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd- - DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- - LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- - Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- - Compliance De-emphasis: -6dB - LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- - EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- - Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- - Address: 00000000 Data: 0000 - Capabilities: [90] Subsystem: Intel Corporation Device [8086:2035] - Capabilities: [a0] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- - Kernel driver in use: pcieport - - 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin A routed to IRQ 23 - Region 0: Memory at f7e37000 (32-bit, non-prefetchable) [size=1K] - Capabilities: [50] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ - Capabilities: [58] Debug port: BAR=1 offset=00a0 - Capabilities: [98] PCI Advanced Features - AFCap: TP+ FLR+ - AFCtrl: FLR- - AFStatus: TP- - Kernel driver in use: ehci-pci - - 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a4) (prog-if 01 [Subtractive decode]) - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 - Memory behind bridge: f7c00000-f7cfffff - Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- - BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- - PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- - Capabilities: [50] Subsystem: Intel Corporation Device [8086:2035] - - 00:1f.0 ISA bridge [0601]: Intel Corporation Q77 Express Chipset LPC Controller [8086:1e47] (rev 04) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Capabilities: [e0] Vendor Specific Information: Len=0c <?> - - 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e02] (rev 04) (prog-if 01 [AHCI 1.0]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ - Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0 - Interrupt: pin B routed to IRQ 42 - Region 0: I/O ports at f0d0 [size=8] - Region 1: I/O ports at f0c0 [size=4] - Region 2: I/O ports at f0b0 [size=8] - Region 3: I/O ports at f0a0 [size=4] - Region 4: I/O ports at f060 [size=32] - Region 5: Memory at f7e36000 (32-bit, non-prefetchable) [size=2K] - Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- - Address: fee0a00c Data: 41b1 - Capabilities: [70] Power Management version 3 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) - Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 - Capabilities: [b0] PCI Advanced Features - AFCap: TP+ FLR+ - AFCtrl: FLR- - AFStatus: TP- - Kernel driver in use: ahci - - 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Interrupt: pin C routed to IRQ 11 - Region 0: Memory at f7e35000 (64-bit, non-prefetchable) [size=256] - Region 4: I/O ports at f040 [size=32] - - 02:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 0, Cache Line Size: 64 bytes - Interrupt: pin A routed to IRQ 18 - Region 0: Memory at f7d00000 (32-bit, non-prefetchable) [size=128K] - Region 2: I/O ports at e000 [size=32] - Region 3: Memory at f7d20000 (32-bit, non-prefetchable) [size=16K] - Capabilities: [c8] Power Management version 2 - Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- - Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ - Address: 0000000000000000 Data: 0000 - Capabilities: [e0] Express (v1) Endpoint, MSI 00 - DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us - ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- - DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ - RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ - MaxPayload 128 bytes, MaxReadReq 512 bytes - DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- - LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <128ns, L1 <64us - ClockPM- Surprise- LLActRep- BwNot- - LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ - ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- - Capabilities: [a0] MSI-X: Enable+ Count=5 Masked- - Vector table: BAR=3 offset=00000000 - PBA: BAR=3 offset=00002000 - Capabilities: [100 v1] Advanced Error Reporting - UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- - UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- - UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- - CESta: RxErr- BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr- - CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ - AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- - Capabilities: [140 v1] Device Serial Number 70-54-d2-ff-ff-ab-9f-0f - Kernel driver in use: e1000e - - 03:03.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW322/323 [TrueFire] 1394a Controller [11c1:5811] (rev 70) (prog-if 10 [OHCI]) - Subsystem: Intel Corporation Device [8086:2035] - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- - Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 64 bytes - Interrupt: pin A routed to IRQ 10 - Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=4K] - Capabilities: [44] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- - I've had to do a rebuild already because of this bug (no console access then loosing network access pretty much means game over), so I can confirm 100% repeatability thus far. For interests' sake, the netboot image I used to perform this installation was downloaded this morning, and has the following checksums: 01f16ef8b1f11b29bd0ce940b0aad8ea950f5346 trusty/amd64/linux fbb74f8e7d0c1e2ce4b027fc4a0e1aca54cf0fe5 trusty/amd64/initrd.gz - If there's any additional information that would be useful, please let me know. - Regards, - Stuart Longland - --- + --- AlsaDevices: - total 0 - crw-rw---- 1 root audio 116, 1 Apr 28 14:35 seq - crw-rw---- 1 root audio 116, 33 Apr 28 14:35 timer + total 0 + crw-rw---- 1 root audio 116, 1 Apr 28 14:35 seq + crw-rw---- 1 root audio 116, 33 Apr 28 14:35 timer AplayDevices: Error: [Errno 2] No such file or directory ApportVersion: 2.14.1-0ubuntu3 Architecture: amd64 ArecordDevices: Error: [Errno 2] No such file or directory AudioDevicesInUse: Error: command ['fuser', '-v', '/dev/snd/seq', '/dev/snd/timer'] failed with exit code 1: CRDA: Error: [Errno 2] No such file or directory DistroRelease: Ubuntu 14.04 HibernationDevice: RESUME=UUID=c087705d-cbe4-4546-bfcd-436edfe047c8 IwConfig: Error: [Errno 2] No such file or directory Package: linux (not installed) ProcFB: 0 VESA VGA ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-3.13.0-24-generic root=UUID=8c972a72-4f98-4043-b9a1-d409f02d6dbc ro quiet splash vt.handoff=7 ProcVersionSignature: Ubuntu 3.13.0-24.46-generic 3.13.9 RelatedPackageVersions: - linux-restricted-modules-3.13.0-24-generic N/A - linux-backports-modules-3.13.0-24-generic N/A - linux-firmware N/A + linux-restricted-modules-3.13.0-24-generic N/A + linux-backports-modules-3.13.0-24-generic N/A + linux-firmware N/A RfKill: Error: [Errno 2] No such file or directory Tags: trusty Uname: Linux 3.13.0-24-generic x86_64 UpgradeStatus: No upgrade log present (probably fresh install) UserGroups: - + _MarkForUpload: True dmi.bios.date: 11/20/2012 dmi.bios.vendor: Intel Corp. dmi.bios.version: MKQ7710H.86A.0054.2012.1120.1444 dmi.board.asset.tag: To be filled by O.E.M. dmi.board.name: DQ77MK dmi.board.vendor: Intel Corporation dmi.board.version: AAG39642-500 dmi.chassis.type: 3 dmi.modalias: dmi:bvnIntelCorp.:bvrMKQ7710H.86A.0054.2012.1120.1444:bd11/20/2012:svn:pn:pvr:rvnIntelCorporation:rnDQ77MK:rvrAAG39642-500:cvn:ct3:cvr:
** Tags added: bios-outdated-0065 -- You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. https://bugs.launchpad.net/bugs/1313497 Title: USB keyboard unresponsive on fresh install To manage notifications about this bug go to: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1313497/+subscriptions -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
