It was working fine for me a couple of months ago. Not it crashes with a
segmentation fault.

---------------------------------------------------------------------------------
george@george-Ryzen:~$ gsmartcontrol
<warn>  [hz] Warning: exit: Device open failed, or device did not return an 
IDENTIFY DEVICE structure.
<warn>  [app] SmartctlParser::parse_full(): No ATA sections could be parsed. 
Returning.
<warn>  [hz] Warning: exit: Device open failed, or device did not return an 
IDENTIFY DEVICE structure.
<warn>  [app] SmartctlParser::parse_full(): No ATA sections could be parsed. 
Returning.
<warn>  [hz] Warning: exit: Device open failed, or device did not return an 
IDENTIFY DEVICE structure.
<warn>  [app] SmartctlParser::parse_full(): No ATA sections could be parsed. 
Returning.
<warn>  [hz] Warning: exit: Device open failed, or device did not return an 
IDENTIFY DEVICE structure.
<warn>  [app] SmartctlParser::parse_full(): No ATA sections could be parsed. 
Returning.
<warn>  [hz] Warning: exit: Device open failed, or device did not return an 
IDENTIFY DEVICE structure.
Segmentation fault (core dumped)

----------------------------------------------------------------------------

Also using sudo:

george@george-Ryzen:~$ sudo gsmartcontrol
<warn>  [hz] Warning: exit: Device open failed, or device did not return an 
IDENTIFY DEVICE structure.
Segmentation fault

----------------------------------------------------------------------------

smartctl is working OK:

george@george-Ryzen:~$ sudo smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.3.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     Samsung SSD 860 EVO 500GB
Serial Number:    S3Z2NB0K172360E
LU WWN Device Id: 5 002538 e400c377f
Firmware Version: RVT01B6Q
User Capacity:    500.107.862.016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   Unknown(0x09fc), ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Feb  7 23:06:50 2020 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x53) SMART execute Offline immediate.
                                        Auto Offline data collection on/off 
support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  85) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  
WHEN_FAILED RAW_VALUE
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       
-       0
  9 Power_On_Hours          0x0032   099   099   000    Old_age   Always       
-       2939
 12 Power_Cycle_Count       0x0032   098   098   000    Old_age   Always       
-       1194
177 Wear_Leveling_Count     0x0013   099   099   000    Pre-fail  Always       
-       6
179 Used_Rsvd_Blk_Cnt_Tot   0x0013   100   100   010    Pre-fail  Always       
-       0
181 Program_Fail_Cnt_Total  0x0032   100   100   010    Old_age   Always       
-       0
182 Erase_Fail_Count_Total  0x0032   100   100   010    Old_age   Always       
-       0
183 Runtime_Bad_Block       0x0013   100   100   010    Pre-fail  Always       
-       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       
-       0
190 Airflow_Temperature_Cel 0x0032   077   051   000    Old_age   Always       
-       23
195 Hardware_ECC_Recovered  0x001a   200   200   000    Old_age   Always       
-       0
199 UDMA_CRC_Error_Count    0x003e   100   100   000    Old_age   Always       
-       0
235 Unknown_Attribute       0x0012   099   099   000    Old_age   Always       
-       5
241 Total_LBAs_Written      0x0032   099   099   000    Old_age   Always       
-       6046203738

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

-- 
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/1789454

Title:
  gsmartcontrol immediately crashes while running smartctl

To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/gsmartcontrol/+bug/1789454/+subscriptions

-- 
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs

Reply via email to