Not sure where to go from this error...
[INFO]
------------------------------------------------------------------------
[INFO] BUILD FAILURE
[INFO]
------------------------------------------------------------------------
[INFO] Total time: 19:18 min
[INFO] Finished at: 2017-05-06T08:51:59+10:00
[INFO] Final Memory: 202M/3734M
[INFO]
------------------------------------------------------------------------
[ERROR] Failed to execute goal
com.github.eirslett:frontend-maven-plugin:1.3:npm (ng build) on project
metron-config: Failed to run task: 'npm run build' failed. (error code 1)
-> [Help 1]
[ERROR]
[ERROR] To see the full stack trace of the errors, re-run Maven with the -e
switch.
[ERROR] Re-run Maven using the -X switch to enable full debug logging.
[ERROR]
[ERROR] For more information about the errors and possible solutions,
please read the following articles:
[ERROR] [Help 1]
http://cwiki.apache.org/confluence/display/MAVEN/MojoFailureException
[ERROR]
[ERROR] After correcting the problems, you can resume the build with the
command
[ERROR] mvn <goals> -rf :metron-config
Changing to full dev platform directory
Vagrant Global Status
id name provider state directory
--------------------------------------------------------------------
There are no active Vagrant environments on this computer! Or,
you haven't destroyed and recreated Vagrant environments that were
started with an older version of Vagrant.
Running with ansible-skip-tags: ["sensors", "quick_dev"]
Bringing up enviroment
Running with ansible-skip-tags: ["sensors", "quick_dev"]
Bringing machine 'node1' up with 'virtualbox' provider...
==> node1: Importing base box 'metron/centos_base'...
==> node1: Matching MAC address for NAT networking...
==> node1: Checking if box 'metron/centos_base' is up to date...
==> node1: Setting the name of the VM:
full-dev-platform_node1_1494024744485_79418
==> node1: Fixed port collision for 22 => 2222. Now on port 2200.
==> node1: Clearing any previously set network interfaces...
==> node1: Preparing network interfaces based on configuration...
node1: Adapter 1: nat
node1: Adapter 2: hostonly
==> node1: Forwarding ports...
node1: 22 (guest) => 2200 (host) (adapter 1)
==> node1: Running 'pre-boot' VM customizations...
==> node1: Booting VM...
==> node1: Waiting for machine to boot. This may take a few minutes...
node1: SSH address: 127.0.0.1:2200
node1: SSH username: vagrant
node1: SSH auth method: private key
node1: Warning: Connection reset. Retrying...
node1: Warning: Remote connection disconnect. Retrying...
node1: Warning: Connection reset. Retrying...
node1: Warning: Remote connection disconnect. Retrying...
node1: Warning: Connection reset. Retrying...
node1: Warning: Remote connection disconnect. Retrying...
node1:
node1: Vagrant insecure key detected. Vagrant will automatically replace
node1: this with a newly generated keypair for better security.
node1:
node1: Inserting generated public key within guest...
node1: Removing insecure key from the guest if it's present...
node1: Key inserted! Disconnecting and reconnecting using new SSH key...
==> node1: Machine booted and ready!
==> node1: Checking for guest additions in VM...
==> node1: Setting hostname...
The following SSH command responded with a non-zero exit status.
Vagrant assumes that this means the command failed!
# Update sysconfig
sed -i 's/\(HOSTNAME=\).*/\1node1/' /etc/sysconfig/network
# Update DNS
sed -i 's/\(DHCP_HOSTNAME=\).*/\1"node1"/'
/etc/sysconfig/network-scripts/ifcfg-*
# Set the hostname - use hostnamectl if available
echo 'node1' > /etc/hostname
if command -v hostnamectl; then
hostnamectl set-hostname --static 'node1'
hostnamectl set-hostname --transient 'node1'
else
hostname -F /etc/hostname
fi
# Remove comments and blank lines from /etc/hosts
sed -i'' -e 's/#.*$//' -e '/^$/d' /etc/hosts
# Prepend ourselves to /etc/hosts
grep -w 'node1' /etc/hosts || {
sed -i'' '1i 127.0.0.1\tnode1\tnode1' /etc/hosts
}
# Restart network
service network restart
Stdout from the command:
Shutting down interface eth0: [ OK ]
Shutting down interface eth1: [ OK ]
Shutting down loopback interface: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... done.
[ OK ]
Bringing up interface eth1: Determining if ip address 192.168.66.121 is
already in use for device eth1...
Error, some other host (08:00:27:03:75:75) already uses address
192.168.66.121.
[FAILED]
Stderr from the command:
