Can you give me the link?? On 18 Dec 2017 5:14 p.m., "zeo...@gmail.com" <zeo...@gmail.com> wrote:
> You can send them via email or if they're too long upload to a > pastebin website and send a link. > > Jon > > On Mon, Dec 18, 2017 at 6:14 AM Gaurav Bapat <gauravb3...@gmail.com> > wrote: > >> The metron component was up for 3 hours but later lost the heartbeats of >> all component. >> >> From were do I send you the logs?? >> >> >> >> On 18 December 2017 at 15:58, zeo...@gmail.com <zeo...@gmail.com> wrote: >> >>> Can you provide the logs of the initial failure? >>> >>> Jon >>> >>> On Sun, Dec 17, 2017, 23:55 Gaurav Bapat <gauravb3...@gmail.com> wrote: >>> >>>> [gaurav@metron full-dev-platform]$ cat Vagrantfile >>>> # >>>> # Licensed to the Apache Software Foundation (ASF) under one or more >>>> # contributor license agreements. See the NOTICE file distributed with >>>> # this work for additional information regarding copyright ownership. >>>> # The ASF licenses this file to You under the Apache License, Version >>>> 2.0 >>>> # (the "License"); you may not use this file except in compliance with >>>> # the License. You may obtain a copy of the License at >>>> # >>>> # http://www.apache.org/licenses/LICENSE-2.0 >>>> # >>>> # Unless required by applicable law or agreed to in writing, software >>>> # distributed under the License is distributed on an "AS IS" BASIS, >>>> # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or >>>> implied. >>>> # See the License for the specific language governing permissions and >>>> # limitations under the License. >>>> # >>>> require 'getoptlong' >>>> >>>> ansibleTags='' >>>> ansibleSkipTags='sensors' >>>> >>>> begin >>>> opts = GetoptLong.new( >>>> [ '--ansible-tags', GetoptLong::OPTIONAL_ARGUMENT ], >>>> [ '--ansible-skip-tags', GetoptLong::OPTIONAL_ARGUMENT ] >>>> ) >>>> >>>> opts.quiet = TRUE >>>> >>>> opts.each do |opt, arg| >>>> case opt >>>> when '--ansible-tags' >>>> ansibleTags=arg >>>> when '--ansible-skip-tags' >>>> ansibleSkipTags=arg >>>> end >>>> end >>>> rescue Exception => ignored >>>> #Ignore to allow other opts to be passed to Vagrant >>>> end >>>> >>>> puts " Running with ansible-tags: " + ansibleTags.split(",").to_s if >>>> ansibleTags != '' >>>> puts " Running with ansible-skip-tags: " + >>>> ansibleSkipTags.split(",").to_s if ansibleSkipTags != '' >>>> >>>> hosts = [{ >>>> hostname: "node1", >>>> ip: "192.168.66.121", >>>> memory: "8192", >>>> cpus: 4, >>>> promisc: 2 # enables promisc on the 'Nth' network interface >>>> }] >>>> >>>> Vagrant.configure(2) do |config| >>>> >>>> # all hosts built on centos 6 >>>> config.vm.box = "metron/centos_base" >>>> config.ssh.insert_key = true >>>> >>>> # enable the hostmanager plugin >>>> config.hostmanager.enabled = true >>>> config.hostmanager.manage_host = true >>>> >>>> # host definition >>>> hosts.each_with_index do |host, index| >>>> config.vm.define host[:hostname] do |node| >>>> >>>> # host settings >>>> node.vm.hostname = host[:hostname] >>>> node.vm.network "private_network", ip: host[:ip] >>>> >>>> # vm settings >>>> node.vm.provider "virtualbox" do |vb| >>>> vb.memory = host[:memory] >>>> vb.cpus = host[:cpus] >>>> >>>> # enable promisc mode on the network interface >>>> if host.has_key?(:promisc) >>>> vb.customize ["modifyvm", :id, "--nicpromisc#{host[:promisc]}", >>>> "allow-all"] >>>> end >>>> end >>>> end >>>> end >>>> >>>> # provisioning >>>> config.vm.provision :ansible do |ansible| >>>> ansible.playbook = "../../playbooks/metron_full_install.yml" >>>> ansible.sudo = true >>>> ansible.tags = ansibleTags.split(",") if ansibleTags != '' >>>> ansible.skip_tags = ansibleSkipTags.split(",") if ansibleSkipTags >>>> != '' >>>> ansible.inventory_path = "../../inventory/full-dev-platform" >>>> end >>>> end >>>> >>>> >>>> On 18 December 2017 at 09:43, pele_smk <pele...@gmail.com> wrote: >>>> >>>>> Hey Gaurav, >>>>> I'm also in the process of building a single node VM. I'm running into >>>>> a different set of errors. If you would share your Vagrantfile and any >>>>> other changes to ansible or playbooks you made I'll replicate your setup >>>>> on my end and see if I hit the TLS issue and troubleshoot it from there. >>>>> >>>>> Thanks, >>>>> Daniel >>>>> >>>>> On Sun, Dec 17, 2017 at 7:02 PM, Gaurav Bapat <gauravb3...@gmail.com> >>>>> wrote: >>>>> >>>>>> Hi All, >>>>>> >>>>>> I have deployed Metron on single node on centOS 7.2 and used 16 GB >>>>>> RAM with i5 processor but I am stuck with some network issues. >>>>>> >>>>>> I am getting connection refused error(Error No 111), also when I >>>>>> check the logs it says TLS handshake failed. >>>>>> >>>>>> And when I restart all services, it gives me heartbeat lost error >>>>>> >>>>>> Please help, as I am not able to deploy Metron. >>>>>> >>>>>> Thanks, >>>>>> Gaurav >>>>>> >>>>> >>>>> >>>> -- >>> >>> Jon >>> >> >> -- > > Jon >
