Hi, I am not able to see public traffic icon itself to drag it to other nic On Nov 26, 2014 1:13 PM, "Nux!" <[email protected]> wrote:
> That should not be the case, you can pick up traffic types icons from your > left. Can you share some screenshots with us? > > -- > Sent from the Delta quadrant using Borg technology! > > Nux! > www.nux.ro > > ----- Original Message ----- > > From: "Tejas Sheth" <[email protected]> > > To: [email protected] > > Sent: Wednesday, 26 November, 2014 06:30:33 > > Subject: Re: security group and xenserver query > > > Hello, > > > > I have made the bridge configuration, but when i am selecting advance > > zone. it is not showing public network configuration. only guest and > > management is availabel. also internal CIDR ip configuration is also not > > available. > > i think it is cinverting to basic zone if we select security group and > > xenserver as hypervisor. > > > > Thanks > > Tejas > > > > On Tue, Nov 25, 2014 at 9:16 PM, Jayapal Reddy Uradi < > > [email protected]> wrote: > > > >> > >> For 6.2 you no need to install CSP. My typo mistake in last mail. > >> sysctl.conf is fine. > >> > >> > >> Thanks, > >> Jayapal > >> > >> On 25-Nov-2014, at 8:45 PM, Tejas Sheth <[email protected]> > >> wrote: > >> > >> > Thanks, > >> > > >> > So can i take it as confirmation and proceed with only following > bridge > >> > configuration in xenserver 6.2? > >> > > >> > # xe-switch-network-backend bridge > >> > > >> > # vi /etc/sysctl.conf > >> > net.bridge.bridge-nf-call-iptables = 1 > >> > net.bridge.bridge-nf-call-ip6tables = 0 > >> > net.bridge.bridge-nf-call-arptables = 1 > >> > > >> > # sysctl -p /etc/sysctl.conf > >> > > >> > Require confirmation for sysctl.cnf configuration part. > >> > > >> > Thanks and regards, > >> > Tejas > >> > > >> > On Tue, Nov 25, 2014 at 8:31 PM, Vadim Kimlaychuk < > >> [email protected] > >> >> wrote: > >> > > >> >> XenServer does not need any package to be expicitly installed. When > you > >> >> add host to CS it copies some files to the host itself and you don't > >> need > >> >> to bother about them usually. > >> >> > >> >> Vadim. > >> >> > >> >> -----Original Message----- > >> >> From: Tejas Sheth [mailto:[email protected]] > >> >> Sent: Tuesday, November 25, 2014 4:52 PM > >> >> To: [email protected] > >> >> Subject: security group and xenserver query > >> >> > >> >> Hello Jayapal, > >> >> > >> >> Thanks for reply, I have understood the bridge configuration part > but > >> >> can you clarify CSP package part. > >> >> > >> >> if CSP package comes with xenserver 6.2 then do we need to install > it > >> >> explicitly? > >> >> > >> >> It would be really helpful if you can send link to install CSP in > >> >> xenserver 6.2 because CS 4.3 document do not have description for > >> xenserver > >> >> 6.2 CSP installation. > >> >> ---------------------------------------------------------------- > >> >> Hi Tejas, > >> >> > >> >> The network mode set to 'bridge' mode. > >> >> #xe-switch-network-backend bridge > >> >> > >> >> I think Xenserver 6.2 comes with the CSP package, so you need to > install > >> >> it explicitly. > >> >> > >> >> > >> >> Thanks, > >> >> Jayapal > >> >> > >> >> > >> >> On 25-Nov-2014, at 4:47 PM, Tejas Sheth <[email protected]> > >> >> wrote: > >> >> > >> >>> Hello, > >> >>> > >> >>> We are configuring advanced zone in cloudstack 4.3 in xenserver > 6.2. > >> >>> we want to configure security group in advance zone. do we have to > do > >> >>> any special configuration in xenserver 6.2. > >> >>> > >> >>> xenserver has default networking configuration. > >> >>> > >> >>> Thanks and regards, > >> >>> Tejas > >> >> > >> >
