Hi Kristaps,
The operator will need to add two ranges to ACS.
1) /64 for the physical network (just as we do with public IPV4 at the moment),
this IPs will be used for the outside interface of the VRs
2) 1 or more /64 or larger (ideally /56s I'd say), which ACS will subnet into
/64s and assign them to the inside interfaces of the VRs.
Cheers
Alex
-----Original Message-----
From: Kristaps Cudars <kristaps.cud...@gmail.com>
Sent: 12 August 2021 10:37
To: d...@cloudstack.apache.org
Cc: users@cloudstack.apache.org
Subject: Re: IPV6 in Isolated/VPC networks
Hi Rohit,
I think its excellent and satisfies all involved sides.
We will be in front seats bringing this to production.
Suggestion:
This
* At the zone level root-admin specifies a /64 public range that will be
used for VRs, then
they can add a /48, or /56 IPv6 range for guest networks (to be used by
isolated networks and VPC tiers)
To
* At the zone level root-admin specifies a /64 public range that will be
used for VRs, then
they can add one or more ranges equal or larger than /64 IPv6 and ACS will
subnet it in /64s
for Isolated networks or VPC tiers.
Way:
RIPE NCC in case of PI (Provider Independent) range is granting /48 and its
important to have
possibility of assigning several subnets, for example /58 to be used for
internal /64 allocations.
If you want to extend your /48 you will need to have good explanation why you
want it.
RIPE NCC: Organisations requesting an IPv6 PI assignment larger than a /48 need
to provide
additional documentation to justify the larger assignment size.
The RIPE NCC will evaluate the PI assignment request and assign an independent
IPv6 prefix
to the End User organization directly.
On Wed, 11 Aug 2021 at 15:26, Rohit Yadav <rohit.ya...@shapeblue.com> wrote:
> Hi all,
>
> Thanks for your feedback and ideas, I've gone ahead with discussing
> them with Alex and came up with a PoC/design which can be implemented
> in the following phases:
>
> * Phase1: implement ipv6 support in isolated networks and VPC with
> static routing
> * Phase2: discuss and implement support for dynamic routing (TBD)
>
> For Phase1 here's the high-level proposal:
>
> * IPv6 address management:
> * At the zone level root-admin specifies a /64 public range that
> will be used for VRs, then they can add a /48, or /56 IPv6 range for
> guest networks (to be used by isolated networks and VPC tiers)
> * On creation of any IPv6 enabled isolated network or VPC tier,
> from the /48 or /56 block a /64 network is allocated/used
> * We assume SLAAC and autoconfiguration, no DHCPv6 in the zone
> (discuss: is privacy a concern, can privacy extensions rfc4941 of
> slaac be
> explored?)
> * Network offerings: root-admin can create new network offerings (with
> VPC too) that specifies a network stack option:
> * ipv4 only (default, for backward compatibility all
> networks/offerings post-upgrade migrate to this option)
> * ipv4-and-ipv6
> * ipv6-only (this can be phase 1.b)
> * A new routing option: static (phase1), dynamic (phase2, with
> multiple sub-options such as ospf/bgp etc...)
> * VR changes:
> * VR gets its guest and public nics set to inet6 auto
> * For each /64 allocated to guest network and VPC tiers, radvd is
> configured to do RA
> * Firewall: a new ipv6 zone/chain is created for ipv6 where ipv6
> firewall rules (ACLs, ingress, egress) are implemented; ACLs between
> VPC tiers are managed/implemented by ipv6 firewall on VR
> * It is assumed that static routes are created on the core/main
> router by the admin or automated using some scripts/tools; for this
> CloudStack will announce events with details of /64 networks and VR's
> public IPv6 address that can be consumed by a rabbitmq/message bus
> client (for example), or a custom cron job or script as part of orchestration.
> (this wouldn't be necessary for dynamic routing bgp with phase2)
> * Guest Networking: With SLAAC, it's easy for CloudStack to calculate
> allocate and use a /64 and determine the IPv6 address of VR nics and
> guest VM nics
> * A user create an isolated network/VPC with an offering that is
> ipv6 enabled
> * A user can manage firewall for the IPv6 address/guest nics;
> there'll be no port forward and LB feature though for IPv6
> * A users can run workloads in the guest VMs that listen on
> publically routable ipv6 addresses
> * Usage/billing etc continue to work, no change needed
>
> Network layout:
>
> [core/ISP router] -> [VR] -> [guest netwokr or VPC tier on a VLAN] ->
> [guest VMs/nics] *core/ISP router needs static routes to be added
> (manually or automated), assumes a /48 or /56 configured for the zone
>
> Thoughts, feedback?
>
> Proof-of-concept commentary: here's what I did to test the idea:
>
> * Created an isolated network and deployed a VM in my home lab
> The VR running on KVM has following nics
> eth0 - guest network
> eth1 - link local
> eth2 - public network
>
> * I setup a custom openwrt router on a RPi4 to serve as a toy-core
> router where I create a wan6 IPv6 tunnel using tunnel broker and I got
> a
> /48 allocated. My configuration looks like:
> /48 - 2001:470:ed36::/48 (allocated by tunnel broker)
> /64 - 2001:470:36:3e2::/64 (default allocated by)
>
> I create a LAN ipv6 (public network for CloudStack VR): at subnet/prefix 0:
> LAN IPv6 address: 2001:470:ed36:0::1/64 Address mode: SLAAC+stateless
> DHCP (no dhcpv6)
> *
> *
> In the isolated VR, I enabled ipv6 as:
> net.ipv6.conf.all.disable_ipv6 = 0
> net.ipv6.conf.all.forwarding = 1
> net.ipv6.conf.all.accept_ra = 1
> net.ipv6.conf.all.accept_redirects = 1 net.ipv6.conf.all.autoconf = 1
>
> Set up a IPv6 nameserver/dns in /etc/resolve.conf And configured the
> nics:
> echo iface eth0 inet6 auto >> /etc/network/interfaces echo iface eth2
> inet6 auto >> /etc/network/interfaces /etc/init.d/networking restart
> Next, restart ACS isolated network without cleanup to have it
> reconfigure
> IPv4 nics, firewall, NAT etc
>
> *
> Next, I created a /64 network for the isolated guest network on eth0
> of VR using radvd:
>
> # cat /etc/radvd.conf
> interface eth0
> {
> AdvSendAdvert on;
> MinRtrAdvInterval 5;
> MaxRtrAdvInterval 15;
> prefix 2001:470:ed36:1::/64
> {
> AdvOnLink on;
> AdvAutonomous on;
> };
> };
> systemctl restart radvd
> All guest VMs nics and VR's eth0 gets IPv6 address (SLAAC) in this
> ...:1::/64 network
> * Finally I added a static route in toy core-router for the new /64
> IPv6 range in the isolated network
> 2001:470:ed36:1::/64 via <public IPv6 address of the VR on eth2> dev
> <local lan nic>
> *
> ... and I enabled firewall rules to allow any traffic to pass for the
> new
> /64 network
>
> And voila all done! I create a domain AAAA record that points to my
> guest VM IPv6 address a test webserver on
> http://ipv6-isolated-ntwk-demo.yadav.cloud/
>
> (Note: I'll get rid of the tunnel and request a new /48 block after a
> few days, sharing this solely for testing purposes)
>
>
> Regards.
>
> ________________________________
> From: Wido den Hollander <w...@widodh.nl>
> Sent: Tuesday, July 20, 2021 12:46
> To: d...@cloudstack.apache.org <d...@cloudstack.apache.org>
> Subject: Re: IPV6 in Isolated/VPC networks
>
>
>
> Op 19-07-2021 om 20:38 schreef Kristaps Cudars:
> > Hi Wido,
> >
> > I assume that flouting ip will not work grate with ingress/egress
> > acl on
> VR.
> >
> > From regular ACS user perspective:
> > I have Instance with dualstack its running web app on 443.
> > I want to swap instances for whatever reason.
> > In case of IPv4 change d-nat rule.
> > In case of IPv6 if flouting IP was not created upfront he will need
> > to
> change dns entry that usually has 24h ttl. Inconvenience degradation
> in experience.
> >
>
> Yes, but, keep in mind that the IP you are using can also be
> terminated on the VR where HAProxy proxies request to the backend VM
> (could even be
> v4!)
>
> I'm not against DHCPv6, but I have seen many issues with implementing
> it. Therefor I always stick to SLAAC.
>
> > From ACS admin perspective:
> > I don’t want to have these tickets in helpdesk.
> > You needed to create another flouting IP that it would be seamless-
> > will
> not work as answer.
> >
>
> I understand that as well.
>
> Wido
>
> >
> > On 2021/07/19 09:05:54, Wido den Hollander <w...@widodh.nl> wrote:
> >>
> >>
> >> Op 16-07-2021 om 21:46 schreef Kristaps Cudars:
> >>> Hi Wido,
> >>>
> >>> Your proposal is to sacrifice ability to reassign IPv6 to
> >>> instance,
> have internal domain prefix, and list/db in ACS what IPv6 has been
> assigned to what instance and go with RA and SLAAC. For route
> signaling to switch use BGP/OSPFv3 or manual pre-creation.
> >>>
> >>
> >> You can still list the IPs which have been assigned. You'll know
> >> exactly what IPv6 address a VM has because of the prefix + MAC.
> >> Privacy Extensions need to be disabled in the VM.
> >>
> >> This already works in CloudStack in Shared Networks in this way.
> >>
> >> Using secondary IPs you can always have 'floating' IPv6 addressess.
> >>
> >> Wido
> >>
> >>> Option with RA and managed flag that DHCPv6 is in use to support
> preset information and ability to create route information from ACS is
> not an option as DHCPv6 its failing?
> >>>
> >>>
> >>> On 2021/07/16 15:17:42, Wido den Hollander <w...@widodh.nl> wrote:
> >>>>
> >>>>
> >>>> Op 16-07-2021 om 16:42 schreef Hean Seng:
> >>>>> Hi Wido,
> >>>>>
> >>>>> In current setup, each Cloudstack have own VR, so in this new
> >>>>> IPv6
> subnet
> >>>>> allocation , each VR (which have Frr) will need to have peering
> >>>>> with
> ISP
> >>>>> router (and either BGP or Static Route) , and there is 1000
> Acocunts, it
> >>>>> will 1000 BGP session with ISP router , Am I right for this ?
> >>>>> or I understand wrong .
> >>>>>
> >>>>
> >>>> Yes, that is correct. A /56 would also be sufficient or a /60
> >>>> which is enough to allocate a few /64 subnets.
> >>>>
> >>>> 1000 BGP connections isn't really a problem for a proper router
> >>>> at the ISP. OSPF(v3) would be better, but as I said that's poorly
> >>>> supported.
> >>>>
> >>>> The ISP could also install 1000 static routes, but that means
> >>>> that the ISP's router needs to have those configured.
> >>>>
> >>>> http://docs.frrouting.org/en/latest/ospf6d.html
> >>>> (While looking up this URL I see that Frr recently put in a lot
> >>>> of
> work
> >>>> in OSPFv3, seems better now)
> >>>>
> >>>>> I understand IPv6 is different then IPv4, and in IPv6 it suppose
> >>>>> each devices have own IP. It just how to realize in easy way.
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>
>
>
> > On Fri, Jul 16, 2021 at 8:17 PM Wido den Hollander <w...@widodh.nl>
> wrote:
> >>>>>
> >>>>>>
> >>>>>>
> >>>>>> Op 16-07-2021 om 05:54 schreef Hean Seng:
> >>>>>>> Hi Wido,
> >>>>>>>
> >>>>>>> My initial thought is not like this, it is the /48 at ISP
> >>>>>>> router,
> and
> >>>>>> /64
> >>>>>>> subnet assign to AdvanceZoneVR, AdvanceZoneVR responsible is
> >>>>>>> distribule IPv6 ip (from the assigned /64 sunet) to VM, and
> >>>>>>> not
> routing
> >>>>>>> the traffic, in the VM that get the IPv6 IP will default route
> to ISP
> >>>>>>> router as gw. It can may be a bridge over via Advancezone-VR.
> >>>>>>>
> >>>>>>
> >>>>>> How would you bridge this? That sounds like NAT?
> >>>>>>
> >>>>>> IPv6 is meant to be routed. Not to be translated or bridged in
> >>>>>> any
> way.
> >>>>>>
> >>>>>> The way a made the drawing is exactly how IPv6 should work in a
> >>>>>> VPC environment.
> >>>>>>
> >>>>>> Traffic flows through the VR where it can do firewalling of the
> traffic.
> >>>>>>
> >>>>>>> However, If do as the way described in the drawing, then i
> >>>>>>> suppose
> will
> >>>>>> be
> >>>>>>> another kind of virtual router going to introduce , to get
> >>>>>>> hold
> the /48
> >>>>>> in
> >>>>>>> this virtual router right ?
> >>>>>>>
> >>>>>>
> >>>>>> It can be the same VR. But keep in mind that IPv6 != IPv4.
> >>>>>>
> >>>>>> The VR will get Frr as a new daemon which can talk BGP with the
> upper
> >>>>>> network to route traffic.
> >>>>>>
> >>>>>>> After this, The Advance Zone, NAT's VR will peer with this
> >>>>>>> new
> IPv6 VR
> >>>>>>> for getting the IPv6 /64 prefix ?
> >>>>>>>
> >>>>>>
> >>>>>> IPv4 will be behind NAT, but IPv6 will not be behind NAT.
> >>>>>>
> >>>>>>> If do in this way, then I guess you just only need Static
> >>>>>>> route,
> with
> >>>>>>> peering ip both end as one /48 can have a lot of /64 on it.
> >>>>>>> And
> >>>>>> hardware
> >>>>>>> budgeting for new IPv6-VR will become very important, as all
> traffic will
> >>>>>>> need to pass over it .
> >>>>>>>
> >>>>>>
> >>>>>> Routing or NAT is the same for the VR. You don't need a very
> >>>>>> beefy
> VR
> >>>>>> for this.
> >>>>>>
> >>>>>>> It will be like
> >>>>>>>
> >>>>>>> ISP Router ------ > (new IPV6-VR ) ---- > AdvanceZone-VR
> >>>>>>> ----> VM
> >>>>>>>
> >>>>>>> Relationship of (new IPv6 VR) and AdvanceZone-VR , may be
> considering on
> >>>>>>> OSPF instead of BGP , otherwise few thousand of
> >>>>>>> AdvanceZone-VR
> wil have
> >>>>>>> few thousand of BGP session. on new-IPv6-VR
> >>>>>>>
> >>>>>>> Also, I suppose we cannot do ISP router. -->. Advancezone VR
> direct, ,
> >>>>>>> otherwise ISP router will be full of /64 prefix route either
> >>>>>>> on
> BGP( Many
> >>>>>>> BGP Session) , or Many Static route . If few thousand account,
> ti will
> >>>>>>> be few thousand of BGP session with ISP router or few thousand
> static
> >>>>>> route
> >>>>>>> which is not possible .
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>> On Thu, Jul 15, 2021 at 10:47 PM Wido den Hollander <
> w...@widodh.nl>
> >>>>>> wrote:
> >>>>>>>
> >>>>>>>> But you still need routing. See the attached PNG (and draw.io
> XML).
> >>>>>>>>
> >>>>>>>> You need to route the /48 subnet TO the VR which can then
> >>>>>>>> route
> it to
> >>>>>>>> the Virtual Networks behind the VR.
> >>>>>>>>
> >>>>>>>> There is no other way then routing with either BGP or a
> >>>>>>>> Static
> route.
> >>>>>>>>
> >>>>>>>> Wido
> >>>>>>>>
> >>>>>>>> Op 15-07-2021 om 12:39 schreef Hean Seng:
> >>>>>>>>> Or explain like this :
> >>>>>>>>>
> >>>>>>>>> 1) Cloudstack generate list of /64 subnet from /48 that
> >>>>>>>>> Network
> admin
> >>>>>>>>> assigned to Cloudstack
> >>>>>>>>> 2) Cloudsack allocated the subnet (that generated from
> >>>>>>>>> step1) to
> >>>>>> Virtual
> >>>>>>>>> Router, one Virtual Router have one subniet /64
> >>>>>>>>> 3) Virtual Router allocate single IPv6 (within the range of
> >>>>>>>>> /64 allocated to VR) to VM
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> On Thu, Jul 15, 2021 at 6:25 PM Hean Seng
> >>>>>>>>> <heans...@gmail.com <mailto:heans...@gmail.com>> wrote:
> >>>>>>>>>
> >>>>>>>>> Hi Wido,
> >>>>>>>>>
> >>>>>>>>> I think the /48 is at physical router as gateway ,
> >>>>>>>>> and
> subnet of
> >>>>>> /64
> >>>>>>>>> at VR of Cloudstack. Cloudstack only keep which /48
> prefix and
> >>>>>>>>> vlan information of this /48 to be later split the /64.
> to VR.
> >>>>>>>>>
> >>>>>>>>> And the instances is getting singe IPv6 of /64 IP.
> The VR is
> >>>>>>>>> getting /64. The default gateway shall goes to /48
> >>>>>>>>> of
> physical
> >>>>>>>>> router ip . In this case ,does not need any BGP router
> .
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> Similar concept as IPv4 :
> >>>>>>>>>
> >>>>>>>>> /48 subnet of IPv6 is equivalent to current /24
> >>>>>>>>> subnet
> of IPv4
> >>>>>> that
> >>>>>>>>> created in Network.
> >>>>>>>>> and /64 of IPv6 is equivalent to single IP of IPv4
> assign to VM.
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> On Thu, Jul 15, 2021 at 5:31 PM Wido den Hollander <
> >>>>>> w...@widodh.nl
> >>>>>>>>> <mailto:w...@widodh.nl>> wrote:
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> Op 14-07-2021 om 16:44 schreef Hean Seng:
> >>>>>>>>> > Hi
> >>>>>>>>> >
> >>>>>>>>> > I replied in another thread, i think do not
> >>>>>>>>> need
> implement
> >>>>>>>>> BGP or OSPF,
> >>>>>>>>> > that would be complicated .
> >>>>>>>>> >
> >>>>>>>>> > We only need assign IPv6 's /64 prefix to
> Virtual Router
> >>>>>>>>> (VR) in NAT
> >>>>>>>>> > zone, and the VR responsible to deliver
> >>>>>>>>> single
> IPv6 to VM
> >>>>>> via
> >>>>>>>>> DHCP6.
> >>>>>>>>> >
> >>>>>>>>> > In VR, you need to have Default IPv6 route to
> Physical
> >>>>>>>>> Router's /48. IP
> >>>>>>>>> > as IPv6 Gateway. Thens should be done .
> >>>>>>>>> >
> >>>>>>>>> > Example :
> >>>>>>>>> > Physical Router Interface
> >>>>>>>>> > IPv6 IP : 2000:aaaa::1/48
> >>>>>>>>> >
> >>>>>>>>> > Cloudstack virtual router :
> 2000:aaaa:200:201::1/64 with
> >>>>>>>>> default ipv6
> >>>>>>>>> > route to router ip 2000:aaaa::1
> >>>>>>>>> > and Clodustack Virtual router dhcp allocate
> >>>>>>>>> IP to
> VM , and
> >>>>>>>>> VM will have
> >>>>>>>>> > default route to VR. IPv6 2000:aaaa:200:201::1
> >>>>>>>>> >
> >>>>>>>>> > So in cloudstack need to allow user to enter
> >>>>>>>>> ,
> IPv6
> >>>>>>>>> gwateway , and
> >>>>>>>>> > the /48 Ipv6 prefix , then it will self
> >>>>>>>>> allocate
> the /64
> >>>>>> ip
> >>>>>>>>> to the VR ,
> >>>>>>>>> > and maintain make sure not ovelap allocation
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>>
> >>>>>>>>> But NAT is truly not the solution with IPv6.
> >>>>>>>>> IPv6 is
> supposed
> >>>>>> to
> >>>>>>>> be
> >>>>>>>>> routable. In addition you should avoid DHCPv6 as
> much as
> >>>>>>>>> possible as
> >>>>>>>>> that's not really the intended use-case for
> >>>>>>>>> address
> allocation
> >>>>>>>>> with IPv6.
> >>>>>>>>>
> >>>>>>>>> In order to route an /48 IPv6 subnet to the VR
> >>>>>>>>> you
> have a few
> >>>>>>>>> possibilities:
> >>>>>>>>>
> >>>>>>>>> - Static route from the upperlying routers which
> >>>>>>>>> are
> outside
> >>>>>> of
> >>>>>>>>> CloudStack
> >>>>>>>>> - BGP
> >>>>>>>>> - OSPFv3 (broken in most cases!)
> >>>>>>>>> - DHCPv6 Prefix Delegation
> >>>>>>>>>
> >>>>>>>>> BGP and/or Static routes are still the best bet here.
> >>>>>>>>>
> >>>>>>>>> So what you do is that you tell CloudStack that
> >>>>>>>>> you
> will route
> >>>>>>>>> 2001:db8::/48 to the VR, the VR can then use
> >>>>>>>>> that to
> split it
> >>>>>> up
> >>>>>>>>> into
> >>>>>>>>> multiple /64 subnets going towards the instances:
> >>>>>>>>>
> >>>>>>>>> - 2001:db8::/64
> >>>>>>>>> - 2001:db8:1::/64
> >>>>>>>>> - 2001:db8:2::/64
> >>>>>>>>> ...
> >>>>>>>>> - 2001:db8:f::/64
> >>>>>>>>>
> >>>>>>>>> And go on.
> >>>>>>>>>
> >>>>>>>>> In case of BGP you indeed have to tell the VR a
> >>>>>>>>> few
> things:
> >>>>>>>>>
> >>>>>>>>> - It's own AS number
> >>>>>>>>> - The peer's address(es)
> >>>>>>>>>
> >>>>>>>>> With FRR you can simply say:
> >>>>>>>>>
> >>>>>>>>> neighbor 2001:db8:4fa::179 remote-as external
> >>>>>>>>>
> >>>>>>>>> The /48 you need to have at the VR anyway in
> >>>>>>>>> case of
> either a
> >>>>>>>>> static
> >>>>>>>>> route or BGP.
> >>>>>>>>>
> >>>>>>>>> We just need to add a NullRoute on the VR for
> >>>>>>>>> that
> /48 so that
> >>>>>>>>> traffic
> >>>>>>>>> will not be routed to the upper gateway in case
> >>>>>>>>> of
> the VR
> >>>>>> can't
> >>>>>>>>> find a
> >>>>>>>>> route.
> >>>>>>>>>
> >>>>>>>>> Wido
> >>>>>>>>>
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> > On Wed, Jul 14, 2021 at 8:55 PM Alex Mattioli
> >>>>>>>>> > <alex.matti...@shapeblue.com
> >>>>>>>>> <mailto:alex.matti...@shapeblue.com>
> >>>>>>>>> <mailto:alex.matti...@shapeblue.com
> >>>>>>>>> <mailto:alex.matti...@shapeblue.com>>> wrote:
> >>>>>>>>> >
> >>>>>>>>> > Hi Wido,
> >>>>>>>>> > That's pretty much in line with our thoughts,
> thanks
> >>>>>> for
> >>>>>>>>> the input.
> >>>>>>>>> > I believe we agree on the following points
> then:
> >>>>>>>>> >
> >>>>>>>>> > - FRR with BGP (no OSPF)
> >>>>>>>>> > - Route /48 (or/56) down to the VR
> >>>>>>>>> > - /64 per network
> >>>>>>>>> > - SLACC for IP addressing
> >>>>>>>>> >
> >>>>>>>>> > I believe the next big question is then "on
> which level
> >>>>>>>>> of ACS do we
> >>>>>>>>> > manage AS numbers?". I see two options:
> >>>>>>>>> > 1) Private AS number on a per-zone basis
> >>>>>>>>> > 2) Root Admin assigned AS number on a
> domain/account
> >>>>>> basis
> >>>>>>>>> > 3) End-user driven AS number on a per network
> basis
> >>>>>> (for
> >>>>>>>>> bring your
> >>>>>>>>> > own AS and IP scenario)
> >>>>>>>>> >
> >>>>>>>>> > Thoughts?
> >>>>>>>>> >
> >>>>>>>>> > Cheers
> >>>>>>>>> > Alex
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> > -----Original Message-----
> >>>>>>>>> > From: Wido den Hollander <w...@widodh.nl
> >>>>>>>>> <mailto:w...@widodh.nl> <mailto:w...@widodh.nl
> >>>>>>>>> <mailto:w...@widodh.nl>>>
> >>>>>>>>> > Sent: 13 July 2021 15:08
> >>>>>>>>> > To: d...@cloudstack.apache.org
> >>>>>>>>> <mailto:d...@cloudstack.apache.org>
> >>>>>>>>> <mailto:d...@cloudstack.apache.org
> >>>>>>>>> <mailto:d...@cloudstack.apache.org>>;
> >>>>>>>>> > Alex Mattioli <alex.matti...@shapeblue.com
> >>>>>>>>> <mailto:alex.matti...@shapeblue.com>
> >>>>>>>>> > <mailto:alex.matti...@shapeblue.com
> >>>>>>>>> <mailto:alex.matti...@shapeblue.com>>>
> >>>>>>>>> > Cc: Wei Zhou <wei.z...@shapeblue.com
> >>>>>>>>> <mailto:wei.z...@shapeblue.com>
> >>>>>>>>> > <mailto:wei.z...@shapeblue.com
> >>>>>>>>> <mailto:wei.z...@shapeblue.com>>>; Rohit Yadav
> >>>>>>>>> > <rohit.ya...@shapeblue.com
> >>>>>>>>> <mailto:rohit.ya...@shapeblue.com>
> >>>>>>>>> <mailto:rohit.ya...@shapeblue.com
> >>>>>>>>> <mailto:rohit.ya...@shapeblue.com>>>;
> >>>>>>>>> > Gabriel Beims Bräscher <gabr...@pcextreme.nl
> >>>>>>>>> <mailto:gabr...@pcextreme.nl>
> >>>>>>>>> > <mailto:gabr...@pcextreme.nl <mailto:
> >>>>>> gabr...@pcextreme.nl
> >>>>>>>>>>>
> >>>>>>>>> > Subject: Re: IPV6 in Isolated/VPC networks
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> > On 7/7/21 1:16 PM, Alex Mattioli wrote:
> >>>>>>>>> > > Hi all,
> >>>>>>>>> > > @Wei Zhou<mailto:wei.z...@shapeblue.com
> >>>>>>>>> <mailto:wei.z...@shapeblue.com>
> >>>>>>>>> > <mailto:wei.z...@shapeblue.com
> >>>>>>>>> <mailto:wei.z...@shapeblue.com>>> @Rohit
> >>>>>>>>> > Yadav<mailto:rohit.ya...@shapeblue.com
> >>>>>>>>> <mailto:rohit.ya...@shapeblue.com>
> >>>>>>>>> > <mailto:rohit.ya...@shapeblue.com
> >>>>>>>>> <mailto:rohit.ya...@shapeblue.com>>> and myself are
> >>>>>>>>> investigating how
> >>>>>>>>> > to enable IPV6 support on Isolated and VPC
> networks and
> >>>>>>>>> would like
> >>>>>>>>> > your input on it.
> >>>>>>>>> > > At the moment we are looking at
> implementing FRR
> >>>>>> with
> >>>>>>>>> BGP (and
> >>>>>>>>> > possibly OSPF) on the ACS VR.
> >>>>>>>>> > >
> >>>>>>>>> > > We are looking for requirements,
> recommendations,
> >>>>>>>>> ideas, rants,
> >>>>>>>>> > etc...etc...
> >>>>>>>>> > >
> >>>>>>>>> >
> >>>>>>>>> > Ok! Here we go.
> >>>>>>>>> >
> >>>>>>>>> > I think that you mean that the VR will
> actually route
> >>>>>> the
> >>>>>>>>> IPv6
> >>>>>>>>> > traffic and for that you need to have a way
> of getting
> >>>>>> a
> >>>>>>>>> subnet
> >>>>>>>>> > routed to the VR.
> >>>>>>>>> >
> >>>>>>>>> > BGP is probably you best bet here. Although
> OSPFv3
> >>>>>>>>> technically
> >>>>>>>>> > supports this it is very badly implemented in
> Frr for
> >>>>>>>>> example.
> >>>>>>>>> >
> >>>>>>>>> > Now FRR is a very good router and one of the
> fancy
> >>>>>>>>> features it
> >>>>>>>>> > supports is BGP Unnumered. This allows for
> auto
> >>>>>>>>> configuration of BGP
> >>>>>>>>> > over a L2 network when both sides are sending
> Router
> >>>>>>>>> Advertisements.
> >>>>>>>>> > This is very easy for flexible BGP
> configurations where
> >>>>>>>>> both sides
> >>>>>>>>> > have dynamic IPs.
> >>>>>>>>> >
> >>>>>>>>> > What you want to do is that you get a /56,
> /48 or
> >>>>>>>>> something which is
> >>>>>>>>> > >/64 bits routed to the VR.
> >>>>>>>>> >
> >>>>>>>>> > Now you can sub-segment this into separate
> /64 subnets.
> >>>>>>>>> You don't
> >>>>>>>>> > want to go smaller then a /64 is that
> prevents you from
> >>>>>>>>> using SLAAC
> >>>>>>>>> > for IPv6 address configuration. This is how
> it works
> >>>>>> for
> >>>>>>>>> Shared
> >>>>>>>>> > Networks now in Basic and Advanced Zones.
> >>>>>>>>> >
> >>>>>>>>> > FRR can now also send out the Router
> Advertisements on
> >>>>>>>>> the downlinks
> >>>>>>>>> > sending out:
> >>>>>>>>> >
> >>>>>>>>> > - DNS servers
> >>>>>>>>> > - DNS domain
> >>>>>>>>> > - Prefix (/64) to be used
> >>>>>>>>> >
> >>>>>>>>> > There is no need for DHCPv6. You can
> calculate the IPv6
> >>>>>>>>> address the
> >>>>>>>>> > VM will obtain by using the MAC and the
> prefix.
> >>>>>>>>> >
> >>>>>>>>> > So in short:
> >>>>>>>>> >
> >>>>>>>>> > - Using BGP you routed a /48 to the VR
> >>>>>>>>> > - Now you split this into /64 subnets towards
> the
> >>>>>>>>> isolated networks
> >>>>>>>>> >
> >>>>>>>>> > Wido
> >>>>>>>>> >
> >>>>>>>>> > > Alex Mattioli
> >>>>>>>>> > >
> >>>>>>>>> > >
> >>>>>>>>> > >
> >>>>>>>>> > >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> >
> >>>>>>>>> > --
> >>>>>>>>> > Regards,
> >>>>>>>>> > Hean Seng
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> --
> >>>>>>>>> Regards,
> >>>>>>>>> Hean Seng
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> --
> >>>>>>>>> Regards,
> >>>>>>>>> Hean Seng
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>
> >>>>>
> >>>>>
> >>>>
> >>
