On Wed, 2018-06-27 at 07:41 +0200, Ulrich Windl wrote: > > > > Ken Gaillot <kgail...@redhat.com> schrieb am 26.06.2018 um > > > > 18:22 in Nachricht > > <1530030128.5202.5.ca...@redhat.com>: > > On Tue, 2018-06-26 at 10:45 +0300, Vladislav Bogdanov wrote: > > > 26.06.2018 09:14, Ulrich Windl wrote: > > > > Hi! > > > > > > > > We just observed some strange effect we cannot explain in SLES > > > > 11 > > > > SP4 (pacemaker 1.1.12-f47ea56): > > > > We run about a dozen of Xen PVMs on a three-node cluster (plus > > > > some > > > > infrastructure and monitoring stuff). It worked all well so > > > > far, > > > > and there was no significant change recently. > > > > However when a colleague stopped on VM for maintenance via > > > > cluster > > > > command, the cluster did not notice when the PVM actually was > > > > running again (it had been started not using the cluster (a bad > > > > idea, I know)). > > > > > > To be on a safe side in such cases you'd probably want to enable > > > additional monitor for a "Stopped" role. Default one covers only > > > "Started" role. The same thing as for multistate resources, where > > > you > > > need several monitor ops, for "Started/Slave" and "Master" roles. > > > But, this will increase a load. > > > And, I believe cluster should reprobe a resource on all nodes > > > once > > > you > > > change target-role back to "Started". > > > > Which raises the question, how did you stop the VM initially? > > I thought "(...) stopped one VM for maintenance via cluster command" > is obvious. It was something like "crm resource stop ...". > > > > > If you stopped it by setting target-role to Stopped, likely the > > cluster > > still thinks it's stopped, and you need to set it to Started again. > > If > > instead you set maintenance mode or unmanaged the resource, then > > stopped the VM manually, then most likely it's still in that mode > > and > > needs to be taken out of it. > > The point was when the command to start the resource was given, the > cluster had completely ignored the fact that it was running already > and started to start the VM on a second node (which may be > desastrous). But that's leading away from the main question...
Ah, this is expected behavior when you start a resource manually, and there are no monitors with target-role=Stopped. If the node where you manually started the VM isn't the same node the cluster happens to choose, then you can get multiple active instances. By default, the cluster assumes that where a probe found a resource to be not running, that resource will stay not running unless started by the cluster. (It will re-probe if the node goes away and comes back.) If you wish to guard against resources being started outside cluster control, configure a recurring monitor with target-role=Stopped, and the cluster will run that on all nodes where it thinks the resource is not supposed to be running. Of course since it has to poll at intervals, it can take up to that much time to detect a manually started instance. > > > > Examining the logs, it seems that the recheck timer popped > > > > periodically, but no monitor action was run for the VM (the > > > > action > > > > is configured to run every 10 minutes). Recurring monitors are only recorded in the log if their return value changed. If there are 10 successful monitors in a row and then a failure, only the first success and the failure are logged. > > > > > > > > Actually the only monitor operations found were: > > > > May 23 08:04:13 > > > > Jun 13 08:13:03 > > > > Jun 25 09:29:04 > > > > Then a manual "reprobe" was done, and several monitor > > > > operations > > > > were run. > > > > Then again I see no more monitor actions in syslog. > > > > > > > > What could be the reasons for this? Too many operations > > > > defined? > > > > > > > > The other message I don't understand is like "<other-resource>: > > > > Rolling back scores from <vm-resource>" > > > > > > > > Could it be a new bug introduced in pacemaker, or could it be > > > > some > > > > configuration problem (The status is completely clean however)? > > > > > > > > According to the packet changelog, there was no change since > > > > Nov > > > > 2016... > > > > > > > > Regards, > > > > Ulrich -- Ken Gaillot <kgail...@redhat.com> _______________________________________________ Users mailing list: Users@clusterlabs.org https://lists.clusterlabs.org/mailman/listinfo/users Project Home: http://www.clusterlabs.org Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf Bugs: http://bugs.clusterlabs.org
