Hmm, the Realtek interface is the cause of the interrupt storm. So the timer probably is not working. Try following: sysctl net.ifpoll.0.pollhz=1000 sysctl net.ifpoll.1.pollhz=1000 ifconfig re0 polling
Thanks, sephe On Thu, Apr 20, 2017 at 11:18 PM, Predrag Punosevac <[email protected]> wrote: > Sepherosa Ziehau <[email protected]> wrote: > >> Can you post the dmesg and vmstat -iv? I think for ahci controller, >> MSI will be used by default. > > dfly# vmstat -iv > interrupt total rate > irq1 0: atkbd0 1 0 > irq3 0: sio1 0 0 > irq4 0: sio0 0 0 > irq9 0: acpi0 0 0 > irq11 0: ehci0/ehci1 274707 1 > irq16 0: re0 168712 1 > irq192 0: swi_siopoll 0 0 > irq196 0: swi_vm 0 0 > irq16 1: ahci0 1495360 9 > irq195 1: swi_cambio 752050 4 > irq197 1: swi_mp_taskq/swi_taskq 0 0 > Total 2690830 17 > > > > > > > Copyright (c) 2003-2017 The DragonFly Project. > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017 > [email protected]:/usr/obj/usr/src/sys/X86_64_GENERIC > i8254 clock: 1193296 Hz > TSC invariant clock: 1795934280 Hz > CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB> > Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM> > MONITOR/MWAIT Features=0x3<CST,INTBRK> > real memory = 8477464576 (8084 MB) > avail memory = 7884136448 (7518 MB) > lapic: divisor index 0, frequency 49886793 Hz > srat_probe: can't locate SRAT > Initialize MI interrupts > TSC testing MP synchronization ... > cpu1: TSC is not MP synchronized @0 > TSC is not MP synchronized > VMM: available, disabled by default > wdog: In-kernel automatic watchdog reset enabled > kbd1 at kbdmux0 > md0: Malloc disk > interrupt uses mplock: swi_taskq > ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA) > ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I 01072009 AMI > 00010013) > ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I 00000028 INTL > 20051117) > ACPI: FACS 0x00000000DABB7080 000040 > ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I 01072009 MSFT > 00000097) > ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I 01072009 AMI. > 00000005) > ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL > 20091112) > ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef Cpu0Ist 00003000 INTL > 20051117) > ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef CpuPm 00003000 INTL > 20051117) > cryptosoft0: <software crypto> on motherboard > aesni0: No AESNI support. > padlock0: No ACE support. > rdrand0: No RdRand support. > acpi0: <ALASKA A M I> on motherboard > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: 4 ACPI AML tables successfully acquired and loaded > ACPI FADT: SCI testing interrupt mode ... > ACPI FADT: SCI select level/high > acpi0: Power Button (fixed) > acpi_timer0 on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > acpi_hpet0: frequency 14318180 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0 > vgapci0: Boot video device > pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16 > ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 16 at device 26.0 on pci0 > usbus0: EHCI version 1.0 > usbus0 on ehci0 > pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22 > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > usbus0: 480Mbps High Speed USB v2.0 > pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem > 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2 > re0: MAC version 0x2c900000, MACFG 39, support MSI > re0: bus speed 125MHz > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > re0: MAC address: b8:ae:ed:3c:ce:35 > ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 23 at device 29.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > ahci0: <AHCI-PCI-SATA> port > 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem > 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0 > usbus1: 480Mbps High Speed USB v2.0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > ahci0: Intel hocus pocus > ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 > 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps) > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > ugen1.3: <DELL> at usbus1 > ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on > usbus1 > kbd2 at ukbd0 > ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018" > ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES > capacity=30533.83MB > ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen > ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584" > ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282" > ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.5: No device detected > pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18 > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > cpu0: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef Cpu0Cst 00003001 INTL > 20051117) > cpu_cst0: <ACPI CPU C-State> on cpu0 > cpu_pst0: <ACPI CPU P-State> on cpu0 > clockmod0: <CPU clock modulation> on cpu0 > perfbias0: <CPU perf-energy bias> on cpu0 > coretemp0: <CPU On-Die Thermal Sensors> on cpu0 > cpu1: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef ApIst 00003000 INTL > 20051117) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef ApCst 00003000 INTL > 20051117) > cpu_cst1: <ACPI CPU C-State> on cpu1 > cpu_pst1: <ACPI CPU P-State> on cpu1 > clockmod1: <CPU clock modulation> on cpu1 > perfbias1: <CPU perf-energy bias> on cpu1 > coretemp1: <CPU On-Die Thermal Sensors> on cpu1 > ACPI: Enabled 6 GPEs in block 00 to 3F > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x500 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > hpt27xx: no controller detected. > CAM: Configuring 4 busses > CAM: finished configuring all busses > da0 at ahci0 bus 0 target 0 lun 0 > da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device > da0: Serial Number B620550018 > da0: 600.000MB/s transfers > da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C) > da0: supports TRIM > da1 at ahci0 bus 2 target 0 lun 0 > da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da1: Serial Number WD-WCAWZ2969584 > da1: 300.000MB/s transfers > da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da2 at ahci0 bus 4 target 0 lun 0 > da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da2: Serial Number WD-WCAWZ2111282 > da2: 300.000MB/s transfers > da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da1 part 0: unavailable, bad start or ending lba > da2 part 0: unavailable, bad start or ending lba > no B_DEVMAGIC (bootdev=0) > Mounting root from hammer:serno/B620550018.s1d > HAMMER(ROOT) recovery check seqno=0899bed3 > HAMMER(ROOT) recovery range 3000000014442e30-3000000014442e30 > HAMMER(ROOT) recovery nexto 3000000014442e30 endseqno=0899bed4 > HAMMER(ROOT) mounted clean, no recovery needed > DMA space used: 10428k, remaining available: 131072k > Mounting devfs > HAMMER(DATA) recovery check seqno=2fa25c1d > HAMMER(DATA) recovery range 3000000034605ad0-3000000034605ad0 > HAMMER(DATA) recovery nexto 3000000034605ad0 endseqno=2fa25c1e > HAMMER(DATA) mounted clean, no recovery needed > HAMMER(BACKUP) recovery check seqno=040a1f5b > HAMMER(BACKUP) recovery range 300000003034ce98-300000003034ce98 > HAMMER(BACKUP) recovery nexto 300000003034ce98 endseqno=040a1f5c > HAMMER(BACKUP) mounted clean, no recovery needed > swap low/high-water marks set to 67683/101525 > pflog0: promiscuous mode enabled > boot() called on cpu#1 > Switching to cpu #0 for shutdown > Waiting (max 60 seconds) for system thread swapcached to stop...stopped > Waiting (max 60 seconds) for system thread vnlru to stop...stopped > Waiting (max 60 seconds) for system thread consttyd to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped > > syncing disks... 137 105 105 > done > Copyright (c) 2003-2017 The DragonFly Project. > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017 > [email protected]:/usr/obj/usr/src/sys/X86_64_GENERIC > i8254 clock: 1193300 Hz > TSC invariant clock: 1795933432 Hz > CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB> > Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM> > MONITOR/MWAIT Features=0x3<CST,INTBRK> > real memory = 8477464576 (8084 MB) > avail memory = 7884136448 (7518 MB) > lapic: divisor index 0, frequency 49886884 Hz > srat_probe: can't locate SRAT > Initialize MI interrupts > TSC testing MP synchronization ... > cpu1: TSC is not MP synchronized @0 > TSC is not MP synchronized > VMM: available, disabled by default > wdog: In-kernel automatic watchdog reset enabled > kbd1 at kbdmux0 > md0: Malloc disk > interrupt uses mplock: swi_taskq > ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA) > ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I 01072009 AMI > 00010013) > ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I 00000028 INTL > 20051117) > ACPI: FACS 0x00000000DABB7080 000040 > ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I 01072009 MSFT > 00000097) > ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I 01072009 AMI. > 00000005) > ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL > 20091112) > ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef Cpu0Ist 00003000 INTL > 20051117) > ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef CpuPm 00003000 INTL > 20051117) > cryptosoft0: <software crypto> on motherboard > aesni0: No AESNI support. > padlock0: No ACE support. > rdrand0: No RdRand support. > acpi0: <ALASKA A M I> on motherboard > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: 4 ACPI AML tables successfully acquired and loaded > ACPI FADT: SCI testing interrupt mode ... > ACPI FADT: SCI select level/high > acpi0: Power Button (fixed) > acpi_timer0 on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > acpi_hpet0: frequency 14318180 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0 > vgapci0: Boot video device > pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16 > ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 16 at device 26.0 on pci0 > usbus0: EHCI version 1.0 > usbus0 on ehci0 > pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22 > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > usbus0: 480Mbps High Speed USB v2.0 > pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem > 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2 > re0: MAC version 0x2c900000, MACFG 39, support MSI > re0: bus speed 125MHz > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > re0: MAC address: b8:ae:ed:3c:ce:35 > ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 23 at device 29.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > ahci0: <AHCI-PCI-SATA> port > 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem > 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0 > usbus1: 480Mbps High Speed USB v2.0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > ahci0: Intel hocus pocus > ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 > 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps) > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > ugen1.3: <DELL> at usbus1 > ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on > usbus1 > kbd2 at ukbd0 > ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018" > ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES > capacity=30533.83MB > ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen > ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584" > ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282" > ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.5: No device detected > pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18 > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > cpu0: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef Cpu0Cst 00003001 INTL > 20051117) > cpu_cst0: <ACPI CPU C-State> on cpu0 > cpu_pst0: <ACPI CPU P-State> on cpu0 > clockmod0: <CPU clock modulation> on cpu0 > perfbias0: <CPU perf-energy bias> on cpu0 > coretemp0: <CPU On-Die Thermal Sensors> on cpu0 > cpu1: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef ApIst 00003000 INTL > 20051117) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef ApCst 00003000 INTL > 20051117) > cpu_cst1: <ACPI CPU C-State> on cpu1 > cpu_pst1: <ACPI CPU P-State> on cpu1 > clockmod1: <CPU clock modulation> on cpu1 > perfbias1: <CPU perf-energy bias> on cpu1 > coretemp1: <CPU On-Die Thermal Sensors> on cpu1 > ACPI: Enabled 6 GPEs in block 00 to 3F > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x500 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > hpt27xx: no controller detected. > CAM: Configuring 4 busses > CAM: finished configuring all busses > da0 at ahci0 bus 0 target 0 lun 0 > da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device > da0: Serial Number B620550018 > da0: 600.000MB/s transfers > da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C) > da0: supports TRIM > da1 at ahci0 bus 2 target 0 lun 0 > da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da1: Serial Number WD-WCAWZ2969584 > da1: 300.000MB/s transfers > da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da2 at ahci0 bus 4 target 0 lun 0 > da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da2: Serial Number WD-WCAWZ2111282 > da2: 300.000MB/s transfers > da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da1 part 0: unavailable, bad start or ending lba > da2 part 0: unavailable, bad start or ending lba > no B_DEVMAGIC (bootdev=0) > Mounting root from hammer:serno/B620550018.s1d > HAMMER(ROOT) recovery check seqno=0899cf95 > HAMMER(ROOT) recovery range 3000000014612ea8-3000000014612ea8 > HAMMER(ROOT) recovery nexto 3000000014612ea8 endseqno=0899cf96 > HAMMER(ROOT) mounted clean, no recovery needed > DMA space used: 10428k, remaining available: 131072k > Mounting devfs > HAMMER(DATA) recovery check seqno=2fa3a14d > HAMMER(DATA) recovery range 3000000036618778-3000000036618778 > HAMMER(DATA) recovery nexto 3000000036618778 endseqno=2fa3a14e > HAMMER(DATA) mounted clean, no recovery needed > HAMMER(BACKUP) recovery check seqno=040a2f3c > HAMMER(BACKUP) recovery range 300000003051ff80-300000003051ff80 > HAMMER(BACKUP) recovery nexto 300000003051ff80 endseqno=040a2f3d > HAMMER(BACKUP) mounted clean, no recovery needed > swap low/high-water marks set to 67683/101525 > pflog0: promiscuous mode enabled > boot() called on cpu#0 > Waiting (max 60 seconds) for system thread swapcached to stop...stopped > Waiting (max 60 seconds) for system thread vnlru to stop...stopped > Waiting (max 60 seconds) for system thread consttyd to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped > > syncing disks... > done > vflush: Warning, cannot destroy busy device vnode > unmount of filesystem mounted from devfs failed (BUSY) > unmount(0xffffff81d6e23cc0): Forced unmount: 0 namecache references still > present > unmount(0xffffff81d6e23cc0): Forced unmount: 1 mount refs still present > Copyright (c) 2003-2017 The DragonFly Project. > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017 > [email protected]:/usr/obj/usr/src/sys/X86_64_GENERIC > i8254 clock: 1193291 Hz > TSC invariant clock: 1795935104 Hz > CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.94-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB> > Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM> > MONITOR/MWAIT Features=0x3<CST,INTBRK> > real memory = 8477464576 (8084 MB) > avail memory = 7884136448 (7518 MB) > lapic: divisor index 0, frequency 49886870 Hz > srat_probe: can't locate SRAT > Initialize MI interrupts > TSC testing MP synchronization ... > cpu1: TSC is not MP synchronized @0 > TSC is not MP synchronized > VMM: available, disabled by default > wdog: In-kernel automatic watchdog reset enabled > kbd1 at kbdmux0 > md0: Malloc disk > interrupt uses mplock: swi_taskq > ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA) > ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I 01072009 AMI > 00010013) > ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I 00000028 INTL > 20051117) > ACPI: FACS 0x00000000DABB7080 000040 > ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I 01072009 MSFT > 00000097) > ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I 01072009 AMI. > 00000005) > ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL > 20091112) > ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef Cpu0Ist 00003000 INTL > 20051117) > ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef CpuPm 00003000 INTL > 20051117) > cryptosoft0: <software crypto> on motherboard > aesni0: No AESNI support. > padlock0: No ACE support. > rdrand0: No RdRand support. > acpi0: <ALASKA A M I> on motherboard > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: 4 ACPI AML tables successfully acquired and loaded > ACPI FADT: SCI testing interrupt mode ... > ACPI FADT: SCI select level/high > acpi0: Power Button (fixed) > acpi_timer0 on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > acpi_hpet0: frequency 14318180 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0 > vgapci0: Boot video device > pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16 > ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 16 at device 26.0 on pci0 > usbus0: EHCI version 1.0 > usbus0 on ehci0 > pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22 > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > usbus0: 480Mbps High Speed USB v2.0 > pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem > 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2 > re0: MAC version 0x2c900000, MACFG 39, support MSI > re0: bus speed 125MHz > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > re0: MAC address: b8:ae:ed:3c:ce:35 > ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 23 at device 29.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > ahci0: <AHCI-PCI-SATA> port > 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem > 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0 > usbus1: 480Mbps High Speed USB v2.0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > ahci0: Intel hocus pocus > ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 > 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps) > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > ugen1.3: <DELL> at usbus1 > ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on > usbus1 > kbd2 at ukbd0 > ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018" > ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES > capacity=30533.83MB > ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen > ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584" > ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282" > ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.5: No device detected > pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18 > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > cpu0: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef Cpu0Cst 00003001 INTL > 20051117) > cpu_cst0: <ACPI CPU C-State> on cpu0 > cpu_pst0: <ACPI CPU P-State> on cpu0 > clockmod0: <CPU clock modulation> on cpu0 > perfbias0: <CPU perf-energy bias> on cpu0 > coretemp0: <CPU On-Die Thermal Sensors> on cpu0 > cpu1: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef ApIst 00003000 INTL > 20051117) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef ApCst 00003000 INTL > 20051117) > cpu_cst1: <ACPI CPU C-State> on cpu1 > cpu_pst1: <ACPI CPU P-State> on cpu1 > clockmod1: <CPU clock modulation> on cpu1 > perfbias1: <CPU perf-energy bias> on cpu1 > coretemp1: <CPU On-Die Thermal Sensors> on cpu1 > ACPI: Enabled 6 GPEs in block 00 to 3F > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x500 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > hpt27xx: no controller detected. > CAM: Configuring 4 busses > CAM: finished configuring all busses > da0 at ahci0 bus 0 target 0 lun 0 > da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device > da0: Serial Number B620550018 > da0: 600.000MB/s transfers > da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C) > da0: supports TRIM > da1 at ahci0 bus 2 target 0 lun 0 > da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da1: Serial Number WD-WCAWZ2969584 > da1: 300.000MB/s transfers > da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da2 at ahci0 bus 4 target 0 lun 0 > da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da2: Serial Number WD-WCAWZ2111282 > da2: 300.000MB/s transfers > da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da1 part 0: unavailable, bad start or ending lba > da2 part 0: unavailable, bad start or ending lba > no B_DEVMAGIC (bootdev=0) > Mounting root from hammer:serno/B620550018.s1d > HAMMER(ROOT) recovery check seqno=0899d83f > HAMMER(ROOT) recovery range 3000000014705cc0-3000000014705cc0 > HAMMER(ROOT) recovery nexto 3000000014705cc0 endseqno=0899d840 > HAMMER(ROOT) mounted clean, no recovery needed > DMA space used: 10428k, remaining available: 131072k > Mounting devfs > HAMMER(DATA) recovery check seqno=2fa3a14d > HAMMER(DATA) recovery range 3000000036618778-3000000036618778 > HAMMER(DATA) recovery nexto 3000000036618778 endseqno=2fa3a14e > HAMMER(DATA) mounted clean, no recovery needed > HAMMER(BACKUP) recovery check seqno=040b37a1 > HAMMER(BACKUP) recovery range 300000003238b358-300000003238b358 > HAMMER(BACKUP) recovery nexto 300000003238b358 endseqno=040b37a2 > HAMMER(BACKUP) mounted clean, no recovery needed > swap low/high-water marks set to 67683/101525 > pflog0: promiscuous mode enabled > boot() called on cpu#1 > Switching to cpu #0 for shutdown > Waiting (max 60 seconds) for system thread swapcached to stop...stopped > Waiting (max 60 seconds) for system thread vnlru to stop...stopped > Waiting (max 60 seconds) for system thread consttyd to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped > > syncing disks... > done > vflush: Warning, cannot destroy busy device vnode > unmount of filesystem mounted from devfs failed (BUSY) > unmount(0xffffff81d6e23cc0): Forced unmount: 0 namecache references still > present > unmount(0xffffff81d6e23cc0): Forced unmount: 1 mount refs still present > Copyright (c) 2003-2017 The DragonFly Project. > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017 > [email protected]:/usr/obj/usr/src/sys/X86_64_GENERIC > i8254 clock: 1193296 Hz > TSC invariant clock: 1795934260 Hz > CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB> > Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM> > MONITOR/MWAIT Features=0x3<CST,INTBRK> > real memory = 8477464576 (8084 MB) > avail memory = 7884136448 (7518 MB) > lapic: divisor index 0, frequency 49886864 Hz > srat_probe: can't locate SRAT > Initialize MI interrupts > TSC testing MP synchronization ... > cpu1: TSC is not MP synchronized @0 > TSC is not MP synchronized > VMM: available, disabled by default > wdog: In-kernel automatic watchdog reset enabled > kbd1 at kbdmux0 > md0: Malloc disk > interrupt uses mplock: swi_taskq > ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA) > ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I 01072009 AMI > 00010013) > ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I 00000028 INTL > 20051117) > ACPI: FACS 0x00000000DABB7080 000040 > ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I 01072009 MSFT > 00000097) > ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I 01072009 AMI. > 00000005) > ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL > 20091112) > ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef Cpu0Ist 00003000 INTL > 20051117) > ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef CpuPm 00003000 INTL > 20051117) > cryptosoft0: <software crypto> on motherboard > aesni0: No AESNI support. > padlock0: No ACE support. > rdrand0: No RdRand support. > acpi0: <ALASKA A M I> on motherboard > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: 4 ACPI AML tables successfully acquired and loaded > ACPI FADT: SCI testing interrupt mode ... > ACPI FADT: SCI select level/high > acpi0: Power Button (fixed) > acpi_timer0 on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > acpi_hpet0: frequency 14318180 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 16 at device 2.0 on pci0 > vgapci0: Boot video device > pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 16 > ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 16 at device 26.0 on pci0 > usbus0: EHCI version 1.0 > usbus0 on ehci0 > pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 22 > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > usbus0: 480Mbps High Speed USB v2.0 > pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem > 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 18 at device 0.0 on pci2 > re0: MAC version 0x2c900000, MACFG 39, support MSI > re0: bus speed 125MHz > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > re0: MAC address: b8:ae:ed:3c:ce:35 > ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 23 at device 29.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > ahci0: <AHCI-PCI-SATA> port > 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem > 0xf7d06000-0xf7d067ff irq 16 at device 31.2 on pci0 > usbus1: 480Mbps High Speed USB v2.0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > ahci0: Intel hocus pocus > ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 > 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps) > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > ugen1.3: <DELL> at usbus1 > ukbd0: <DELL Dell USB Entry Keyboard, class 0/0, rev 1.10/1.78, addr 3> on > usbus1 > kbd2 at ukbd0 > ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018" > ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES > capacity=30533.83MB > ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen > ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584" > ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282" > ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.5: No device detected > pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 18 > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > cpu0: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef Cpu0Cst 00003001 INTL > 20051117) > cpu_cst0: <ACPI CPU C-State> on cpu0 > cpu_pst0: <ACPI CPU P-State> on cpu0 > clockmod0: <CPU clock modulation> on cpu0 > perfbias0: <CPU perf-energy bias> on cpu0 > coretemp0: <CPU On-Die Thermal Sensors> on cpu0 > cpu1: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81DBEEF140 000303 (v01 PmRef ApIst 00003000 INTL > 20051117) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef ApCst 00003000 INTL > 20051117) > cpu_cst1: <ACPI CPU C-State> on cpu1 > cpu_pst1: <ACPI CPU P-State> on cpu1 > clockmod1: <CPU clock modulation> on cpu1 > perfbias1: <CPU perf-energy bias> on cpu1 > coretemp1: <CPU On-Die Thermal Sensors> on cpu1 > ACPI: Enabled 6 GPEs in block 00 to 3F > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x500 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > hpt27xx: no controller detected. > CAM: Configuring 4 busses > CAM: finished configuring all busses > da0 at ahci0 bus 0 target 0 lun 0 > da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device > da0: Serial Number B620550018 > da0: 600.000MB/s transfers > da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C) > da0: supports TRIM > da1 at ahci0 bus 2 target 0 lun 0 > da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da1: Serial Number WD-WCAWZ2969584 > da1: 300.000MB/s transfers > da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da2 at ahci0 bus 4 target 0 lun 0 > da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da2: Serial Number WD-WCAWZ2111282 > da2: 300.000MB/s transfers > da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da1 part 0: unavailable, bad start or ending lba > da2 part 0: unavailable, bad start or ending lba > no B_DEVMAGIC (bootdev=0) > Mounting root from hammer:serno/B620550018.s1d > HAMMER(ROOT) recovery check seqno=08a3bb68 > HAMMER(ROOT) recovery range 3000000006f2d038-3000000006f2d038 > HAMMER(ROOT) recovery nexto 3000000006f2d038 endseqno=08a3bb69 > HAMMER(ROOT) mounted clean, no recovery needed > DMA space used: 10428k, remaining available: 131072k > Mounting devfs > HAMMER(DATA) recovery check seqno=2fc8308a > HAMMER(DATA) recovery range 300000002c2f7648-300000002c2f7648 > HAMMER(DATA) recovery nexto 300000002c2f7648 endseqno=2fc8308b > HAMMER(DATA) mounted clean, no recovery needed > HAMMER(BACKUP) recovery check seqno=040ce7dc > HAMMER(BACKUP) recovery range 300000003552fb48-300000003552fb48 > HAMMER(BACKUP) recovery nexto 300000003552fb48 endseqno=040ce7dd > HAMMER(BACKUP) mounted clean, no recovery needed > swap low/high-water marks set to 67683/101525 > pflog0: promiscuous mode enabled > ugen1.3: <DELL> at usbus1 (disconnected) > ukbd0: at uhub3, port 2, addr 3 (disconnected) > ukbd0: detached > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 11963/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 10924/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 19755/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 14432/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 15229/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 5868/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 15568/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > intr 16 on cpu0 at 1966/20000 hz, livelock removed > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! > boot() called on cpu#1 > Switching to cpu #0 for shutdown > Waiting (max 60 seconds) for system thread swapcached to stop...stopped > Waiting (max 60 seconds) for system thread vnlru to stop...stopped > Waiting (max 60 seconds) for system thread consttyd to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon to stop...stopped > Waiting (max 60 seconds) for system thread bufdaemon_hw to stop...stopped > > syncing disks... > done > vflush: Warning, cannot destroy busy device vnode > unmount of filesystem mounted from devfs failed (BUSY) > unmount(0xffffff81d6e23cc0): Forced unmount: 0 namecache references still > present > unmount(0xffffff81d6e23cc0): Forced unmount: 1 mount refs still present > vflush: Warning, cannot destroy busy device vnode > unmount of filesystem mounted from devfs failed (BUSY) > Uptime: 1d20h17m17s > intr 16 on cpu0 at 15420/20000 hz, livelock removed > Copyright (c) 2003-2017 The DragonFly Project. > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > DragonFly v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017 > [email protected]:/usr/obj/usr/src/sys/X86_64_GENERIC > i8254 clock: 1193297 Hz > TSC invariant clock: 1795934560 Hz > CPU: Intel(R) Celeron(R) CPU 1037U @ 1.80GHz (1795.93-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > Structured Extended Features=0x281<GSFSBASE,SMEP,ENHMOVSB> > Thermal and PM Features=0x75<SENSOR,ARAT,PLN,ECMD,PTM> > MONITOR/MWAIT Features=0x3<CST,INTBRK> > real memory = 8477464576 (8084 MB) > avail memory = 7884136448 (7518 MB) > lapic: divisor index 0, frequency 49886789 Hz > srat_probe: can't locate SRAT > Initialize MI interrupts > TSC testing MP synchronization ... > cpu1: TSC is not MP synchronized @0 > TSC is not MP synchronized > VMM: available, disabled by default > wdog: In-kernel automatic watchdog reset enabled > kbd1 at kbdmux0 > md0: Malloc disk > interrupt uses mplock: swi_taskq > ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA) > ACPI: XSDT 0x00000000DA781070 000064 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FACP 0x00000000DA78C908 00010C (v05 ALASKA A M I 01072009 AMI > 00010013) > ACPI: DSDT 0x00000000DA781168 00B79B (v02 ALASKA A M I 00000028 INTL > 20051117) > ACPI: FACS 0x00000000DABB7080 000040 > ACPI: APIC 0x00000000DA78CA18 000062 (v03 ALASKA A M I 01072009 AMI > 00010013) > ACPI: FPDT 0x00000000DA78CA80 000044 (v01 ALASKA A M I 01072009 AMI > 00010013) > ACPI: MCFG 0x00000000DA78CAC8 00003C (v01 ALASKA A M I 01072009 MSFT > 00000097) > ACPI: HPET 0x00000000DA78CB08 000038 (v01 ALASKA A M I 01072009 AMI. > 00000005) > ACPI: SSDT 0x00000000DA78CB40 000315 (v01 SataRe SataTabl 00001000 INTL > 20091112) > ACPI: SSDT 0x00000000DA78CE58 000860 (v01 PmRef Cpu0Ist 00003000 INTL > 20051117) > ACPI: SSDT 0x00000000DA78D6B8 000B22 (v01 PmRef CpuPm 00003000 INTL > 20051117) > cryptosoft0: <software crypto> on motherboard > aesni0: No AESNI support. > padlock0: No ACE support. > rdrand0: No RdRand support. > acpi0: <ALASKA A M I> on motherboard > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: 4 ACPI AML tables successfully acquired and loaded > ACPI FADT: SCI testing interrupt mode ... > ACPI FADT: SCI select level/low > acpi0: Power Button (fixed) > acpi_timer0 on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > acpi_hpet0: frequency 14318180 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xe0000000-0xefffffff,0xf7800000-0xf7bfffff irq 11 at device 2.0 on pci0 > vgapci0: Boot video device > pci0: <simple comms> (vendor 0x8086, dev 0x1e3a) at device 22.0 irq 11 > ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 11 at device 26.0 on pci0 > usbus0: EHCI version 1.0 > usbus0 on ehci0 > pci0: <multimedia, HDA> (vendor 0x8086, dev 0x1e20) at device 27.0 irq 11 > pcib1: <ACPI PCI-PCI bridge> irq 11 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > usbus0: 480Mbps High Speed USB v2.0 > pcib2: <ACPI PCI-PCI bridge> irq 10 at device 28.2 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re0: <RealTek 8111/8168 PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem > 0xf0000000-0xf0003fff,0xf7c00000-0xf7c00fff irq 10 at device 0.0 on pci2 > re0: MAC version 0x2c900000, MACFG 39, support MSI > re0: bus speed 125MHz > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > re0: MAC address: b8:ae:ed:3c:ce:35 > ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 11 at device 29.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > ahci0: <AHCI-PCI-SATA> port > 0xf060-0xf07f,0xf080-0xf083,0xf090-0xf097,0xf0a0-0xf0a3,0xf0b0-0xf0b7 mem > 0xf7d06000-0xf7d067ff irq 11 at device 31.2 on pci0 > usbus1: 480Mbps High Speed USB v2.0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > ahci0: Intel hocus pocus > ahci0: AHCI 1.3 cap 0xc730ff43<S64A,NCQ,SALP,SAL,SCLO,PMD,SSC,PSC,EMS> cap2 > 0x4<APST>, 4 ports, 32 tags/port, gen 3 (6Gbps) > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > ahci0.0: Found SSD "TS32GMTS400 20140516" serial="B620550018" > ahci0.0: tags=32/32 satacap=830e satacap2=0086 satafea=054c NCQ=YES > capacity=30533.83MB > ahci0.0: f85=7469 f86=b401 f87=4063 WC=enabled RA=enabled SEC=frozen > ahci0.2: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2969584" > ahci0.2: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.2: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.4: Found DISK "WDC WD30EZRX-00MMMB0 80.00A80" serial="WD-WCAWZ2111282" > ahci0.4: tags=32/32 satacap=170e satacap2=0004 satafea=0044 NCQ=YES > capacity=2861588.46MB > ahci0.4: f85=7469 f86=bc41 f87=4123 WC=enabled RA=enabled SEC=frozen > ahci0.5: No device detected > pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x1e22) at device 31.3 irq 10 > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > cpu0: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81D7025200 00083B (v01 PmRef Cpu0Cst 00003001 INTL > 20051117) > cpu_cst0: <ACPI CPU C-State> on cpu0 > cpu_pst0: <ACPI CPU P-State> on cpu0 > clockmod0: <CPU clock modulation> on cpu0 > perfbias0: <CPU perf-energy bias> on cpu0 > coretemp0: <CPU On-Die Thermal Sensors> on cpu0 > cpu1: <ACPI CPU> on acpi0 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF81DBE46F40 000303 (v01 PmRef ApIst 00003000 INTL > 20051117) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFFF805BBF7F40 000119 (v01 PmRef ApCst 00003000 INTL > 20051117) > cpu_cst1: <ACPI CPU C-State> on cpu1 > cpu_pst1: <ACPI CPU P-State> on cpu1 > clockmod1: <CPU clock modulation> on cpu1 > perfbias1: <CPU perf-energy bias> on cpu1 > coretemp1: <CPU On-Die Thermal Sensors> on cpu1 > ACPI: Enabled 6 GPEs in block 00 to 3F > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x500 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > hpt27xx: no controller detected. > CAM: Configuring 4 busses > CAM: finished configuring all busses > da0 at ahci0 bus 0 target 0 lun 0 > da0: <SATA TS32GMTS400 2014> Fixed Direct Access SCSI-4 device > da0: Serial Number B620550018 > da0: 600.000MB/s transfers > da0: 30533MB (62533296 512 byte sectors: 255H 63S/T 3892C) > da0: supports TRIM > da1 at ahci0 bus 2 target 0 lun 0 > da1: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da1: Serial Number WD-WCAWZ2969584 > da1: 300.000MB/s transfers > da1: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da2 at ahci0 bus 4 target 0 lun 0 > da2: <SATA WDC WD30EZRX-00M 80.0> Fixed Direct Access SCSI-4 device > da2: Serial Number WD-WCAWZ2111282 > da2: 300.000MB/s transfers > da2: 2861588MB (5860533168 512 byte sectors: 255H 63S/T 364801C) > da1 part 0: unavailable, bad start or ending lba > da2 part 0: unavailable, bad start or ending lba > no B_DEVMAGIC (bootdev=0) > Mounting root from hammer:serno/B620550018.s1d > HAMMER(ROOT) recovery check seqno=08b640b2 > HAMMER(ROOT) recovery range 3000000009728c38-3000000009728c38 > HAMMER(ROOT) recovery nexto 3000000009728c38 endseqno=08b640b3 > HAMMER(ROOT) mounted clean, no recovery needed > DMA space used: 10080k, remaining available: 131072k > Mounting devfs > HAMMER(DATA) recovery check seqno=30140895 > HAMMER(DATA) recovery range 3000000025aa8ab8-3000000025aa8ab8 > HAMMER(DATA) recovery nexto 3000000025aa8ab8 endseqno=30140896 > HAMMER(DATA) mounted clean, no recovery needed > HAMMER(BACKUP) recovery check seqno=0415fb69 > HAMMER(BACKUP) recovery range 3000000006059498-3000000006059498 > HAMMER(BACKUP) recovery nexto 3000000006059498 endseqno=0415fb6a > HAMMER(BACKUP) mounted clean, no recovery needed > swap low/high-water marks set to 67683/101525 > pflog0: promiscuous mode enabled > > > >> >> On Thu, Apr 20, 2017 at 11:10 AM, Predrag Punosevac >> <[email protected]> wrote: >> > Matthew Dillon wrote: >> > >> >> Your BIOS appears to be trying to emulate an ATA controller. There is >> >> no AHCI attachment. Go into setup and see if you can tell your BIOS to >> >> enable AHCI instead of ATA. >> >> >> >> -Matt >> > >> > Almost a year later even after adjusting BIOS settings (SATA controller >> > was trying to emulate ATA controller so I switched to AHCI) I kept >> > seeing >> > >> > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! >> > intr 16 on cpu0 at 11963/20000 hz, livelock removed >> > >> > even on the >> > >> > dfly# uname -a DragonFly dfly.bagdala2.net 4.8-RELEASE DragonFly >> > v4.8.0.1.g86163-RELEASE #4: Tue Mar 28 07:56:27 EST 2017 >> > [email protected]:/usr/obj/usr/src/sys/X86_64_GENERIC x86_64 >> > >> > Then I stumbled recently on this post >> > >> > http://yrabbit.freeshell.org/en/2012/03/04/dragonfly-bsd-under-qemu.html >> > >> > and sure enough >> > >> > echo 'hw.ioapic_enable=0' >> /boot/loader.conf.local reboot >> > >> > made >> > >> > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! >> > intr 16 on cpu0 at 11963/20000 hz, livelock removed >> > >> > disapear from dmesg. Unfortunatelly I don't know enough about Advanced >> > Programmable Interrupt Controller >> > >> > https://en.wikipedia.org/wiki/Advanced_Programmable_Interrupt_Controller >> > >> > so I am not sure if the above is just bandage for an actual bug which >> > looks like it should have being fixed >> > >> > http://lists.dragonflybsd.org/pipermail/bugs/2012-March/244444.html >> > >> > >> > Thanks, >> > Predrag >> > >> > >> > >> > >> > >> >> >> >> On Sat, Apr 16, 2016 at 4:10 PM, Predrag Punosevac >> >> <[email protected]> >> >> wrote: >> >> >> >> > Sepherosa Ziehau wrote: >> >> > >> >> > > On Tue, Apr 5, 2016 at 11:09 AM, Predrag Punosevac >> >> > > <[email protected]> wrote: >> >> > > > Sepherosa Ziehau <[email protected]> wrote: >> >> > > > >> >> > > >> Please post the output of 'vmstat -iv' >> >> > > > >> >> > > > dfly# vmstat -iv >> >> > > > interrupt total rate >> >> > > > irq4 0: sio0 0 0 >> >> > > > irq9 0: acpi0 0 0 >> >> > > > irq16 0: ehci0/atapci0/atapci1 61925216594 35565 >> >> > > >> >> > > >> >> > > I'd suspect its EHCI, do you have anything uses USB? If not, >> >> disable >> >> > > the EHCI from BIOS and see whether it works for you or not. >> >> > >> >> > I disabled completely USB from BIOS. The error is still there here is >> >> the >> >> > new output from vmstat >> >> > >> >> > intr 16 on cpu0 at 40001/40000 hz, livelocked limit engaged! >> >> > dfly# vmstat -iv >> >> > interrupt total rate >> >> > irq4 0: sio0 0 0 >> >> > irq9 0: acpi0 0 0 >> >> > irq16 0: atapci0/atapci1 7508403 35085 >> >> > irq18 0: re0 265 1 >> >> > irq192 0: swi_siopoll 0 0 >> >> > irq196 0: swi_vm 0 0 >> >> > irq1 1: atkbd0 7 0 >> >> > irq3 1: sio1 0 0 >> >> > irq195 1: swi_cambio 38 0 >> >> > irq197 1: swi_mp_taskq/swi_taskq 1738 8 >> >> > Total 7510451 35095 >> >> > >> >> > >> >> > Any idea? Looks like DF has a problem with HDD SATA controller. >> >> > >> >> > Predrag >> >> > >> >> > >> >> > >> >> >> >> -- >> Tomorrow Will Never Die -- Tomorrow Will Never Die
