Hello all,
My name is Tuan H. Nguyen. I am working for Navy research lab at San
Diego CA.
I have two IPV6 linux systems (kernel 2.4.2) with 3 network interfaces:
eth0, eth1, and hdlc0(cyclades pc300 sync serial card) . Both system
are identical.
But there are only the ethernet (eth0 & eth1)working OK with IPv4/ipv6
(I can ping6 each other), except the serial (hdlc0) is not working with
IPV6(ipv4 OK). Does anyone know to configure the hdlc0 interface(PPP)
on linux to make serial (PPP) work with ipv6? Is it the ipv6 over ppp
implemented yet? The following is my system configuration:
[root@821dhcp092 thtran]# /sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:60:97:4F:AB:36
inet addr:128.49.140.92 Bcast:128.49.140.255
Mask:255.255.255.0
inet6 addr: fe80::260:97ff:fe4f:ab36/10 Scope:Link
inet6 addr: 4080::260:97ff:fe4f:ab36/10 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18375 errors:0 dropped:0 overruns:0 frame:0
TX packets:1712 errors:0 dropped:0 overruns:0 carrier:3
collisions:86 txqueuelen:100
Interrupt:9 Base address:0xd400
eth1 Link encap:Ethernet HWaddr 00:E0:18:1E:0D:B3
inet addr:128.49.214.200 Bcast:128.49.214.255
Mask:255.255.255.0
inet6 addr: 5080::2e0:18ff:fe1e:db3/10 Scopte:Global
inet6 addr: fe80::2e0:18ff:fe1e:db3/10 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:9
hdlc0 Link encap:Point-to-Point Protocol
inet addr:205.53.10.2 P-t-P:205.53.10.1 Mask:255.255.255.252
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:648 errors:0 dropped:0 overruns:0 frame:0
TX packets:669 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
Interrupt:9 Memory:eb000000-eb03ffff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:3856 Metric:1
RX packets:90 errors:0 dropped:0 overruns:0 frame:0
TX packets:90 errors:0 Hello all,
I have tried to use ifconfig to add ipv6 addresses for hdlc0 such as:
#ifconfig hdlc0 add 7080::260:97ff:fe4f:ab11/10
#ifconfig hdlc0 add fe80::260:97ff:fe4f:ab11/10
The hdlc0 looked like:
hdlc0 Link encap:Point-to-Point Protocol
inet addr:205.53.10.2 P-t-P:205.53.10.1 Mask:255.255.255.252
inet6 addr: 7080::260:97ff:fe4f:ab11/10 Scope:Global
inet6 addr: fe80::260:97ff:fe4f:ab11/10 Scope:Link
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:648 errors:0 dropped:0 overruns:0 frame:0
TX packets:669 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
Interrupt:9 Memory:eb000000-eb03ffff
But it does not work either.
I need your help.
Thanks.
/Tuan Nguyen
---------------------------------------------------------------------
The IPv6 Users Mailing List
Unsubscribe by sending "unsubscribe users" to [EMAIL PROTECTED]
