Hello Christian
On 10/10/23 11:24, Christian Helmuth wrote:
Hello Sculpt users,
we entered the testing phase for the upcoming Sculpt 23.10. Before the
final release, we like to invite early adopters to give our release
candidate a try and report back experiences (or issues) with their use
cases.
The current candidate is RC4 and can be retrieved via the "System ->
Update" dialog in entry https://depot.genode.org/chelmuth of your
current Sculpt installation. Alternatively, you may download the image
from the following URL.
https://depot.genode.org/chelmuth/image/sculpt-pc-2023-10-10.img.xz
I did give the image a quick try on my i7 11700 desktop.
When I try to activate the wired network I get the following output:
[init -> nic_drv] time-clocksource: dde_counter: mask: 0xffffffffffffff
max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
[init -> nic_drv] time-clocksource: jiffies: mask: 0xffffffff
max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[init -> nic_drv] time-clocksource: Switched to clocksource dde_counter
[init -> nic_drv] e1000-e1000_main: Intel(R) PRO/1000 Network Driver
[init -> nic_drv] e1000-e1000_main: Copyright (c) 1999-2006 Intel
Corporation.
[init -> nic_drv] e1000e-netdev: Intel(R) PRO/1000 Network Driver
[init -> nic_drv] e1000e-netdev: Copyright(c) 1999 - 2015 Intel Corporation.
[init -> nic_drv] realtek-r8169_main 07:00.0 eth0: RTL8168e/8111e,
08:be:ac:22:6c:52, XID 2c2, IRQ 21
[init -> nic_drv] realtek-r8169_main 07:00.0 eth0: jumbo features
[frames: 9194 bytes, tx checksumming: ko]
[init -> nic_drv] sched_clock: Marking stable (135525000,
255074000)->(417182000, -26583000)
[init -> nic_drv] realtek-r8169_main 07:00.0: Unable to load firmware
rtl_nic/rtl8168e-2.fw (-1)
[init -> nic_drv] RTL8211DN Gigabit Ethernet r8169-0-0:00: attached PHY
driver (mii_bus:phy_addr=r8169-0-0:00, irq=MAC)
[init -> nic_drv] realtek-r8169_main 07:00.0 eth0: No native access to
PCI extended config space, falling back to CSI
[init -> nic_drv] Error: Function pcie_capability_clear_and_set_word not
implemented yet!
[init -> nic_drv] Backtrace follows:
Error: illegal READ at address 0xfffffffffffa77b8 by pager_object:
pd='init -> nic_drv' thread='ep' ip=0x10a8330
The card is plugged to one of the PCIe ports, as the onboard controller
is an Intel IGC 2.5GB adapter.
Linux reports (`lspci -vv`):
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
Subsystem: Realtek Semiconductor Co., Ltd. Device 0123
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at 6010904000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at 6010900000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
dmesg:
[ 1.535318] r8169 0000:07:00.0: enabling device (0000 -> 0003)
[ 1.535415] r8169 0000:07:00.0: can't disable ASPM; OS doesn't have
ASPM control
[ 1.537162] r8169 0000:07:00.0 eth0: RTL8168e/8111e,
08:be:ac:22:6c:52, XID 2c2, IRQ 153
[ 1.537165] r8169 0000:07:00.0 eth0: jumbo features [frames: 9194
bytes, tx checksumming: ko]
[ 4.922396] r8169 0000:07:00.0 enp7s0: renamed from eth0
[ 14.174715] RTL8211DN Gigabit Ethernet r8169-0-700:00: attached PHY
driver (mii_bus:phy_addr=r8169-0-700:00, irq=MAC)
[ 14.461989] r8169 0000:07:00.0 enp7s0: Link is Down
[ 17.257971] r8169 0000:07:00.0 enp7s0: Link is Up - 1Gbps/Full - flow
control rx/tx
I will check on the week end if the card works with an older sculpt
version, as I never have used it with sculpt. My main use case up until
now was to do iPXE-boot with it while testing the driver for the Intel
IGC nic.
Regards,
Pirmin
_______________________________________________
Genode users mailing list
[email protected]
https://lists.genode.org/listinfo/users
