The fw version 2.3.0 is too old. I recommend you to upgrade to the
latest version (2.6.0) from
Mellanox website
http://www.mellanox.com/content/pages.php?pg=firmware_table_ConnectXIB
Thanks,
Pasha
Jeff Layton wrote:
Oops. I ran it on the head node and not the compute node. Here is the
output from a compute node:
hca_id: mlx4_0
fw_ver: 2.3.000
node_guid: 0018:8b90:97fe:1b6d
sys_image_guid: 0018:8b90:97fe:1b70
vendor_id: 0x02c9
vendor_part_id: 25418
hw_ver: 0xA0
board_id: DEL08C0000001
phys_port_cnt: 2
max_mr_size: 0xffffffffffffffff
page_size_cap: 0xfffff000
max_qp: 131008
max_qp_wr: 16351
device_cap_flags: 0x001c1c66
max_sge: 32
max_sge_rd: 0
max_cq: 65408
max_cqe: 4194303
max_mr: 131056
max_pd: 32764
max_qp_rd_atom: 16
max_ee_rd_atom: 0
max_res_rd_atom: 2096128
max_qp_init_rd_atom: 128
max_ee_init_rd_atom: 0
atomic_cap: ATOMIC_HCA (1)
max_ee: 0
max_rdd: 0
max_mw: 0
max_raw_ipv6_qp: 0
max_raw_ethy_qp: 0
max_mcast_grp: 8192
max_mcast_qp_attach: 56
max_total_mcast_qp_attach: 458752
max_ah: 0
max_fmr: 0
max_srq: 65472
max_srq_wr: 16383
max_srq_sge: 31
max_pkeys: 128
local_ca_ack_delay: 15
port: 1
state: PORT_ACTIVE (4)
max_mtu: 2048 (4)
active_mtu: 2048 (4)
sm_lid: 41
port_lid: 70
port_lmc: 0x00
max_msg_sz: 0x40000000
port_cap_flags: 0x02510868
max_vl_num: 8 (4)
bad_pkey_cntr: 0x0
qkey_viol_cntr: 0x0
sm_sl: 0
pkey_tbl_len: 128
gid_tbl_len: 128
subnet_timeout: 18
init_type_reply: 0
active_width: 4X (2)
active_speed: 5.0 Gbps (2)
phys_state: LINK_UP (5)
GID[ 0]:
fe80:0000:0000:0000:0018:8b90:97fe:1b6e
port: 2
state: PORT_DOWN (1)
max_mtu: 2048 (4)
active_mtu: 2048 (4)
sm_lid: 0
port_lid: 0
port_lmc: 0x00
max_msg_sz: 0x40000000
port_cap_flags: 0x02510868
max_vl_num: 8 (4)
bad_pkey_cntr: 0x0
qkey_viol_cntr: 0x0
sm_sl: 0
pkey_tbl_len: 128
gid_tbl_len: 128
subnet_timeout: 0
init_type_reply: 0
active_width: 4X (2)
active_speed: 2.5 Gbps (1)
phys_state: POLLING (2)
GID[ 0]:
fe80:0000:0000:0000:0018:8b90:97fe:1b6f
Do you have the same HCA adapter type on all of your machines ?
In the error log I see mlx4 error message , and mlx4 is connectX driver,
but ibv_devinfo show some older hca.
Jeff,
Can you please provide more information about you HCA type
(ibv_devinfo -v).
Do you see this error immediate during startup, or you get it
during your run ?
Thanks,
Pasha
Jeff Layton wrote:
Evening everyone,
I'm running a CFD code on IB and I've encountered an error I'm not
sure about and I'm looking for some guidance on where to start
looking. Here's the error:
mlx4: local QP operation err (QPN 260092, WQE index 9a9e0000,
vendor syndrome 6f, opcode = 5e)
[0,1,6][btl_openib_component.c:1392:btl_openib_component_progress]
from compute-2-0.local to: compute-2-0.local erro
r polling HP CQ with status LOCAL QP OPERATION ERROR status number
2 for wr_id 37742320 opcode 0
mpirun noticed that job rank 0 with PID 21220 on node
compute-2-0.local exited on signal 15 (Terminated).
78 additional processes aborted (not shown)
This is openmpi-1.2.9rc2 (sorry - need to upgrade to 1.3.0). The
code works correctly for smaller cases, but when I run larger
cases I get this error.
I'm heading to bed but I'll check email tomorrow (so to sleep and
run but it's been a long day).
TIA!
Jeff
------------------------------------------------------------------------
_______________________________________________
users mailing list
us...@open-mpi.org
http://www.open-mpi.org/mailman/listinfo.cgi/users
_______________________________________________
users mailing list
us...@open-mpi.org
http://www.open-mpi.org/mailman/listinfo.cgi/users
