Hi,
I try to bind both the memory and processes on our compute cluster nodes
but only the processes binding works. How can I also specify to allocate
the memory on the same numa node than where the process is bind? I tried
with the option "--mca hwloc_base_mem_alloc_policy local_only" without
any luck.
I tested the memory biding with a small c++ program that allocates an
array of 1.8GB of memory and then touches that memory. When I run it
with this command line
mpirun -np 8 --mca mpi_paffinity_alone 1 --mca
hwloc_base_mem_alloc_policy local_only ./numa_test
and look at the binding with hwloc-ps or lstopo I get the right
processes binding. However, the /proc/process_id/num_maps doesn't
indicate any memory binding other than the default one and some memory
pages are allocated on both numa node memory.
------cat /proc/process_id/numa_maps ------
...
7fe12d778000 default anon=267996 dirty=267996 active=254510 N0=74502
N1=193494
...
-----
If I run the program again with an explicit hwloc-bind command like this
mpirun -np 4 hwloc-bind --cpubind node:0 --membind node:0 --strict
./numa_test : -np 4 hwloc-bind --cpubind node:1 --membind node:1
--strict ./numa_test
now I get the expected results (with the bind:0 or bind:1),
------cat /proc/process_id/numa_maps ------
...
7fb54cbe4000 bind:0 anon=95747 dirty=95747 active=70221 N0=95747
...
or
...
7fe6e19e3000 bind:1 anon=468751 dirty=468751 N1=468751
...
-----
The comment for the hwloc_base_mem_alloc_policy parameter says:
-------
> MCA hwloc: parameter "hwloc_base_mem_alloc_policy" (current value:
> <none>, data source: default value)
> Policy that determines how general memory
> allocations are bound after MPI_INIT. A value of "none" means that no
> memory policy is applied. A value of "local_only" means that all
> memory allocations will be restricted to the local NUMA node where
> each process is placed. Note that operating system paging policies
> are unaffected by this setting. For example, if "local_only" is used
> and local NUMA node memory is exhausted, a new memory allocation may
> cause paging.
------
I though that it's what I want but it doesn't have any effect.
I compiled Open MPI with these options. I disabled the "first_use"
memory affinity to be sure that openmpi uses the "hwloc" policy (Open
MPI shows the same behavior with or without the "first_use" policy anyway).
-----------------------
node-01%head config.log
This file contains any messages produced by compilers while
running configure, to aid debugging if configure makes a mistake.
It was created by Open MPI configure 1.6, which was
generated by GNU Autoconf 2.68. Invocation command line was
$ ./configure --prefix=/home/apps/Logiciels/MPI/intel/openmpi/1.6
--with-tm=/opt/torque --with-openib
--enable-mca-no-build=maffinity-first_use CC=icc CXX=icpc F77=ifort FC=ifort
------------------------
ompi_info -a
Package: Open MPI bib@udem Distribution
Open MPI: 1.6
Open MPI SVN revision: r26429
Open MPI release date: May 10, 2012
Open RTE: 1.6
Open RTE SVN revision: r26429
Open RTE release date: May 10, 2012
OPAL: 1.6
OPAL SVN revision: r26429
OPAL release date: May 10, 2012
MPI API: 2.1
Ident string: 1.6
MCA backtrace: execinfo (MCA v2.0, API v2.0, Component v1.6)
MCA memory: linux (MCA v2.0, API v2.0, Component v1.6)
MCA paffinity: hwloc (MCA v2.0, API v2.0, Component v1.6)
MCA carto: auto_detect (MCA v2.0, API v2.0, Component v1.6)
MCA carto: file (MCA v2.0, API v2.0, Component v1.6)
MCA shmem: mmap (MCA v2.0, API v2.0, Component v1.6)
MCA shmem: posix (MCA v2.0, API v2.0, Component v1.6)
MCA shmem: sysv (MCA v2.0, API v2.0, Component v1.6)
MCA maffinity: hwloc (MCA v2.0, API v2.0, Component v1.6)
MCA timer: linux (MCA v2.0, API v2.0, Component v1.6)
MCA installdirs: env (MCA v2.0, API v2.0, Component v1.6)
MCA installdirs: config (MCA v2.0, API v2.0, Component v1.6)
MCA sysinfo: linux (MCA v2.0, API v2.0, Component v1.6)
MCA hwloc: hwloc132 (MCA v2.0, API v2.0, Component v1.6)
MCA dpm: orte (MCA v2.0, API v2.0, Component v1.6)
MCA pubsub: orte (MCA v2.0, API v2.0, Component v1.6)
MCA allocator: basic (MCA v2.0, API v2.0, Component v1.6)
MCA allocator: bucket (MCA v2.0, API v2.0, Component v1.6)
MCA coll: basic (MCA v2.0, API v2.0, Component v1.6)
MCA coll: hierarch (MCA v2.0, API v2.0, Component v1.6)
MCA coll: inter (MCA v2.0, API v2.0, Component v1.6)
MCA coll: self (MCA v2.0, API v2.0, Component v1.6)
MCA coll: sm (MCA v2.0, API v2.0, Component v1.6)
MCA coll: sync (MCA v2.0, API v2.0, Component v1.6)
MCA coll: tuned (MCA v2.0, API v2.0, Component v1.6)
MCA io: romio (MCA v2.0, API v2.0, Component v1.6)
MCA mpool: fake (MCA v2.0, API v2.0, Component v1.6)
MCA mpool: rdma (MCA v2.0, API v2.0, Component v1.6)
MCA mpool: sm (MCA v2.0, API v2.0, Component v1.6)
MCA pml: bfo (MCA v2.0, API v2.0, Component v1.6)
MCA pml: csum (MCA v2.0, API v2.0, Component v1.6)
MCA pml: ob1 (MCA v2.0, API v2.0, Component v1.6)
MCA pml: v (MCA v2.0, API v2.0, Component v1.6)
MCA bml: r2 (MCA v2.0, API v2.0, Component v1.6)
MCA rcache: vma (MCA v2.0, API v2.0, Component v1.6)
MCA btl: ofud (MCA v2.0, API v2.0, Component v1.6)
MCA btl: openib (MCA v2.0, API v2.0, Component v1.6)
MCA btl: self (MCA v2.0, API v2.0, Component v1.6)
MCA btl: sm (MCA v2.0, API v2.0, Component v1.6)
MCA btl: tcp (MCA v2.0, API v2.0, Component v1.6)
MCA topo: unity (MCA v2.0, API v2.0, Component v1.6)
MCA osc: pt2pt (MCA v2.0, API v2.0, Component v1.6)
MCA osc: rdma (MCA v2.0, API v2.0, Component v1.6)
MCA iof: hnp (MCA v2.0, API v2.0, Component v1.6)
MCA iof: orted (MCA v2.0, API v2.0, Component v1.6)
MCA iof: tool (MCA v2.0, API v2.0, Component v1.6)
MCA oob: tcp (MCA v2.0, API v2.0, Component v1.6)
MCA odls: default (MCA v2.0, API v2.0, Component v1.6)
MCA ras: cm (MCA v2.0, API v2.0, Component v1.6)
MCA ras: loadleveler (MCA v2.0, API v2.0, Component v1.6)
MCA ras: slurm (MCA v2.0, API v2.0, Component v1.6)
MCA ras: tm (MCA v2.0, API v2.0, Component v1.6)
MCA rmaps: load_balance (MCA v2.0, API v2.0, Component v1.6)
MCA rmaps: rank_file (MCA v2.0, API v2.0, Component v1.6)
MCA rmaps: resilient (MCA v2.0, API v2.0, Component v1.6)
MCA rmaps: round_robin (MCA v2.0, API v2.0, Component v1.6)
MCA rmaps: seq (MCA v2.0, API v2.0, Component v1.6)
MCA rmaps: topo (MCA v2.0, API v2.0, Component v1.6)
MCA rml: oob (MCA v2.0, API v2.0, Component v1.6)
MCA routed: binomial (MCA v2.0, API v2.0, Component v1.6)
MCA routed: cm (MCA v2.0, API v2.0, Component v1.6)
MCA routed: direct (MCA v2.0, API v2.0, Component v1.6)
MCA routed: linear (MCA v2.0, API v2.0, Component v1.6)
MCA routed: radix (MCA v2.0, API v2.0, Component v1.6)
MCA routed: slave (MCA v2.0, API v2.0, Component v1.6)
MCA plm: rsh (MCA v2.0, API v2.0, Component v1.6)
MCA plm: slurm (MCA v2.0, API v2.0, Component v1.6)
MCA plm: tm (MCA v2.0, API v2.0, Component v1.6)
MCA filem: rsh (MCA v2.0, API v2.0, Component v1.6)
MCA errmgr: default (MCA v2.0, API v2.0, Component v1.6)
MCA ess: env (MCA v2.0, API v2.0, Component v1.6)
MCA ess: hnp (MCA v2.0, API v2.0, Component v1.6)
MCA ess: singleton (MCA v2.0, API v2.0, Component v1.6)
MCA ess: slave (MCA v2.0, API v2.0, Component v1.6)
MCA ess: slurm (MCA v2.0, API v2.0, Component v1.6)
MCA ess: slurmd (MCA v2.0, API v2.0, Component v1.6)
MCA ess: tm (MCA v2.0, API v2.0, Component v1.6)
MCA ess: tool (MCA v2.0, API v2.0, Component v1.6)
MCA grpcomm: bad (MCA v2.0, API v2.0, Component v1.6)
MCA grpcomm: basic (MCA v2.0, API v2.0, Component v1.6)
MCA grpcomm: hier (MCA v2.0, API v2.0, Component v1.6)
MCA notifier: command (MCA v2.0, API v1.0, Component v1.6)
MCA notifier: syslog (MCA v2.0, API v1.0, Component v1.6)
Prefix: /home/apps/Logiciels/MPI/intel/openmpi/1.6
Exec_prefix: /home/apps/Logiciels/MPI/intel/openmpi/1.6
Bindir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/bin
Sbindir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/sbin
Libdir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/lib
Incdir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/include
Mandir:
/home/apps/Logiciels/MPI/intel/openmpi/1.6/share/man
Pkglibdir:
/home/apps/Logiciels/MPI/intel/openmpi/1.6/lib/openmpi
Libexecdir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/libexec
Datarootdir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/share
Datadir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/share
Sysconfdir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/etc
Sharedstatedir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/com
Localstatedir: /home/apps/Logiciels/MPI/intel/openmpi/1.6/var
Infodir:
/home/apps/Logiciels/MPI/intel/openmpi/1.6/share/info
Pkgdatadir:
/home/apps/Logiciels/MPI/intel/openmpi/1.6/share/openmpi
Pkglibdir:
/home/apps/Logiciels/MPI/intel/openmpi/1.6/lib/openmpi
Pkgincludedir:
/home/apps/Logiciels/MPI/intel/openmpi/1.6/include/openmpi
Configured architecture: x86_64-unknown-linux-gnu
Configure host: briaree1
Configured by: rqchpbib
Configured on: Wed May 23 13:55:56 EDT 2012
Configure host: briaree1
Built by: rqchpbib
Built on: mer mai 23 14:56:29 EDT 2012
Built host: briaree1
C bindings: yes
C++ bindings: yes
Fortran77 bindings: yes (all)
Fortran90 bindings: yes
Fortran90 bindings size: small
C compiler: icc
C compiler absolute:
/home/apps/intel/composerxe-2011.4.191/bin/intel64/icc
C compiler family name: INTEL
C compiler version: 1200.20110427
C char size: 1
C bool size: 1
C short size: 2
C int size: 4
C long size: 8
C float size: 4
C double size: 8
C pointer size: 8
C char align: 1
C bool align: 1
C int align: 4
C float align: 4
C double align: 8
C++ compiler: icpc
C++ compiler absolute:
/home/apps/intel/composerxe-2011.4.191/bin/intel64/icpc
Fortran77 compiler: ifort
Fortran77 compiler abs:
/home/apps/intel/composerxe-2011.4.191/bin/intel64/ifort
Fortran90 compiler: ifort
Fortran90 compiler abs:
/home/apps/intel/composerxe-2011.4.191/bin/intel64/ifort
Fort integer size: 4
Fort logical size: 4
Fort logical value true: -1
Fort have integer1: yes
Fort have integer2: yes
Fort have integer4: yes
Fort have integer8: yes
Fort have integer16: no
Fort have real4: yes
Fort have real8: yes
Fort have real16: no
Fort have complex8: yes
Fort have complex16: yes
Fort have complex32: no
Fort integer1 size: 1
Fort integer2 size: 2
Fort integer4 size: 4
Fort integer8 size: 8
Fort integer16 size: -1
Fort real size: 4
Fort real4 size: 4
Fort real8 size: 8
Fort real16 size: 16
Fort dbl prec size: 8
Fort cplx size: 8
Fort dbl cplx size: 16
Fort cplx8 size: 8
Fort cplx16 size: 16
Fort cplx32 size: 32
Fort integer align: 1
Fort integer1 align: 1
Fort integer2 align: 1
Fort integer4 align: 1
Fort integer8 align: 1
Fort integer16 align: -1
Fort real align: 1
Fort real4 align: 1
Fort real8 align: 1
Fort real16 align: 1
Fort dbl prec align: 1
Fort cplx align: 1
Fort dbl cplx align: 1
Fort cplx8 align: 1
Fort cplx16 align: 1
Fort cplx32 align: 1
C profiling: yes
C++ profiling: yes
Fortran77 profiling: yes
Fortran90 profiling: yes
C++ exceptions: no
Thread support: posix (MPI_THREAD_MULTIPLE: no, progress: no)
Sparse Groups: no
Build CFLAGS: -DNDEBUG -g -O2 -finline-functions
-fno-strict-aliasing -restrict -pthread
Build CXXFLAGS: -O3 -DNDEBUG -finline-functions -pthread
Build FFLAGS:
Build FCFLAGS:
Build LDFLAGS: -export-dynamic
Build LIBS: -lrt -lnsl -lutil
Wrapper extra CFLAGS: -pthread
Wrapper extra CXXFLAGS: -pthread
Wrapper extra FFLAGS:
Wrapper extra FCFLAGS:
Wrapper extra LDFLAGS:
Wrapper extra LIBS: -ldl -lm -Wl,--export-dynamic -lrt -lnsl -lutil
Internal debug support: no
MPI interface warnings: no
MPI parameter check: runtime
Memory profiling support: no
Memory debugging support: no
libltdl support: yes
Heterogeneous support: no
mpirun default --prefix: no
MPI I/O support: yes
MPI_WTIME support: gettimeofday
Symbol vis. support: yes
Host topology support: yes
MPI extensions: affinity example
FT Checkpoint support: no (checkpoint thread: no)
VampirTrace support: yes
MPI_MAX_PROCESSOR_NAME: 256
MPI_MAX_ERROR_STRING: 256
MPI_MAX_OBJECT_NAME: 64
MPI_MAX_INFO_KEY: 36
MPI_MAX_INFO_VAL: 256
MPI_MAX_PORT_NAME: 1024
MPI_MAX_DATAREP_STRING: 128
MCA mca: parameter "mca_param_files" (current value:
</RQusagers/guertinf/.openmpi/mca-params.conf:/home/apps/Logiciels/MPI/intel/openmpi/1.6/etc/openmpi-mca-params.conf>,
data
source: default value)
Path for MCA configuration files containing
default parameter values
MCA mca: parameter "mca_base_param_file_prefix"
(current value: <none>, data source: default value)
Aggregate MCA parameter file sets
MCA mca: parameter "mca_base_param_file_path" (current
value:
</home/apps/Logiciels/MPI/intel/openmpi/1.6/share/openmpi/amca-param-sets:/exec5/GROUP/analyste/guertinf/numa_memoire>,
data
source: default value)
Aggregate MCA parameter Search path
MCA mca: parameter "mca_base_param_file_path_force"
(current value: <none>, data source: default value)
Forced Aggregate MCA parameter Search path
MCA mca: parameter "mca_component_path" (current value:
</home/apps/Logiciels/MPI/intel/openmpi/1.6/lib/openmpi:/RQusagers/guertinf/.openmpi/components>,
data source: default value)
Path where to look for Open MPI and ORTE
components
MCA mca: parameter "mca_component_show_load_errors"
(current value: <1>, data source: default value)
Whether to show errors for components that
failed to load or not
MCA mca: parameter "mca_component_disable_dlopen"
(current value: <0>, data source: default value)
Whether to attempt to disable opening dynamic
components or not
MCA mca: parameter "mca_verbose" (current value:
<stderr>, data source: default value)
Specifies where the default error output
stream goes (this is separate from distinct help messages). Accepts a
comma-delimited
list of: stderr, stdout, syslog,
syslogpri:<notice|info|debug>, syslogid:<str> (where str is the prefix
string for all syslog
notices), file[:filename] (if filename is not
specified, a default filename is used), fileappend (if not specified,
the file is
opened for truncation), level[:N] (if
specified, integer verbose level; otherwise, 0 is implied)
MCA mpi: parameter "mpi_paffinity_alone" (current
value: <0>, data source: default value, synonym of: opal_paffinity_alone)
If nonzero, assume that this job is the only
(set of) process(es) running on each node and bind processes to
processors, starting
with processor ID 0
MCA mpi: parameter "mpi_param_check" (current value:
<1>, data source: default value)
Whether you want MPI API parameters checked at
run-time or not. Possible values are 0 (no checking) and 1 (perform
checking at
run-time)
MCA mpi: parameter "mpi_yield_when_idle" (current
value: <-1>, data source: default value)
Yield the processor when waiting for MPI
communication (for MPI processes, will default to 1 when oversubscribing
nodes)
MCA mpi: parameter "mpi_event_tick_rate" (current
value: <-1>, data source: default value)
How often to progress TCP communications (0 =
never, otherwise specified in microseconds)
MCA mpi: parameter "mpi_show_handle_leaks" (current
value: <0>, data source: default value)
Whether MPI_FINALIZE shows all MPI handles
that were not freed or not
MCA mpi: parameter "mpi_no_free_handles" (current
value: <0>, data source: default value)
Whether to actually free MPI objects when
their handles are freed
MCA mpi: parameter "mpi_show_mpi_alloc_mem_leaks"
(current value: <0>, data source: default value)
If >0, MPI_FINALIZE will show up to this many
instances of memory allocated by MPI_ALLOC_MEM that was not freed by
MPI_FREE_MEM
MCA mpi: parameter "mpi_show_mca_params" (current
value: <none>, data source: default value)
Whether to show all MCA parameter values
during MPI_INIT or not (good for reproducability of MPI jobs for debug
purposes).
Accepted values are all, default, file, api,
and enviro - or a comma delimited combination of them
MCA mpi: parameter "mpi_show_mca_params_file" (current
value: <none>, data source: default value)
If mpi_show_mca_params is true, setting this
string to a valid filename tells Open MPI to dump all the MCA parameter
values into
a file suitable for reading via the
mca_param_files parameter (good for reproducability of MPI jobs)
MCA mpi: parameter "mpi_keep_peer_hostnames" (current
value: <1>, data source: default value)
If nonzero, save the string hostnames of all
MPI peer processes (mostly for error / debugging output messages). This
can add
quite a bit of memory usage to each MPI process.
MCA mpi: parameter "mpi_abort_delay" (current value:
<0>, data source: default value)
If nonzero, print out an identifying message
when MPI_ABORT is invoked (hostname, PID of the process that called
MPI_ABORT) and
delay for that many seconds before exiting (a
negative delay value means to never abort). This allows attaching of a
debugger
before quitting the job.
MCA mpi: parameter "mpi_abort_print_stack" (current
value: <0>, data source: default value)
If nonzero, print out a stack trace when
MPI_ABORT is invoked
MCA mpi: parameter "mpi_preconnect_mpi" (current value:
<0>, data source: default value, synonyms: mpi_preconnect_all)
Whether to force MPI processes to fully
wire-up the MPI connections between MPI processes during MPI_INIT (vs.
making connections
lazily -- upon the first MPI traffic between
each process peer pair)
MCA mpi: parameter "mpi_preconnect_all" (current value:
<0>, data source: default value, deprecated, synonym of: mpi_preconnect_mpi)
Whether to force MPI processes to fully
wire-up the MPI connections between MPI processes during MPI_INIT (vs.
making connections
lazily -- upon the first MPI traffic between
each process peer pair)
MCA mpi: parameter "mpi_leave_pinned" (current value:
<-1>, data source: default value)
Whether to use the "leave pinned" protocol or
not. Enabling this setting can help bandwidth performance when
repeatedly sending
and receiving large messages with the same
buffers over RDMA-based networks (0 = do not use "leave pinned"
protocol, 1 = use
"leave pinned" protocol, -1 = allow network to
choose at runtime).
MCA mpi: parameter "mpi_leave_pinned_pipeline" (current
value: <0>, data source: default value)
Whether to use the "leave pinned pipeline"
protocol or not.
MCA mpi: parameter "mpi_warn_on_fork" (current value:
<1>, data source: default value)
If nonzero, issue a warning if program forks
under conditions that could cause system errors
MCA mpi: information "mpi_have_sparse_group_storage"
(value: <0>, data source: default value)
Whether this Open MPI installation supports
storing of data in MPI groups in "sparse" formats (good for extremely
large process
count MPI jobs that create many
communicators/groups)
MCA mpi: parameter "mpi_use_sparse_group_storage"
(current value: <0>, data source: default value)
Whether to use "sparse" storage formats for
MPI groups (only relevant if mpi_have_sparse_group_storage is 1)
MCA mpi: parameter "mpi_notify_init_finalize" (current
value: <1>, data source: default value)
If nonzero, send two notifications during
MPI_INIT: one near when MPI_INIT starts, and another right before
MPI_INIT finishes,
and send 2 notifications during MPI_FINALIZE:
one right when MPI_FINALIZE starts, and another near when MPI_FINALIZE
finishes.
MCA orte: parameter "orte_base_help_aggregate" (current
value: <1>, data source: default value)
If orte_base_help_aggregate is true, duplicate
help messages will be aggregated rather than displayed individually.
This can be
helpful for parallel jobs that experience
multiple identical failures; rather than print out the same help/failure
message N
times, display it once with a count of how
many processes sent the same message.
MCA orte: parameter "orte_tmpdir_base" (current value:
<none>, data source: default value)
Base of the session directory tree
MCA orte: parameter "orte_no_session_dirs" (current
value: <none>, data source: default value)
Prohibited locations for session directories
(multiple locations separated by ',', default=NULL)
MCA orte: parameter "orte_send_profile" (current value:
<0>, data source: default value)
Send profile info in launch message
MCA orte: parameter "orte_debug" (current value: <0>,
data source: default value)
Top-level ORTE debug switch (default verbosity: 1)
MCA orte: parameter "orte_debug_verbose" (current value:
<-1>, data source: default value)
Verbosity level for ORTE debug messages
(default: 1)
MCA orte: parameter "orte_debug_daemons" (current value:
<0>, data source: default value)
Whether to debug the ORTE daemons or not
MCA orte: parameter "orte_debug_daemons_file" (current
value: <0>, data source: default value)
Whether want stdout/stderr of daemons to go to
a file or not
MCA orte: parameter "orte_daemon_bootstrap" (current
value: <0>, data source: default value)
Bootstrap the connection to the HNP
MCA orte: parameter "orte_leave_session_attached"
(current value: <0>, data source: default value)
Whether applications and/or daemons should
leave their sessions attached so that any output can be received - this
allows X
forwarding without all the attendant debugging
output
MCA orte: parameter "orte_output_debugger_proctable"
(current value: <0>, data source: default value)
Whether or not to output the debugger
proctable after launch (default: false)
MCA orte: parameter "orte_debugger_test_daemon" (current
value: <none>, data source: default value)
Name of the executable to be used to simulate
a debugger colaunch (relative or absolute path)
MCA orte: parameter "orte_debugger_test_attach" (current
value: <0>, data source: default value)
Test debugger colaunch after debugger attachment
MCA orte: parameter "orte_debugger_check_rate" (current
value: <0>, data source: default value)
Set rate (in secs) for auto-detect of debugger
attachment (0 => do not check)
MCA orte: parameter "orte_do_not_launch" (current value:
<0>, data source: default value)
Perform all necessary operations to prepare to
launch the application, but do not actually launch it
MCA orte: parameter "orte_daemon_spin" (current value:
<0>, data source: default value)
Have any orteds spin until we can connect a
debugger to them
MCA orte: parameter "orte_daemon_fail" (current value:
<-1>, data source: default value)
Have the specified orted fail after init for
debugging purposes
MCA orte: parameter "orte_daemon_fail_delay" (current
value: <0>, data source: default value)
Have the specified orted fail after specified
number of seconds (default: 0 => no delay)
MCA orte: parameter "orte_heartbeat_rate" (current
value: <0>, data source: default value)
Seconds between checks for daemon
state-of-health (default: 0 => do not check)
MCA orte: parameter "orte_startup_timeout" (current
value: <0>, data source: default value)
Milliseconds/daemon to wait for startup before
declaring failed_to_start (default: 0 => do not check)
MCA orte: parameter "orte_timing" (current value: <0>,
data source: default value)
Request that critical timing loops be measured
MCA orte: parameter "orte_timing_details" (current
value: <0>, data source: default value)
Request that detailed timing data by reported
MCA orte: parameter "orte_base_user_debugger" (current
value: <totalview @mpirun@ -a @mpirun_args@ : ddt -n @np@ -start
@executable@
@executable_argv@ @single_app@ : fxp @mpirun@
-a @mpirun_args@>, data source: default value)
Sequence of user-level debuggers to search for
in orterun
MCA orte: parameter "orte_abort_timeout" (current value:
<1>, data source: default value)
Max time to wait [in secs] before aborting an
ORTE operation (default: 1sec)
MCA orte: parameter "orte_timeout_step" (current value:
<1000>, data source: default value)
Time to wait [in usecs/proc] before aborting
an ORTE operation (default: 1000 usec/proc)
MCA orte: parameter "orte_default_hostfile" (current
value:
</home/apps/Logiciels/MPI/intel/openmpi/1.6/etc/openmpi-default-hostfile>,
data
source: default value)
Name of the default hostfile (relative or
absolute path, "none" to ignore environmental or default MCA param setting)
MCA orte: parameter "orte_rankfile" (current value:
<none>, data source: default value, synonyms: rmaps_rank_file_path)
Name of the rankfile to be used for mapping
processes (relative or absolute path)
MCA orte: parameter "orte_keep_fqdn_hostnames" (current
value: <0>, data source: default value)
Whether or not to keep FQDN hostnames
[default: no]
MCA orte: parameter "orte_use_regexp" (current value:
<0>, data source: default value)
Whether or not to use regular expressions for
launch [default: no]
MCA orte: parameter "orte_tag_output" (current value:
<0>, data source: default value)
Tag all output with [job,rank] (default: false)
MCA orte: parameter "orte_xml_output" (current value:
<0>, data source: default value)
Display all output in XML format (default: false)
MCA orte: parameter "orte_xml_file" (current value:
<none>, data source: default value)
Provide all output in XML format to the
specified file
MCA orte: parameter "orte_timestamp_output" (current
value: <0>, data source: default value)
Timestamp all application process output
(default: false)
MCA orte: parameter "orte_output_filename" (current
value: <none>, data source: default value)
Redirect output from application processes
into filename.rank [default: NULL]
MCA orte: parameter "orte_show_resolved_nodenames"
(current value: <0>, data source: default value)
Display any node names that are resolved to a
different name (default: false)
MCA orte: parameter "orte_hetero_apps" (current value:
<0>, data source: default value)
Indicates that multiple app_contexts are being
provided that are a mix of 32/64 bit binaries (default: false)
MCA orte: parameter "orte_launch_agent" (current value:
<orted>, data source: default value)
Command used to start processes on remote
nodes (default: orted)
MCA orte: parameter "orte_allocation_required" (current
value: <0>, data source: default value)
Whether or not an allocation by a resource
manager is required [default: no]
MCA orte: parameter "orte_xterm" (current value: <none>,
data source: default value)
Create a new xterm window and display output
from the specified ranks there [default: none]
MCA orte: parameter "orte_forward_job_control" (current
value: <0>, data source: default value)
Forward SIGTSTP (after converting to SIGSTOP)
and SIGCONT signals to the application procs [default: no]
MCA orte: parameter "orte_rsh_agent" (current value:
<ssh : rsh>, data source: default value, synonyms: pls_rsh_agent,
plm_rsh_agent)
The command used to launch executables on
remote nodes (typically either "ssh" or "rsh")
MCA orte: parameter "orte_assume_same_shell" (current
value: <1>, data source: default value, synonyms: plm_rsh_assume_same_shell)
If set to 1, assume that the shell on the
remote node is the same as the shell on the local node. Otherwise,
probe for what the
remote shell [default: 1]
MCA orte: parameter "orte_report_launch_progress"
(current value: <0>, data source: default value)
Output a brief periodic report on launch
progress [default: no]
MCA orte: parameter "orte_num_boards" (current value:
<1>, data source: default value)
Number of processor boards/node (1-256)
[default: 1]
MCA orte: parameter "orte_num_sockets" (current value:
<0>, data source: default value)
Number of sockets/board (1-256)
MCA orte: parameter "orte_num_cores" (current value:
<0>, data source: default value)
Number of cores/socket (1-256)
MCA orte: parameter "orte_cpu_set" (current value:
<none>, data source: default value)
Comma-separated list of ranges specifying
logical cpus allocated to this job [default: none]
MCA orte: parameter "orte_process_binding" (current
value: <none>, data source: default value)
Policy for binding processes [none | core |
socket | board] (supported qualifier: if-avail)
MCA orte: parameter "orte_report_bindings" (current
value: <0>, data source: default value)
Report bindings
MCA orte: parameter "orte_report_events" (current value:
<none>, data source: default value)
URI to which events are to be reported
(default: NULL)]
MCA opal: parameter "opal_net_private_ipv4" (current
value: <10.0.0.0/8;172.16.0.0/12;192.168.0.0/16;169.254.0.0/16>, data
source: default
value)
Semicolon-delimited list of CIDR notation
entries specifying what networks are considered "private" (default value
based on
RFC1918 and RFC3330)
MCA opal: parameter "opal_signal" (current value:
<6,7,8,11>, data source: default value)
Comma-delimited list of integer signal numbers
to Open MPI to attempt to intercept. Upon receipt of the intercepted
signal, Open
MPI will display a stack trace and abort.
Open MPI will *not* replace signals if handlers are already installed by
the time
MPI_INIT is invoked. Optionally append
":complain" to any signal number in the comma-delimited list to make
Open MPI complain if
it detects another signal handler (and
therefore does not insert its own).
MCA opal: parameter "opal_profile" (current value: <0>,
data source: default value)
Set to non-zero to profile component selections
MCA opal: parameter "opal_profile_file" (current value:
<none>, data source: default value)
Name of the file containing the cluster
configuration information
MCA opal: parameter "opal_paffinity_alone" (current
value: <0>, data source: default value, synonyms: mpi_paffinity_alone)
If nonzero, assume that this job is the only
(set of) process(es) running on each node and bind processes to
processors, starting
with processor ID 0
MCA opal: parameter "opal_set_max_sys_limits" (current
value: <0>, data source: default value)
Set to non-zero to automatically set any
system-imposed limits to the maximum allowed
MCA opal: parameter "opal_event_include" (current value:
<poll>, data source: default value)
Comma-delimited list of libevent subsystems to
use (epoll, poll, select -- available on your platform)
MCA backtrace: parameter "backtrace" (current value: <none>,
data source: default value)
Default selection set of components for the
backtrace framework (<none> means use all components that can be found)
MCA backtrace: parameter "backtrace_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the backtrace framework (0
= no verbosity)
MCA backtrace: parameter "backtrace_execinfo_priority"
(current value: <0>, data source: default value)
MCA memchecker: parameter "memchecker" (current value: <none>,
data source: default value)
Default selection set of components for the
memchecker framework (<none> means use all components that can be found)
MCA memory: parameter "memory" (current value: <none>,
data source: default value)
Default selection set of components for the
memory framework (<none> means use all components that can be found)
MCA memory: parameter "memory_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the memory framework (0 =
no verbosity)
MCA memory: information "memory_linux_ptmalloc2_available"
(value: <1>, data source: default value)
Whether ptmalloc2 support is included in Open
MPI or not (1 = yes, 0 = no)
MCA memory: information
"memory_linux_ummunotify_available" (value: <0>, data source: default value)
Whether ummunotify support is included in Open
MPI or not (1 = yes, 0 = no)
MCA memory: parameter "memory_linux_ptmalloc2_enable"
(current value: <-1>, data source: default value)
Whether to enable ptmalloc2 support or not
(negative = try to enable, but continue even if support is not
available, 0 = do not
enable support, positive = try to enable and
fail if support is not available)
MCA memory: parameter "memory_linux_ummunotify_enable"
(current value: <-1>, data source: default value)
Whether to enable ummunotify support or not
(negative = try to enable, but continue even if support is not
available, 0 = do not
enable support, positive = try to enable and
fail if support is not available)
MCA memory: parameter "memory_linux_disable" (current
value: <0>, data source: default value)
If this MCA parameter is set to 1 **VIA
ENVIRONMENT VARIABLE ONLY*** (this MCA parameter *CANNOT* be set in a
file or on the
mpirun command line!), this component will be
disabled and will not attempt to use either ummunotify or memory hook
support
MCA memory: parameter "memory_linux_priority" (current
value: <0>, data source: default value)
MCA paffinity: parameter "paffinity_base_verbose" (current
value: <0>, data source: default value)
Verbosity level of the paffinity framework
MCA paffinity: parameter "paffinity" (current value: <none>,
data source: default value)
Default selection set of components for the
paffinity framework (<none> means use all components that can be found)
MCA paffinity: parameter "paffinity_hwloc_priority" (current
value: <40>, data source: default value)
Priority of the hwloc paffinity component
MCA carto: parameter "carto_base_verbose" (current value:
<0>, data source: default value)
Verbosity level of the carto framework
MCA carto: parameter "carto" (current value: <none>, data
source: default value)
Default selection set of components for the
carto framework (<none> means use all components that can be found)
MCA carto: parameter "carto_auto_detect_priority"
(current value: <11>, data source: default value)
Priority of the auto_detect carto component
MCA carto: parameter "carto_file_path" (current value:
<none>, data source: default value)
The path to the cartography file
MCA carto: parameter "carto_file_priority" (current
value: <10>, data source: default value)
Priority of the file carto component
MCA shmem: parameter "shmem_base_verbose" (current value:
<0>, data source: default value)
Verbosity level of the shmem framework
MCA shmem: parameter "shmem" (current value: <none>, data
source: default value)
Default selection set of components for the
shmem framework (<none> means use all components that can be found)
MCA shmem: parameter "shmem_mmap_enable_nfs_warning"
(current value: <1>, data source: default value)
Enable the warning emitted when Open MPI
detects that its shared memory backing file is located on a network
filesystem (1 =
enabled, 0 = disabled).
MCA shmem: parameter "shmem_mmap_priority" (current
value: <50>, data source: default value)
Priority of the mmap shmem component
MCA shmem: parameter "shmem_mmap_relocate_backing_file"
(current value: <0>, data source: default value)
Whether to change the default placement of
backing files or not (Negative = try to relocate backing files to an
area rooted at
the path specified by
shmem_mmap_opal_shmem_mmap_backing_file_base_dir, but continue with the
default path if the relocation
fails, 0 = do not relocate, Positive = same as
the negative option, but will fail if the relocation fails.
MCA shmem: parameter "shmem_mmap_backing_file_base_dir"
(current value: </dev/shm>, data source: default value)
Specifies where backing files will be created
when shmem_mmap_relocate_backing_file is in use.
MCA shmem: parameter "shmem_posix_priority" (current
value: <40>, data source: default value)
Priority of the posix shmem component
MCA shmem: parameter "shmem_sysv_priority" (current
value: <30>, data source: default value)
Priority of the sysv shmem component
MCA maffinity: parameter "maffinity_base_verbose" (current
value: <0>, data source: default value)
Verbosity level of the maffinity framework
MCA maffinity: parameter "maffinity" (current value: <none>,
data source: default value)
Default selection set of components for the
maffinity framework (<none> means use all components that can be found)
MCA maffinity: parameter "maffinity_hwloc_priority" (current
value: <40>, data source: default value)
Priority of the hwloc maffinity component
MCA timer: parameter "timer" (current value: <none>, data
source: default value)
Default selection set of components for the
timer framework (<none> means use all components that can be found)
MCA timer: parameter "timer_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the timer framework (0 =
no verbosity)
MCA timer: parameter "timer_linux_priority" (current
value: <0>, data source: default value)
MCA sysinfo: parameter "sysinfo" (current value: <none>,
data source: default value)
Default selection set of components for the
sysinfo framework (<none> means use all components that can be found)
MCA sysinfo: parameter "sysinfo_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the sysinfo framework (0 =
no verbosity)
MCA sysinfo: parameter "sysinfo_linux_priority" (current
value: <0>, data source: default value)
MCA hwloc: parameter "hwloc_base_verbose" (current value:
<0>, data source: default value)
Verbosity level of the hwloc framework
MCA hwloc: parameter "hwloc_base_mem_alloc_policy"
(current value: <none>, data source: default value)
Policy that determines how general memory
allocations are bound after MPI_INIT. A value of "none" means that no
memory policy is
applied. A value of "local_only" means that
all memory allocations will be restricted to the local NUMA node where
each process
is placed. Note that operating system paging
policies are unaffected by this setting. For example, if "local_only"
is used and
local NUMA node memory is exhausted, a new
memory allocation may cause paging.
MCA hwloc: parameter "hwloc_base_mem_bind_failure_action"
(current value: <error>, data source: default value)
What Open MPI will do if it explicitly tries
to bind memory to a specific NUMA location, and fails. Note that this is a
different case than the general allocation
policy described by hwloc_base_alloc_policy. A value of "warn" means
that Open MPI
will warn the first time this happens, but
allow the job to continue (possibly with degraded performance). A value
of "error"
means that Open MPI will abort the job if this
happens.
MCA hwloc: parameter "hwloc" (current value: <none>, data
source: default value)
Default selection set of components for the
hwloc framework (<none> means use all components that can be found)
MCA hwloc: parameter "hwloc_hwloc132_priority" (current
value: <0>, data source: default value)
MCA dpm: parameter "dpm" (current value: <none>, data
source: default value)
Default selection set of components for the
dpm framework (<none> means use all components that can be found)
MCA dpm: parameter "dpm_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the dpm framework (0 = no
verbosity)
MCA dpm: parameter "dpm_orte_priority" (current value:
<0>, data source: default value)
MCA pubsub: parameter "pubsub" (current value: <none>,
data source: default value)
Default selection set of components for the
pubsub framework (<none> means use all components that can be found)
MCA pubsub: parameter "pubsub_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the pubsub framework (0 =
no verbosity)
MCA pubsub: parameter "pubsub_orte_priority" (current
value: <50>, data source: default value)
Priority of the pubsub pmi component
MCA allocator: parameter "allocator" (current value: <none>,
data source: default value)
Default selection set of components for the
allocator framework (<none> means use all components that can be found)
MCA allocator: parameter "allocator_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the allocator framework (0
= no verbosity)
MCA allocator: parameter "allocator_basic_priority" (current
value: <0>, data source: default value)
MCA allocator: parameter "allocator_bucket_num_buckets"
(current value: <30>, data source: default value)
MCA allocator: parameter "allocator_bucket_priority" (current
value: <0>, data source: default value)
MCA coll: parameter "coll" (current value: <none>, data
source: default value)
Default selection set of components for the
coll framework (<none> means use all components that can be found)
MCA coll: parameter "coll_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the coll framework (0 = no
verbosity)
MCA coll: parameter "coll_basic_priority" (current
value: <10>, data source: default value)
Priority of the basic coll component
MCA coll: parameter "coll_basic_crossover" (current
value: <4>, data source: default value)
Minimum number of processes in a communicator
before using the logarithmic algorithms
MCA coll: parameter "coll_hierarch_priority" (current
value: <0>, data source: default value)
Priority of the hierarchical coll component
MCA coll: parameter "coll_hierarch_verbose" (current
value: <0>, data source: default value)
Turn verbose message of the hierarchical coll
component on/off
MCA coll: parameter "coll_hierarch_use_rdma" (current
value: <0>, data source: default value)
Switch from the send btl list used to detect
hierarchies to the rdma btl list
MCA coll: parameter "coll_hierarch_ignore_sm" (current
value: <0>, data source: default value)
Ignore sm protocol when detecting hierarchies.
Required to enable the usage of protocol specific collective operations
MCA coll: parameter "coll_hierarch_detection_alg"
(current value: <2>, data source: default value)
Used to specify the algorithm for detecting
Hierarchy.Choose between all or two levels of hierarchy
MCA coll: parameter "coll_hierarch_bcast_alg" (current
value: <4>, data source: default value)
Used to specify the algorithm used for bcast
operations.
MCA coll: parameter "coll_hierarch_segment_size"
(current value: <32768>, data source: default value)
Used to specify the segment size for segmented
algorithms.
MCA coll: parameter "coll_inter_priority" (current
value: <40>, data source: default value)
Priority of the inter coll component
MCA coll: parameter "coll_inter_verbose" (current value:
<0>, data source: default value)
Turn verbose message of the inter coll
component on/off
MCA coll: parameter "coll_self_priority" (current value:
<75>, data source: default value)
MCA coll: parameter "coll_sm_priority" (current value:
<0>, data source: default value)
Priority of the sm coll component
MCA coll: parameter "coll_sm_control_size" (current
value: <4096>, data source: default value)
Length of the control data -- should usually
be either the length of a cache line on most SMPs, or the size of a page
on machines
that support direct memory affinity page
placement (in bytes)
MCA coll: parameter "coll_sm_fragment_size" (current
value: <8192>, data source: default value)
Fragment size (in bytes) used for passing data
through shared memory (will be rounded up to the nearest control_size size)
MCA coll: parameter "coll_sm_comm_in_use_flags" (current
value: <2>, data source: default value)
Number of "in use" flags, used to mark a
message passing area segment as currently being used or not (must be >=
2 and <=
comm_num_segments)
MCA coll: parameter "coll_sm_comm_num_segments" (current
value: <8>, data source: default value)
Number of segments in each communicator's
shared memory message passing area (must be >= 2, and must be a multiple of
comm_in_use_flags)
MCA coll: parameter "coll_sm_tree_degree" (current
value: <4>, data source: default value)
Degree of the tree for tree-based operations
(must be => 1 and <= min(control_size, 255))
MCA coll: parameter "coll_sm_info_num_procs" (current
value: <4>, data source: default value)
Number of processes to use for the calculation
of the shared_mem_size MCA information parameter (must be => 2)
MCA coll: information "coll_sm_shared_mem_used_data"
(value: <548864>, data source: default value)
Amount of shared memory used, per
communicator, in the shared memory data area for info_num_procs
processes (in bytes)
MCA coll: parameter "coll_sync_priority" (current value:
<50>, data source: default value)
Priority of the sync coll component; only
relevant if barrier_before or barrier_after is > 0
MCA coll: parameter "coll_sync_barrier_before" (current
value: <1000>, data source: default value)
Do a synchronization before each Nth collective
MCA coll: parameter "coll_sync_barrier_after" (current
value: <0>, data source: default value)
Do a synchronization after each Nth collective
MCA coll: parameter "coll_tuned_priority" (current
value: <30>, data source: default value)
Priority of the tuned coll component
MCA coll: parameter
"coll_tuned_pre_allocate_memory_comm_size_limit" (current value:
<32768>, data source: default value)
Size of communicator were we stop
pre-allocating memory for the fixed internal buffer used for message
requests etc that is hung
off the communicator data segment. I.e. if you
have a 100'000 nodes you might not want to pre-allocate 200'000 request
handle
slots per communicator instance!
MCA coll: parameter "coll_tuned_init_tree_fanout"
(current value: <4>, data source: default value)
Inital fanout used in the tree topologies for
each communicator. This is only an initial guess, if a tuned collective
needs a
different fanout for an operation, it build it
dynamically. This parameter is only for the first guess and might save a
little
time
MCA coll: parameter "coll_tuned_init_chain_fanout"
(current value: <4>, data source: default value)
Inital fanout used in the chain (fanout
followed by pipeline) topologies for each communicator. This is only an
initial guess, if
a tuned collective needs a different fanout
for an operation, it build it dynamically. This parameter is only for
the first guess
and might save a little time
MCA coll: parameter "coll_tuned_use_dynamic_rules"
(current value: <0>, data source: default value)
Switch used to decide if we use static
(compiled/if statements) or dynamic (built at runtime) decision function
rules
MCA io: parameter "io_base_freelist_initial_size"
(current value: <16>, data source: default value)
Initial MPI-2 IO request freelist size
MCA io: parameter "io_base_freelist_max_size" (current
value: <64>, data source: default value)
Max size of the MPI-2 IO request freelist
MCA io: parameter "io_base_freelist_increment"
(current value: <16>, data source: default value)
Increment size of the MPI-2 IO request freelist
MCA io: parameter "io" (current value: <none>, data
source: default value)
Default selection set of components for the io
framework (<none> means use all components that can be found)
MCA io: parameter "io_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the io framework (0 = no
verbosity)
MCA io: parameter "io_romio_priority" (current value:
<10>, data source: default value)
Priority of the io romio component
MCA io: parameter "io_romio_delete_priority" (current
value: <10>, data source: default value)
Delete priority of the io romio component
MCA io: information "io_romio_version" (value: <from
MPICH2 v1.3.1 with an additional patch from [email protected] about an
attribute issue>, data source: default value)
Version of ROMIO
MCA io: information "io_romio_user_configure_params"
(value: <none>, data source: default value)
User-specified command line parameters passed
to ROMIO's configure script
MCA io: information
"io_romio_complete_configure_params" (value: < CFLAGS='-DNDEBUG -g -O2
-finline-functions -fno-strict-aliasing
-restrict -pthread' CPPFLAGS='
-I/RQusagers/rqchpbib/Compilation/openmpi-1.6/opal/mca/hwloc/hwloc132/hwloc/include
-I/usr/include/infiniband
-I/usr/include/infiniband' FFLAGS='' LDFLAGS=' ' --enable-shared
--disable-static
--prefix=/home/apps/Logiciels/MPI/intel/openmpi/1.6 --with-mpi=open_mpi
--disable-aio>, data source: default value)
Complete set of command line parameters passed
to ROMIO's configure script
MCA mpool: parameter "mpool" (current value: <none>, data
source: default value)
Default selection set of components for the
mpool framework (<none> means use all components that can be found)
MCA mpool: parameter "mpool_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the mpool framework (0 =
no verbosity)
MCA mpool: parameter "mpool_fake_priority" (current
value: <0>, data source: default value)
MCA mpool: parameter "mpool_rdma_rcache_name" (current
value: <vma>, data source: default value)
The name of the registration cache the mpool
should use
MCA mpool: parameter "mpool_rdma_rcache_size_limit"
(current value: <0>, data source: default value)
the maximum size of registration cache in
bytes. 0 is unlimited (default 0)
MCA mpool: parameter "mpool_rdma_print_stats" (current
value: <0>, data source: default value)
print pool usage statistics at the end of the run
MCA mpool: parameter "mpool_rdma_priority" (current
value: <0>, data source: default value)
MCA mpool: parameter "mpool_sm_allocator" (current value:
<bucket>, data source: default value)
Name of allocator component to use with sm mpool
MCA mpool: parameter "mpool_sm_min_size" (current value:
<67108864>, data source: default value)
Minimum size of the sm mpool shared memory file
MCA mpool: parameter "mpool_sm_verbose" (current value:
<0>, data source: default value)
Enable verbose output for mpool sm component
MCA mpool: parameter "mpool_sm_priority" (current value:
<0>, data source: default value)
MCA pml: parameter "pml_base_verbose" (current value:
<0>, data source: default value)
Verbosity level of the PML framework
MCA pml: parameter "pml" (current value: <none>, data
source: default value)
Default selection set of components for the
pml framework (<none> means use all components that can be found)
MCA pml: parameter "pml_bfo_verbose" (current value:
<0>, data source: default value)
MCA pml: parameter "pml_bfo_free_list_num" (current
value: <4>, data source: default value)
MCA pml: parameter "pml_bfo_free_list_max" (current
value: <-1>, data source: default value)
MCA pml: parameter "pml_bfo_free_list_inc" (current
value: <64>, data source: default value)
MCA pml: parameter "pml_bfo_priority" (current value:
<5>, data source: default value)
MCA pml: parameter "pml_bfo_send_pipeline_depth"
(current value: <3>, data source: default value)
MCA pml: parameter "pml_bfo_recv_pipeline_depth"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_bfo_rdma_put_retries_limit"
(current value: <5>, data source: default value)
MCA pml: parameter "pml_bfo_max_rdma_per_request"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_bfo_max_send_per_range"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_bfo_unexpected_limit" (current
value: <128>, data source: default value)
MCA pml: parameter "pml_bfo_allocator" (current value:
<bucket>, data source: default value)
Name of allocator component for unexpected
messages
MCA pml: parameter "pml_cm_free_list_num" (current
value: <4>, data source: default value)
Initial size of request free lists
MCA pml: parameter "pml_cm_free_list_max" (current
value: <-1>, data source: default value)
Maximum size of request free lists
MCA pml: parameter "pml_cm_free_list_inc" (current
value: <64>, data source: default value)
Number of elements to add when growing request
free lists
MCA pml: parameter "pml_cm_priority" (current value:
<10>, data source: default value)
CM PML selection priority
MCA pml: parameter "pml_csum_free_list_num" (current
value: <4>, data source: default value)
MCA pml: parameter "pml_csum_free_list_max" (current
value: <-1>, data source: default value)
MCA pml: parameter "pml_csum_free_list_inc" (current
value: <64>, data source: default value)
MCA pml: parameter "pml_csum_send_pipeline_depth"
(current value: <3>, data source: default value)
MCA pml: parameter "pml_csum_recv_pipeline_depth"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_csum_rdma_put_retries_limit"
(current value: <5>, data source: default value)
MCA pml: parameter "pml_csum_max_rdma_per_request"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_csum_max_send_per_range"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_csum_unexpected_limit" (current
value: <128>, data source: default value)
MCA pml: parameter "pml_csum_allocator" (current value:
<bucket>, data source: default value)
Name of allocator component for unexpected
messages
MCA pml: parameter "pml_csum_priority" (current value:
<0>, data source: default value)
MCA pml: parameter "pml_ob1_free_list_num" (current
value: <4>, data source: default value)
MCA pml: parameter "pml_ob1_free_list_max" (current
value: <-1>, data source: default value)
MCA pml: parameter "pml_ob1_free_list_inc" (current
value: <64>, data source: default value)
MCA pml: parameter "pml_ob1_priority" (current value:
<20>, data source: default value)
MCA pml: parameter "pml_ob1_send_pipeline_depth"
(current value: <3>, data source: default value)
MCA pml: parameter "pml_ob1_recv_pipeline_depth"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_ob1_rdma_put_retries_limit"
(current value: <5>, data source: default value)
MCA pml: parameter "pml_ob1_max_rdma_per_request"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_ob1_max_send_per_range"
(current value: <4>, data source: default value)
MCA pml: parameter "pml_ob1_unexpected_limit" (current
value: <128>, data source: default value)
MCA pml: parameter "pml_ob1_allocator" (current value:
<bucket>, data source: default value)
Name of allocator component for unexpected
messages
MCA pml: parameter "pml_v_priority" (current value:
<-1>, data source: default value)
MCA pml: parameter "pml_v_output" (current value:
<stderr>, data source: default value)
MCA pml: parameter "pml_v_verbose" (current value: <0>,
data source: default value)
MCA bml: parameter "bml" (current value: <none>, data
source: default value)
Default selection set of components for the
bml framework (<none> means use all components that can be found)
MCA bml: parameter "bml_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the bml framework (0 = no
verbosity)
MCA bml: parameter "bml_r2_show_unreach_errors"
(current value: <1>, data source: default value)
Show error message when procs are unreachable
MCA bml: parameter "bml_r2_priority" (current value:
<0>, data source: default value)
MCA rcache: parameter "rcache" (current value: <none>,
data source: default value)
Default selection set of components for the
rcache framework (<none> means use all components that can be found)
MCA rcache: parameter "rcache_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the rcache framework (0 =
no verbosity)
MCA rcache: parameter "rcache_vma_priority" (current
value: <0>, data source: default value)
MCA btl: parameter "btl_base_verbose" (current value:
<0>, data source: default value)
Verbosity level of the BTL framework
MCA btl: parameter "btl" (current value: <none>, data
source: default value)
Default selection set of components for the
btl framework (<none> means use all components that can be found)
MCA btl: parameter "btl_ofud_max_btls" (current value:
<4>, data source: default value)
Maximum number of HCAs/ports to use
MCA btl: parameter "btl_ofud_if_include" (current
value: <none>, data source: default value)
Comma-delimited list of HCAs/ports to be used;
empty value means to use all HCAs/ports found
MCA btl: parameter "btl_ofud_if_exclude" (current
value: <none>, data source: default value)
Comma-delimited list of HCAs/ports to be
excluded; empty value means to use all HCAs/ports found
MCA btl: parameter "btl_ofud_mpool" (current value:
<rdma>, data source: default value)
Name of the memory pool to be used
MCA btl: parameter "btl_ofud_ib_pkey_index" (current
value: <0>, data source: default value)
IB pkey index
MCA btl: parameter "btl_ofud_ib_qkey" (current value:
<20119859>, data source: default value)
IB qkey
MCA btl: parameter "btl_ofud_ib_service_level" (current
value: <0>, data source: default value)
IB service level
MCA btl: parameter "btl_ofud_ib_src_path_bits" (current
value: <0>, data source: default value)
IB source path bits
MCA btl: parameter "btl_ofud_sd_num" (current value:
<128>, data source: default value)
maximum send descriptors to post
MCA btl: parameter "btl_ofud_rd_num" (current value:
<6000>, data source: default value)
number of receive buffers
MCA btl: parameter "btl_ofud_min_send_size" (current
value: <2048>, data source: default value)
minimum send size
MCA btl: parameter "btl_ofud_max_send_size" (current
value: <2048>, data source: default value)
maximum send size
MCA btl: parameter "btl_ofud_exclusivity" (current
value: <1024>, data source: default value)
BTL exclusivity
MCA btl: parameter "btl_ofud_bandwidth" (current value:
<800>, data source: default value)
Approximate maximum bandwidth of interconnect
MCA btl: parameter "btl_ofud_priority" (current value:
<0>, data source: default value)
MCA btl: parameter "btl_openib_verbose" (current value:
<0>, data source: default value)
Output some verbose OpenIB BTL information (0
= no output, nonzero = output)
MCA btl: parameter
"btl_openib_warn_no_device_params_found" (current value: <1>, data
source: default value, synonyms:
btl_openib_warn_no_hca_params_found)
Warn when no device-specific parameters are
found in the INI file specified by the btl_openib_device_param_files MCA
parameter (0
= do not warn; any other value = warn)
MCA btl: parameter
"btl_openib_warn_no_hca_params_found" (current value: <1>, data source:
default value, deprecated, synonym of:
btl_openib_warn_no_device_params_found)
Warn when no device-specific parameters are
found in the INI file specified by the btl_openib_device_param_files MCA
parameter (0
= do not warn; any other value = warn)
MCA btl: parameter "btl_openib_warn_default_gid_prefix"
(current value: <1>, data source: default value)
Warn when there is more than one active ports
and at least one of them connected to the network with only default GID
prefix
configured (0 = do not warn; any other value =
warn)
MCA btl: parameter "btl_openib_warn_nonexistent_if"
(current value: <1>, data source: default value)
Warn if non-existent devices and/or ports are
specified in the btl_openib_if_[in|ex]clude MCA parameters (0 = do not
warn; any
other value = warn)
MCA btl: parameter "btl_openib_want_fork_support"
(current value: <-1>, data source: default value)
Whether fork support is desired or not
(negative = try to enable fork support, but continue even if it is not
available, 0 = do
not enable fork support, positive = try to
enable fork support and fail if it is not available)
MCA btl: parameter "btl_openib_device_param_files"
(current value:
</home/apps/Logiciels/MPI/intel/openmpi/1.6/share/openmpi/mca-btl-openib-device-params.ini>,
data source: default value,
synonyms: btl_openib_hca_param_files)
Colon-delimited list of INI-style files that
contain device vendor/part-specific parameters
MCA btl: parameter "btl_openib_hca_param_files"
(current value:
</home/apps/Logiciels/MPI/intel/openmpi/1.6/share/openmpi/mca-btl-openib-device-params.ini>,
data source: default value,
deprecated, synonym of:
btl_openib_device_param_files)
Colon-delimited list of INI-style files that
contain device vendor/part-specific parameters
MCA btl: parameter "btl_openib_device_type" (current
value: <all>, data source: default value)
Specify to only use IB or iWARP network
adapters (infiniband = only use InfiniBand HCAs; iwarp = only use iWARP
NICs; all = use
any available adapters)
MCA btl: parameter "btl_openib_max_btls" (current
value: <-1>, data source: default value)
Maximum number of device ports to use (-1 =
use all available, otherwise must be >= 1)
MCA btl: parameter "btl_openib_free_list_num" (current
value: <8>, data source: default value)
Initial size of free lists (must be >= 1)
MCA btl: parameter "btl_openib_free_list_max" (current
value: <-1>, data source: default value)
Maximum size of free lists (-1 = infinite,
otherwise must be >= 0)
MCA btl: parameter "btl_openib_free_list_inc" (current
value: <32>, data source: default value)
Increment size of free lists (must be >= 1)
MCA btl: parameter "btl_openib_mpool" (current value:
<rdma>, data source: default value)
Name of the memory pool to be used (it is
unlikely that you will ever want to change this)
MCA btl: parameter "btl_openib_reg_mru_len" (current
value: <16>, data source: default value)
Length of the registration cache most recently
used list (must be >= 1)
MCA btl: parameter "btl_openib_cq_size" (current value:
<1000>, data source: default value, synonyms: btl_openib_ib_cq_size)
Minimum size of the OpenFabrics completion
queue (CQs are automatically sized based on the number of peer MPI
processes; this
value determines the *minimum* size of all CQs)
MCA btl: parameter "btl_openib_ib_cq_size" (current
value: <1000>, data source: default value, deprecated, synonym of:
btl_openib_cq_size)
Minimum size of the OpenFabrics completion
queue (CQs are automatically sized based on the number of peer MPI
processes; this
value determines the *minimum* size of all CQs)
MCA btl: parameter "btl_openib_max_inline_data"
(current value: <-1>, data source: default value, synonyms:
btl_openib_ib_max_inline_data)
Maximum size of inline data segment (-1 =
run-time probe to discover max value, otherwise must be >= 0). If not
explicitly set,
use max_inline_data from the INI file
containing device-specific parameters
MCA btl: parameter "btl_openib_ib_max_inline_data"
(current value: <-1>, data source: default value, deprecated, synonym of:
btl_openib_max_inline_data)
Maximum size of inline data segment (-1 =
run-time probe to discover max value, otherwise must be >= 0). If not
explicitly set,
use max_inline_data from the INI file
containing device-specific parameters
MCA btl: parameter "btl_openib_pkey" (current value:
<0>, data source: default value, synonyms: btl_openib_ib_pkey_val)
OpenFabrics partition key (pkey) value.
Unsigned integer decimal or hex values are allowed (e.g., "3" or "0x3f")
and will be
masked against the maximum allowable IB
partition key value (0x7fff)
MCA btl: parameter "btl_openib_ib_pkey_val" (current
value: <0>, data source: default value, deprecated, synonym of:
btl_openib_pkey)
OpenFabrics partition key (pkey) value.
Unsigned integer decimal or hex values are allowed (e.g., "3" or "0x3f")
and will be
masked against the maximum allowable IB
partition key value (0x7fff)
MCA btl: parameter "btl_openib_psn" (current value:
<0>, data source: default value, synonyms: btl_openib_ib_psn)
OpenFabrics packet sequence starting number
(must be >= 0)
MCA btl: parameter "btl_openib_ib_psn" (current value:
<0>, data source: default value, deprecated, synonym of: btl_openib_psn)
OpenFabrics packet sequence starting number
(must be >= 0)
MCA btl: parameter "btl_openib_ib_qp_ous_rd_atom"
(current value: <4>, data source: default value)
InfiniBand outstanding atomic reads (must be >= 0)
MCA btl: parameter "btl_openib_mtu" (current value:
<3>, data source: default value, synonyms: btl_openib_ib_mtu)
OpenFabrics MTU, in bytes (if not specified in
INI files). Valid values are: 1=256 bytes, 2=512 bytes, 3=1024 bytes,
4=2048
bytes, 5=4096 bytes
MCA btl: parameter "btl_openib_ib_mtu" (current value:
<3>, data source: default value, deprecated, synonym of: btl_openib_mtu)
OpenFabrics MTU, in bytes (if not specified in
INI files). Valid values are: 1=256 bytes, 2=512 bytes, 3=1024 bytes,
4=2048
bytes, 5=4096 bytes
MCA btl: parameter "btl_openib_ib_min_rnr_timer"
(current value: <25>, data source: default value)
InfiniBand minimum "receiver not ready" timer,
in seconds (must be >= 0 and <= 31)
MCA btl: parameter "btl_openib_ib_timeout" (current
value: <20>, data source: default value)
InfiniBand transmit timeout, plugged into
formula: 4.096 microseconds * (2^btl_openib_ib_timeout) (must be >= 0
and <= 31)
MCA btl: parameter "btl_openib_ib_retry_count" (current
value: <7>, data source: default value)
InfiniBand transmit retry count (must be >= 0
and <= 7)
MCA btl: parameter "btl_openib_ib_rnr_retry" (current
value: <7>, data source: default value)
InfiniBand "receiver not ready" retry count;
applies *only* to SRQ/XRC queues. PP queues use RNR retry values of 0
because Open
MPI performs software flow control to
guarantee that RNRs never occur (must be >= 0 and <= 7; 7 = "infinite")
MCA btl: parameter "btl_openib_ib_max_rdma_dst_ops"
(current value: <4>, data source: default value)
InfiniBand maximum pending RDMA destination
operations (must be >= 0)
MCA btl: parameter "btl_openib_ib_service_level"
(current value: <0>, data source: default value)
InfiniBand service level (must be >= 0 and <= 15)
MCA btl: parameter
"btl_openib_ib_path_record_service_level" (current value: <0>, data
source: default value)
Enable getting InfiniBand service level from
PathRecord (must be >= 0, 0 = disabled, positive = try to get the
service level from
PathRecord)
MCA btl: parameter "btl_openib_use_eager_rdma" (current
value: <-1>, data source: default value)
Use RDMA for eager messages (-1 = use device
default, 0 = do not use eager RDMA, 1 = use eager RDMA)
MCA btl: parameter "btl_openib_eager_rdma_threshold"
(current value: <16>, data source: default value)
Use RDMA for short messages after this number
of messages are received from a given peer (must be >= 1)
MCA btl: parameter "btl_openib_max_eager_rdma" (current
value: <16>, data source: default value)
Maximum number of peers allowed to use RDMA
for short messages (RDMA is used for all long messages, except if explicitly
disabled, such as with the "dr" pml) (must be
>= 0)
MCA btl: parameter "btl_openib_eager_rdma_num" (current
value: <16>, data source: default value)
Number of RDMA buffers to allocate for small
messages (must be >= 1)
MCA btl: parameter "btl_openib_btls_per_lid" (current
value: <1>, data source: default value)
Number of BTLs to create for each InfiniBand
LID (must be >= 1)
MCA btl: parameter "btl_openib_max_lmc" (current value:
<0>, data source: default value)
Maximum number of LIDs to use for each device
port (must be >= 0, where 0 = use all available)
MCA btl: parameter "btl_openib_enable_apm_over_lmc"
(current value: <0>, data source: default value)
Maximum number of alternative paths for each
device port (must be >= -1, where 0 = disable apm, -1 = all available
alternative
paths )
MCA btl: parameter "btl_openib_enable_apm_over_ports"
(current value: <0>, data source: default value)
Enable alternative path migration (APM) over
different ports of the same device (must be >= 0, where 0 = disable APM
over ports,
1 = enable APM over ports of the same device)
MCA btl: parameter "btl_openib_use_async_event_thread"
(current value: <1>, data source: default value)
If nonzero, use the thread that will handle
InfiniBand asynchronous events
MCA btl: parameter "btl_openib_enable_srq_resize"
(current value: <1>, data source: default value)
Enable/Disable on demand SRQ resize. (0 =
without resizing, nonzero = with resizing)
MCA btl: parameter "btl_openib_buffer_alignment"
(current value: <64>, data source: default value)
Preferred communication buffer alignment, in
bytes (must be > 0 and power of two)
MCA btl: parameter "btl_openib_use_message_coalescing"
(current value: <1>, data source: default value)
If nonzero, use message coalescing
MCA btl: parameter "btl_openib_cq_poll_ratio" (current
value: <100>, data source: default value)
How often to poll high priority CQ versus low
priority CQ
MCA btl: parameter "btl_openib_eager_rdma_poll_ratio"
(current value: <100>, data source: default value)
How often to poll eager RDMA channel versus CQ
MCA btl: parameter "btl_openib_hp_cq_poll_per_progress"
(current value: <10>, data source: default value)
Max number of completion events to process for
each call of BTL progress engine
MCA btl: information "btl_openib_have_fork_support"
(value: <1>, data source: default value)
Whether the OpenFabrics stack supports
applications that invoke the "fork()" system call or not (0 = no, 1 =
yes). Note that this
value does NOT indicate whether the system
being run on supports "fork()" with OpenFabrics applications or not.
MCA btl: parameter "btl_openib_exclusivity" (current
value: <1024>, data source: default value)
BTL exclusivity (must be >= 0)
MCA btl: parameter "btl_openib_flags" (current value:
<310>, data source: default value)
BTL bit flags (general flags: SEND=1, PUT=2,
GET=4, SEND_INPLACE=8, RDMA_MATCHED=64, HETEROGENEOUS_RDMA=256; flags
only used by
the "dr" PML (ignored by others): ACK=16,
CHECKSUM=32, RDMA_COMPLETION=128; flags only used by the "bfo" PML
(ignored by others):
FAILOVER_SUPPORT=512)
MCA btl: parameter "btl_openib_rndv_eager_limit"
(current value: <12288>, data source: default value)
Size (in bytes) of "phase 1" fragment sent for
all large messages (must be >= 0 and <= eager_limit)
MCA btl: parameter "btl_openib_eager_limit" (current
value: <12288>, data source: default value)
Maximum size (in bytes) of "short" messages
(must be >= 1).
MCA btl: parameter "btl_openib_max_send_size" (current
value: <65536>, data source: default value)
Maximum size (in bytes) of a single "phase 2"
fragment of a long message when using the pipeline protocol (must be >= 1)
MCA btl: parameter
"btl_openib_rdma_pipeline_send_length" (current value: <1048576>, data
source: default value)
Length of the "phase 2" portion of a large
message (in bytes) when using the pipeline protocol. This part of the
message will be
split into fragments of size max_send_size and
sent using send/receive semantics (must be >= 0; only relevant when the
PUT flag
is set)
MCA btl: parameter "btl_openib_rdma_pipeline_frag_size"
(current value: <1048576>, data source: default value)
Maximum size (in bytes) of a single "phase 3"
fragment from a long message when using the pipeline protocol. These
fragments
will be sent using RDMA semantics (must be >=
1; only relevant when the PUT flag is set)
MCA btl: parameter "btl_openib_min_rdma_pipeline_size"
(current value: <262144>, data source: default value)
Messages smaller than this size (in bytes)
will not use the RDMA pipeline protocol. Instead, they will be split
into fragments
of max_send_size and sent using send/receive
semantics (must be >=0, and is automatically adjusted up to at least
(eager_limit+btl_rdma_pipeline_send_length);
only relevant when the PUT flag is set)
MCA btl: parameter "btl_openib_bandwidth" (current
value: <0>, data source: default value)
Approximate maximum bandwidth of
interconnect(0 = auto-detect value at run-time [not supported in all BTL
modules], >= 1 =
bandwidth in Mbps)
MCA btl: parameter "btl_openib_latency" (current value:
<4>, data source: default value)
Approximate latency of interconnect (must be >= 0)
MCA btl: parameter "btl_openib_receive_queues" (current
value:
<P,128,256,192,128:S,2048,256,128,32:S,12288,256,128,32:S,65536,256,128,32>,
data source: default value)
Colon-delimited, comma-delimited list of
receive queues: P,4096,8,6,4:P,32768,8,6,4
MCA btl: parameter "btl_openib_if_include" (current
value: <none>, data source: default value)
Comma-delimited list of devices/ports to be
used (e.g. "mthca0,mthca1:2"; empty value means to use all ports
found). Mutually
exclusive with btl_openib_if_exclude.
MCA btl: parameter "btl_openib_if_exclude" (current
value: <none>, data source: default value)
Comma-delimited list of device/ports to be
excluded (empty value means to not exclude any ports). Mutually
exclusive with
btl_openib_if_include.
MCA btl: parameter "btl_openib_ipaddr_include" (current
value: <none>, data source: default value)
Comma-delimited list of IP Addresses to be
used (e.g. "192.168.1.0/24"). Mutually exclusive with
btl_openib_ipaddr_exclude.
MCA btl: parameter "btl_openib_ipaddr_exclude" (current
value: <none>, data source: default value)
Comma-delimited list of IP Addresses to be
excluded (e.g. "192.168.1.0/24"). Mutually exclusive with
btl_openib_ipaddr_include.
MCA btl: parameter "btl_openib_gid_index" (current
value: <0>, data source: default value)
GID index to use on verbs device ports
MCA btl: parameter "btl_openib_cpc_include" (current
value: <none>, data source: default value)
Method used to select OpenFabrics connections
(valid values: oob,xoob,rdmacm)
MCA btl: parameter "btl_openib_cpc_exclude" (current
value: <none>, data source: default value)
Method used to exclude OpenFabrics connections
(valid values: oob,xoob,rdmacm)
MCA btl: parameter "btl_openib_connect_oob_priority"
(current value: <50>, data source: default value)
The selection method priority for oob
MCA btl: parameter "btl_openib_connect_xoob_priority"
(current value: <60>, data source: default value)
The selection method priority for xoob
MCA btl: parameter "btl_openib_connect_rdmacm_priority"
(current value: <30>, data source: default value)
The selection method priority for rdma_cm
MCA btl: parameter "btl_openib_connect_rdmacm_port"
(current value: <0>, data source: default value)
The selection method port for rdma_cm
MCA btl: parameter
"btl_openib_connect_rdmacm_resolve_timeout" (current value: <30000>,
data source: default value)
The timeout (in miliseconds) for address and
route resolution
MCA btl: parameter
"btl_openib_connect_rdmacm_retry_count" (current value: <20>, data
source: default value)
Maximum number of times rdmacm will retry
route resolution
MCA btl: parameter
"btl_openib_connect_rdmacm_reject_causes_connect_error" (current value:
<0>, data source: default value)
The drivers for some devices are buggy such
that an RDMA REJECT action may result in a CONNECT_ERROR event instead
of a REJECTED
event. Setting this MCA parameter to true
tells Open MPI to treat CONNECT_ERROR events on connections where a
REJECT is expected
as a REJECT (default: false)
MCA btl: parameter "btl_openib_priority" (current
value: <0>, data source: default value)
MCA btl: parameter "btl_self_free_list_num" (current
value: <0>, data source: default value)
Number of fragments by default
MCA btl: parameter "btl_self_free_list_max" (current
value: <-1>, data source: default value)
Maximum number of fragments
MCA btl: parameter "btl_self_free_list_inc" (current
value: <32>, data source: default value)
Increment by this number of fragments
MCA btl: parameter "btl_self_exclusivity" (current
value: <65536>, data source: default value)
BTL exclusivity (must be >= 0)
MCA btl: parameter "btl_self_flags" (current value:
<10>, data source: default value)
BTL bit flags (general flags: SEND=1, PUT=2,
GET=4, SEND_INPLACE=8, RDMA_MATCHED=64, HETEROGENEOUS_RDMA=256; flags
only used by
the "dr" PML (ignored by others): ACK=16,
CHECKSUM=32, RDMA_COMPLETION=128; flags only used by the "bfo" PML
(ignored by others):
FAILOVER_SUPPORT=512)
MCA btl: parameter "btl_self_rndv_eager_limit" (current
value: <131072>, data source: default value)
Size (in bytes) of "phase 1" fragment sent for
all large messages (must be >= 0 and <= eager_limit)
MCA btl: parameter "btl_self_eager_limit" (current
value: <131072>, data source: default value)
Maximum size (in bytes) of "short" messages
(must be >= 1).
MCA btl: parameter "btl_self_max_send_size" (current
value: <262144>, data source: default value)
Maximum size (in bytes) of a single "phase 2"
fragment of a long message when using the pipeline protocol (must be >= 1)
MCA btl: parameter "btl_self_rdma_pipeline_send_length"
(current value: <2147483647>, data source: default value)
Length of the "phase 2" portion of a large
message (in bytes) when using the pipeline protocol. This part of the
message will be
split into fragments of size max_send_size and
sent using send/receive semantics (must be >= 0; only relevant when the
PUT flag
is set)
MCA btl: parameter "btl_self_rdma_pipeline_frag_size"
(current value: <2147483647>, data source: default value)
Maximum size (in bytes) of a single "phase 3"
fragment from a long message when using the pipeline protocol. These
fragments
will be sent using RDMA semantics (must be >=
1; only relevant when the PUT flag is set)
MCA btl: parameter "btl_self_min_rdma_pipeline_size"
(current value: <0>, data source: default value)
Messages smaller than this size (in bytes)
will not use the RDMA pipeline protocol. Instead, they will be split
into fragments
of max_send_size and sent using send/receive
semantics (must be >=0, and is automatically adjusted up to at least
(eager_limit+btl_rdma_pipeline_send_length);
only relevant when the PUT flag is set)
MCA btl: parameter "btl_self_bandwidth" (current value:
<100>, data source: default value)
Approximate maximum bandwidth of
interconnect(0 = auto-detect value at run-time [not supported in all BTL
modules], >= 1 =
bandwidth in Mbps)
MCA btl: parameter "btl_self_latency" (current value:
<0>, data source: default value)
Approximate latency of interconnect (must be >= 0)
MCA btl: parameter "btl_self_priority" (current value:
<0>, data source: default value)
MCA btl: information "btl_sm_have_knem_support" (value:
<0>, data source: default value)
Whether this component supports the knem Linux
kernel module or not
MCA btl: parameter "btl_sm_use_knem" (current value:
<0>, data source: default value)
Whether knem support is desired or not
(negative = try to enable knem support, but continue even if it is not
available, 0 = do
not enable knem support, positive = try to
enable knem support and fail if it is not available)
MCA btl: parameter "btl_sm_knem_dma_min" (current
value: <0>, data source: default value)
Minimum message size (in bytes) to use the
knem DMA mode; ignored if knem does not support DMA mode (0 = do not use
the knem DMA
mode)
MCA btl: parameter "btl_sm_knem_max_simultaneous"
(current value: <0>, data source: default value)
Max number of simultaneous ongoing knem
operations to support (0 = do everything synchronously, which probably
gives the best
large message latency; >0 means to do all
operations asynchronously, which supports better overlap for
simultaneous large message
sends)
MCA btl: parameter "btl_sm_free_list_num" (current
value: <8>, data source: default value)
MCA btl: parameter "btl_sm_free_list_max" (current
value: <-1>, data source: default value)
MCA btl: parameter "btl_sm_free_list_inc" (current
value: <64>, data source: default value)
MCA btl: parameter "btl_sm_max_procs" (current value:
<-1>, data source: default value)
MCA btl: parameter "btl_sm_mpool" (current value: <sm>,
data source: default value)
MCA btl: parameter "btl_sm_fifo_size" (current value:
<4096>, data source: default value)
MCA btl: parameter "btl_sm_num_fifos" (current value:
<1>, data source: default value)
MCA btl: parameter "btl_sm_fifo_lazy_free" (current
value: <120>, data source: default value)
MCA btl: parameter "btl_sm_sm_extra_procs" (current
value: <0>, data source: default value)
MCA btl: parameter "btl_sm_exclusivity" (current value:
<65535>, data source: default value)
BTL exclusivity (must be >= 0)
MCA btl: parameter "btl_sm_flags" (current value: <1>,
data source: default value)
BTL bit flags (general flags: SEND=1, PUT=2,
GET=4, SEND_INPLACE=8, RDMA_MATCHED=64, HETEROGENEOUS_RDMA=256; flags
only used by
the "dr" PML (ignored by others): ACK=16,
CHECKSUM=32, RDMA_COMPLETION=128; flags only used by the "bfo" PML
(ignored by others):
FAILOVER_SUPPORT=512)
MCA btl: parameter "btl_sm_rndv_eager_limit" (current
value: <4096>, data source: default value)
Size (in bytes) of "phase 1" fragment sent for
all large messages (must be >= 0 and <= eager_limit)
MCA btl: parameter "btl_sm_eager_limit" (current value:
<4096>, data source: default value)
Maximum size (in bytes) of "short" messages
(must be >= 1).
MCA btl: parameter "btl_sm_max_send_size" (current
value: <32768>, data source: default value)
Maximum size (in bytes) of a single "phase 2"
fragment of a long message when using the pipeline protocol (must be >= 1)
MCA btl: parameter "btl_sm_bandwidth" (current value:
<9000>, data source: default value)
Approximate maximum bandwidth of
interconnect(0 = auto-detect value at run-time [not supported in all BTL
modules], >= 1 =
bandwidth in Mbps)
MCA btl: parameter "btl_sm_latency" (current value:
<1>, data source: default value)
Approximate latency of interconnect (must be >= 0)
MCA btl: parameter "btl_sm_priority" (current value:
<0>, data source: default value)
MCA btl: parameter "btl_tcp_links" (current value: <1>,
data source: default value)
MCA btl: parameter "btl_tcp_if_include" (current value:
<none>, data source: default value)
Comma-delimited list of devices or CIDR
notation of networks to use for MPI communication (e.g., "eth0,eth1" or
"192.168.0.0/16,10.1.4.0/24"). Mutually
exclusive with btl_tcp_if_exclude.
MCA btl: parameter "btl_tcp_if_exclude" (current value:
<lo,sppp>, data source: default value)
Comma-delimited list of devices or CIDR
notation of networks to NOT use for MPI communication -- all devices not
matching these
specifications will be used (e.g., "eth0,eth1"
or "192.168.0.0/16,10.1.4.0/24"). Mutually exclusive with
btl_tcp_if_include.
MCA btl: parameter "btl_tcp_free_list_num" (current
value: <8>, data source: default value)
MCA btl: parameter "btl_tcp_free_list_max" (current
value: <-1>, data source: default value)
MCA btl: parameter "btl_tcp_free_list_inc" (current
value: <32>, data source: default value)
MCA btl: parameter "btl_tcp_sndbuf" (current value:
<131072>, data source: default value)
MCA btl: parameter "btl_tcp_rcvbuf" (current value:
<131072>, data source: default value)
MCA btl: parameter "btl_tcp_endpoint_cache" (current
value: <30720>, data source: default value)
The size of the internal cache for each TCP
connection. This cache is used to reduce the number of syscalls, by
replacing them
with memcpy. Every read will read the expected
data plus the amount of the endpoint_cache
MCA btl: parameter "btl_tcp_use_nagle" (current value:
<0>, data source: default value)
Whether to use Nagle's algorithm or not (using
Nagle's algorithm may increase short message latency)
MCA btl: parameter "btl_tcp_port_min_v4" (current
value: <1024>, data source: default value)
The minimum port where the TCP BTL will try to
bind (default 1024)
MCA btl: parameter "btl_tcp_port_range_v4" (current
value: <64511>, data source: default value)
The number of ports where the TCP BTL will try
to bind (default 64511). This parameter together with the port min,
define a range
of ports where Open MPI will open sockets.
MCA btl: parameter "btl_tcp_exclusivity" (current
value: <100>, data source: default value)
BTL exclusivity (must be >= 0)
MCA btl: parameter "btl_tcp_flags" (current value:
<314>, data source: default value)
BTL bit flags (general flags: SEND=1, PUT=2,
GET=4, SEND_INPLACE=8, RDMA_MATCHED=64, HETEROGENEOUS_RDMA=256; flags
only used by
the "dr" PML (ignored by others): ACK=16,
CHECKSUM=32, RDMA_COMPLETION=128; flags only used by the "bfo" PML
(ignored by others):
FAILOVER_SUPPORT=512)
MCA btl: parameter "btl_tcp_rndv_eager_limit" (current
value: <65536>, data source: default value)
Size (in bytes) of "phase 1" fragment sent for
all large messages (must be >= 0 and <= eager_limit)
MCA btl: parameter "btl_tcp_eager_limit" (current
value: <65536>, data source: default value)
Maximum size (in bytes) of "short" messages
(must be >= 1).
MCA btl: parameter "btl_tcp_max_send_size" (current
value: <131072>, data source: default value)
Maximum size (in bytes) of a single "phase 2"
fragment of a long message when using the pipeline protocol (must be >= 1)
MCA btl: parameter "btl_tcp_rdma_pipeline_send_length"
(current value: <131072>, data source: default value)
Length of the "phase 2" portion of a large
message (in bytes) when using the pipeline protocol. This part of the
message will be
split into fragments of size max_send_size and
sent using send/receive semantics (must be >= 0; only relevant when the
PUT flag
is set)
MCA btl: parameter "btl_tcp_rdma_pipeline_frag_size"
(current value: <2147483647>, data source: default value)
Maximum size (in bytes) of a single "phase 3"
fragment from a long message when using the pipeline protocol. These
fragments
will be sent using RDMA semantics (must be >=
1; only relevant when the PUT flag is set)
MCA btl: parameter "btl_tcp_min_rdma_pipeline_size"
(current value: <0>, data source: default value)
Messages smaller than this size (in bytes)
will not use the RDMA pipeline protocol. Instead, they will be split
into fragments
of max_send_size and sent using send/receive
semantics (must be >=0, and is automatically adjusted up to at least
(eager_limit+btl_rdma_pipeline_send_length);
only relevant when the PUT flag is set)
MCA btl: parameter "btl_tcp_bandwidth" (current value:
<100>, data source: default value)
Approximate maximum bandwidth of
interconnect(0 = auto-detect value at run-time [not supported in all BTL
modules], >= 1 =
bandwidth in Mbps)
MCA btl: parameter "btl_tcp_latency" (current value:
<100>, data source: default value)
Approximate latency of interconnect (must be >= 0)
MCA btl: parameter "btl_tcp_disable_family" (current
value: <0>, data source: default value)
MCA btl: parameter "btl_tcp_if_seq" (current value:
<none>, data source: default value)
If specified, a comma-delimited list of TCP
interfaces. Interfaces will be assigned, one to each MPI process, in a
round-robin
fashion on each server. For example, if the
list is "eth0,eth1" and four MPI processes are run on a single server,
then local
ranks 0 and 2 will use eth0 and local ranks 1
and 3 will use eth1.
MCA btl: parameter "btl_tcp_priority" (current value:
<0>, data source: default value)
MCA btl: parameter "btl_base_include" (current value:
<none>, data source: default value)
MCA btl: parameter "btl_base_exclude" (current value:
<none>, data source: default value)
MCA btl: parameter "btl_base_warn_component_unused"
(current value: <1>, data source: default value)
This parameter is used to turn on warning
messages when certain NICs are not used
MCA mtl: parameter "mtl" (current value: <none>, data
source: default value)
Default selection set of components for the
mtl framework (<none> means use all components that can be found)
MCA mtl: parameter "mtl_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the mtl framework (0 = no
verbosity)
MCA topo: parameter "topo" (current value: <none>, data
source: default value)
Default selection set of components for the
topo framework (<none> means use all components that can be found)
MCA topo: parameter "topo_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the topo framework (0 = no
verbosity)
MCA topo: parameter "topo_unity_priority" (current
value: <0>, data source: default value)
MCA osc: parameter "osc" (current value: <none>, data
source: default value)
Default selection set of components for the
osc framework (<none> means use all components that can be found)
MCA osc: parameter "osc_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the osc framework (0 = no
verbosity)
MCA osc: parameter "osc_pt2pt_no_locks" (current value:
<0>, data source: default value)
Enable optimizations available only if
MPI_LOCK is not used.
MCA osc: parameter "osc_pt2pt_eager_limit" (current
value: <16384>, data source: default value)
Max size of eagerly sent data
MCA osc: parameter "osc_pt2pt_priority" (current value:
<0>, data source: default value)
MCA osc: parameter "osc_rdma_eager_send" (current
value: <1>, data source: default value)
Attempt to start data movement during
communication call, instead of at synchrnoization time. Info key of
same name overrides
this value.
MCA osc: parameter "osc_rdma_use_buffers" (current
value: <1>, data source: default value)
Coalesce messages during an epoch to reduce
network utilization. Info key of same name overrides this value.
MCA osc: parameter "osc_rdma_use_rdma" (current value:
<0>, data source: default value)
Use real RDMA operations to transfer data.
Info key of same name overrides this value.
MCA osc: parameter "osc_rdma_rdma_completion_wait"
(current value: <1>, data source: default value)
Wait for all completion of rdma events before
sending acknowledgment. Info key of same name overrides this value.
MCA osc: parameter "osc_rdma_no_locks" (current value:
<0>, data source: default value)
Enable optimizations available only if
MPI_LOCK is not used. Info key of same name overrides this value.
MCA osc: parameter "osc_rdma_priority" (current value:
<0>, data source: default value)
MCA op: parameter "op_base_verbose" (current value:
<0>, data source: default value)
Verbosity level of the op framework
MCA iof: parameter "iof" (current value: <none>, data
source: default value)
Default selection set of components for the
iof framework (<none> means use all components that can be found)
MCA iof: parameter "iof_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the iof framework (0 = no
verbosity)
MCA iof: parameter "iof_hnp_priority" (current value:
<0>, data source: default value)
MCA iof: parameter "iof_orted_priority" (current value:
<0>, data source: default value)
MCA iof: parameter "iof_tool_priority" (current value:
<0>, data source: default value)
MCA oob: parameter "oob" (current value: <none>, data
source: default value)
Default selection set of components for the
oob framework (<none> means use all components that can be found)
MCA oob: parameter "oob_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the oob framework (0 = no
verbosity)
MCA oob: parameter "oob_tcp_verbose" (current value:
<0>, data source: default value)
Verbose level for the OOB tcp component
MCA oob: parameter "oob_tcp_peer_limit" (current value:
<-1>, data source: default value)
Maximum number of peer connections to
simultaneously maintain (-1 = infinite)
MCA oob: parameter "oob_tcp_peer_retries" (current
value: <60>, data source: default value)
Number of times to try shutting down a
connection before giving up
MCA oob: parameter "oob_tcp_debug" (current value: <0>,
data source: default value)
Enable (1) / disable (0) debugging output for
this component
MCA oob: parameter "oob_tcp_sndbuf" (current value:
<131072>, data source: default value)
TCP socket send buffering size (in bytes)
MCA oob: parameter "oob_tcp_rcvbuf" (current value:
<131072>, data source: default value)
TCP socket receive buffering size (in bytes)
MCA oob: parameter "oob_tcp_if_include" (current value:
<none>, data source: default value)
Comma-delimited list of TCP interfaces to use
MCA oob: parameter "oob_tcp_if_exclude" (current value:
<none>, data source: default value)
Comma-delimited list of TCP interfaces to exclude
MCA oob: parameter "oob_tcp_connect_sleep" (current
value: <1>, data source: default value)
Enable (1) / disable (0) random sleep for
connection wireup.
MCA oob: parameter "oob_tcp_listen_mode" (current
value: <event>, data source: default value)
Mode for HNP to accept incoming connections:
event, listen_thread.
MCA oob: parameter "oob_tcp_listen_thread_max_queue"
(current value: <10>, data source: default value)
High water mark for queued accepted socket
list size. Used only when listen_mode is listen_thread.
MCA oob: parameter "oob_tcp_listen_thread_wait_time"
(current value: <10>, data source: default value)
Time in milliseconds to wait before actively
checking for new connections when listen_mode is listen_thread.
MCA oob: parameter "oob_tcp_static_ports" (current
value: <none>, data source: default value)
Static ports for daemons and procs (IPv4)
MCA oob: parameter "oob_tcp_dynamic_ports" (current
value: <none>, data source: default value)
Range of ports to be dynamically used by
daemons and procs (IPv4)
MCA oob: parameter "oob_tcp_disable_family" (current
value: <0>, data source: default value)
Disable IPv4 (4) or IPv6 (6)
MCA oob: parameter "oob_tcp_priority" (current value:
<0>, data source: default value)
MCA odls: parameter "odls_base_sigkill_timeout" (current
value: <1>, data source: default value)
Time to wait for a process to die after
issuing a kill signal to it
MCA odls: parameter "odls" (current value: <none>, data
source: default value)
Default selection set of components for the
odls framework (<none> means use all components that can be found)
MCA odls: parameter "odls_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the odls framework (0 = no
verbosity)
MCA odls: parameter "odls_default_priority" (current
value: <0>, data source: default value)
MCA ras: parameter "ras_base_display_alloc" (current
value: <0>, data source: default value)
Whether to display the allocation after it is
determined
MCA ras: parameter "ras_base_display_devel_alloc"
(current value: <0>, data source: default value)
Whether to display a developer-detail
allocation after it is determined
MCA ras: parameter "ras" (current value: <none>, data
source: default value)
Default selection set of components for the
ras framework (<none> means use all components that can be found)
MCA ras: parameter "ras_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the ras framework (0 = no
verbosity)
MCA ras: parameter "ras_cm_priority" (current value:
<0>, data source: default value)
MCA ras: parameter "ras_loadleveler_priority" (current
value: <90>, data source: default value)
Priority of the loadleveler ras component
MCA ras: parameter "ras_slurm_priority" (current value:
<75>, data source: default value)
Priority of the slurm ras component
MCA ras: parameter "ras_tm_priority" (current value:
<100>, data source: default value)
Priority of the tm ras component
MCA ras: parameter "ras_tm_nodefile_dir" (current
value: </var/torque/aux>, data source: default value)
The directory where the PBS nodefile can be found
MCA rmaps: parameter "rmaps_rank_file_path" (current
value: <none>, data source: default value, synonym of: orte_rankfile)
Name of the rankfile to be used for mapping
processes (relative or absolute path)
MCA rmaps: parameter "rmaps_base_schedule_policy"
(current value: <slot>, data source: default value)
Scheduling Policy for RMAPS. [slot
(alias:core) | socket | board | node]
MCA rmaps: parameter "rmaps_base_pernode" (current value:
<0>, data source: default value)
Launch one ppn as directed
MCA rmaps: parameter "rmaps_base_n_pernode" (current
value: <-1>, data source: default value)
Launch n procs/node
MCA rmaps: parameter "rmaps_base_n_perboard" (current
value: <-1>, data source: default value)
Launch n procs/board
MCA rmaps: parameter "rmaps_base_n_persocket" (current
value: <-1>, data source: default value)
Launch n procs/socket
MCA rmaps: parameter "rmaps_base_loadbalance" (current
value: <0>, data source: default value)
Balance total number of procs across all
allocated nodes
MCA rmaps: parameter "rmaps_base_cpus_per_proc" (current
value: <1>, data source: default value, synonyms: rmaps_base_cpus_per_rank)
Number of cpus to use for each rank [1-2**15
(default=1)]
MCA rmaps: parameter "rmaps_base_cpus_per_rank" (current
value: <1>, data source: default value, synonym of:
rmaps_base_cpus_per_proc)
Number of cpus to use for each rank [1-2**15
(default=1)]
MCA rmaps: parameter "rmaps_base_stride" (current value:
<1>, data source: default value)
When binding multiple cores to a rank, the
step size to use between cores [1-2**15 (default: 1)]
MCA rmaps: parameter "rmaps_base_slot_list" (current
value: <none>, data source: default value)
List of processor IDs to bind MPI processes to
(e.g., used in conjunction with rank files) [default=NULL]
MCA rmaps: parameter "rmaps_base_no_schedule_local"
(current value: <0>, data source: default value)
If false, allow scheduling MPI applications on
the same node as mpirun (default). If true, do not schedule any MPI
applications
on the same node as mpirun
MCA rmaps: parameter "rmaps_base_no_oversubscribe"
(current value: <0>, data source: default value)
If true, then do not allow oversubscription of
nodes - mpirun will return an error if there aren't enough nodes to
launch all
processes without oversubscribing
MCA rmaps: parameter "rmaps_base_display_map" (current
value: <0>, data source: default value)
Whether to display the process map after it is
computed
MCA rmaps: parameter "rmaps_base_display_devel_map"
(current value: <0>, data source: default value)
Whether to display a developer-detail process
map after it is computed
MCA rmaps: parameter "rmaps" (current value: <none>, data
source: default value)
Default selection set of components for the
rmaps framework (<none> means use all components that can be found)
MCA rmaps: parameter "rmaps_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the rmaps framework (0 =
no verbosity)
MCA rmaps: parameter "rmaps_load_balance_priority"
(current value: <0>, data source: default value)
MCA rmaps: parameter "rmaps_rank_file_priority" (current
value: <0>, data source: default value)
MCA rmaps: parameter "rmaps_resilient_fault_grp_file"
(current value: <none>, data source: default value)
Filename that contains a description of fault
groups for this system
MCA rmaps: parameter "rmaps_resilient_priority" (current
value: <0>, data source: default value)
MCA rmaps: parameter "rmaps_round_robin_priority"
(current value: <0>, data source: default value)
MCA rmaps: parameter "rmaps_seq_priority" (current value:
<0>, data source: default value)
MCA rmaps: parameter "rmaps_topo_priority" (current
value: <0>, data source: default value)
MCA rml: parameter "rml_wrapper" (current value:
<none>, data source: default value)
Use a Wrapper component around the selected
RML component
MCA rml: parameter "rml" (current value: <none>, data
source: default value)
Default selection set of components for the
rml framework (<none> means use all components that can be found)
MCA rml: parameter "rml_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the rml framework (0 = no
verbosity)
MCA rml: parameter "rml_oob_priority" (current value:
<0>, data source: default value)
MCA routed: parameter "routed" (current value: <none>,
data source: default value)
Default selection set of components for the
routed framework (<none> means use all components that can be found)
MCA routed: parameter "routed_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the routed framework (0 =
no verbosity)
MCA routed: parameter "routed_binomial_priority" (current
value: <0>, data source: default value)
MCA routed: parameter "routed_cm_priority" (current value:
<0>, data source: default value)
MCA routed: parameter "routed_direct_priority" (current
value: <0>, data source: default value)
MCA routed: parameter "routed_linear_priority" (current
value: <0>, data source: default value)
MCA routed: parameter "routed_radix_priority" (current
value: <0>, data source: default value)
MCA routed: parameter "routed_slave_priority" (current
value: <0>, data source: default value)
MCA plm: parameter "plm_rsh_agent" (current value: <ssh
: rsh>, data source: default value, deprecated, synonym of: orte_rsh_agent)
The command used to launch executables on
remote nodes (typically either "ssh" or "rsh")
MCA plm: parameter "plm_rsh_assume_same_shell" (current
value: <1>, data source: default value, deprecated, synonym of:
orte_assume_same_shell)
If set to 1, assume that the shell on the
remote node is the same as the shell on the local node. Otherwise,
probe for what the
remote shell [default: 1]
MCA plm: parameter "plm" (current value: <none>, data
source: default value)
Default selection set of components for the
plm framework (<none> means use all components that can be found)
MCA plm: parameter "plm_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the plm framework (0 = no
verbosity)
MCA plm: parameter "plm_rsh_num_concurrent" (current
value: <128>, data source: default value)
How many plm_rsh_agent instances to invoke
concurrently (must be > 0)
MCA plm: parameter "plm_rsh_force_rsh" (current value:
<0>, data source: default value)
Force the launcher to always use rsh
MCA plm: parameter "plm_rsh_disable_qrsh" (current
value: <0>, data source: default value)
Disable the launcher to use qrsh when under
the SGE parallel environment
MCA plm: parameter "plm_rsh_daemonize_qrsh" (current
value: <0>, data source: default value)
Daemonize the orted under the SGE parallel
environment
MCA plm: parameter "plm_rsh_disable_llspawn" (current
value: <0>, data source: default value)
Disable the use of llspawn when under the
LoadLeveler environment
MCA plm: parameter "plm_rsh_daemonize_llspawn" (current
value: <0>, data source: default value)
Daemonize the orted when under the LoadLeveler
environment
MCA plm: parameter "plm_rsh_priority" (current value:
<10>, data source: default value)
Priority of the rsh plm component
MCA plm: parameter "plm_rsh_delay" (current value: <1>,
data source: default value)
Delay (in seconds) between invocations of the
remote agent, but only used when the "debug" MCA parameter is true, or the
top-level MCA debugging is enabled (otherwise
this value is ignored)
MCA plm: parameter "plm_rsh_tree_spawn" (current value:
<0>, data source: default value)
If set to 1, launch via a tree-based topology
MCA plm: parameter "plm_slurm_args" (current value:
<none>, data source: default value)
Custom arguments to srun
MCA plm: parameter "plm_slurm_priority" (current value:
<0>, data source: default value)
MCA plm: parameter "plm_tm_want_path_check" (current
value: <1>, data source: default value)
Whether the launching process should check for
the plm_tm_orted executable in the PATH before launching (the TM API
does not give
an indication of failure; this is a
somewhat-lame workaround; non-zero values enable this check)
MCA plm: parameter "plm_tm_priority" (current value:
<0>, data source: default value)
MCA filem: parameter "filem" (current value: <none>, data
source: default value)
Which Filem component to use (empty = auto-select)
MCA filem: parameter "filem_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the filem framework (0 =
no verbosity)
MCA filem: parameter "filem_rsh_priority" (current value:
<20>, data source: default value)
Priority of the FILEM rsh component
MCA filem: parameter "filem_rsh_verbose" (current value:
<0>, data source: default value)
Verbose level for the FILEM rsh component
MCA filem: parameter "filem_rsh_rcp" (current value:
<scp>, data source: default value)
The rsh cp command for the FILEM rsh component
MCA filem: parameter "filem_rsh_cp" (current value: <cp>,
data source: default value)
The Unix cp command for the FILEM rsh component
MCA filem: parameter "filem_rsh_rsh" (current value:
<ssh>, data source: default value)
The remote shell command for the FILEM rsh
component
MCA filem: parameter "filem_rsh_max_incomming" (current
value: <10>, data source: default value)
Maximum number of incomming connections (0 = any)
MCA filem: parameter "filem_rsh_max_outgoing" (current
value: <10>, data source: default value)
Maximum number of out going connections (0 = any)
MCA errmgr: parameter "errmgr" (current value: <none>,
data source: default value)
Default selection set of components for the
errmgr framework (<none> means use all components that can be found)
MCA errmgr: parameter "errmgr_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the errmgr framework (0 =
no verbosity)
MCA errmgr: parameter "errmgr_default_priority" (current
value: <0>, data source: default value)
MCA ess: parameter "ess" (current value: <none>, data
source: default value)
Default selection set of components for the
ess framework (<none> means use all components that can be found)
MCA ess: parameter "ess_base_verbose" (current value:
<0>, data source: default value)
Verbosity level for the ess framework (0 = no
verbosity)
MCA ess: parameter "ess_env_priority" (current value:
<0>, data source: default value)
MCA ess: parameter "ess_hnp_priority" (current value:
<0>, data source: default value)
MCA ess: parameter "ess_singleton_priority" (current
value: <0>, data source: default value)
MCA ess: parameter "ess_slave_priority" (current value:
<0>, data source: default value)
MCA ess: parameter "ess_slurm_priority" (current value:
<0>, data source: default value)
MCA ess: parameter "ess_slurmd_priority" (current
value: <0>, data source: default value)
MCA ess: parameter "ess_tm_priority" (current value:
<0>, data source: default value)
MCA ess: parameter "ess_tool_priority" (current value:
<0>, data source: default value)
MCA grpcomm: parameter "grpcomm" (current value: <none>,
data source: default value)
Default selection set of components for the
grpcomm framework (<none> means use all components that can be found)
MCA grpcomm: parameter "grpcomm_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the grpcomm framework (0 =
no verbosity)
MCA grpcomm: parameter "grpcomm_bad_priority" (current
value: <0>, data source: default value)
MCA grpcomm: parameter "grpcomm_basic_priority" (current
value: <0>, data source: default value)
MCA grpcomm: parameter "grpcomm_hier_priority" (current
value: <0>, data source: default value)
MCA notifier: parameter "notifier_threshold_severity"
(current value: <critical>, data source: default value)
Report all events at or above this severity
[default: critical]
MCA notifier: parameter "notifier" (current value: <none>,
data source: default value)
Default selection set of components for the
notifier framework (<none> means use all components that can be found)
MCA notifier: parameter "notifier_base_verbose" (current
value: <0>, data source: default value)
Verbosity level for the notifier framework (0
= no verbosity)
MCA notifier: parameter "notifier_command_cmd" (current
value: </sbin/initlog -f $s -n "Open MPI" -s "$S: $m (errorcode: $e)">,
data source:
default value)
Command to execute, with substitution. $s =
integer severity; $S = string severity; $e = integer error code; $m =
string message
MCA notifier: parameter "notifier_command_timeout" (current
value: <30>, data source: default value)
Timeout (in seconds) of the command
MCA notifier: parameter "notifier_command_priority" (current
value: <10>, data source: default value)
Priority of this component
MCA notifier: parameter "notifier_syslog_priority" (current
value: <0>, data source: default value)
-------
echo $PATH
/home/apps/Logiciels/MPI/intel/openmpi/1.6/bin:/home/apps/intel/composerxe-2011.4.191/bin/intel64:/opt/torque/x86_64/bin:/tmp:/xcatpost:/sbin:/usr/sbin:/bin:/usr/bin
echo $LD_LIBRARY_PATH
/home/apps/Logiciels/MPI/intel/openmpi/1.6/lib:/opt/torque/x86_64/lib/:/home/apps/intel/composerxe-2011.4.191/tbb/lib/intel64/cc4.1.0_libc2.4_kernel2.6.16.21:/home/apps/intel/composerxe-2011.4.191/mkl/../compiler/lib/intel64:/home/apps/intel/composerxe-2011.4.191/mkl/lib/intel64:/home/apps/intel/composerxe-2011.4.191/compiler/lib/intel64
------
Thanks,
François
