Hi Robert, I placed a call from 2.3 to 2.5(gail) to observe the traffic. Then I place a call from 2.3 to [EMAIL PROTECTED] to observe the traffic through openser.
For the network topology, it's all on the same local network. I tried the default cfg file and it works fine. I'll try adjusting nat_uac_test, as it's not recognizing I'm on the local network. All set, Thanks! -----Original Message----- From: Robert Dyck Sent: Thursday, February 14, 2008 9:49 PM To: [email protected] Cc: Eric Phetteplace Subject: Re: [OpenSER-Users] OpenSerand RTPProxy, no RTP audio The pro's seem to be busy so I'll give it a go. If gail == 2.5 then a call from 2.5 to gail does not make much sense but maybe it was a typo. You did not say anything about your topology. Where were expecting to find the RTP packets? uac test 19 ( really 16+2+1 ) maybe isn't really what you want. Check the nathelper documentation. Among other things it will check for a private address. If you have local to local calls, there is no NAT involved. Sending the RTP through a proxy is unnecessary. It probably would work though. On Thursday 14 February 2008, Eric Phetteplace wrote: > Hello, > > Following > http://www.voip-info.org/wiki/index.php?page=OpenSER%20v1.2.x%20and%20RTPPr >o xy and cleaning up the errors in the log, I have OpenSER 1.3 and RTPProxy > running in my local domain (192.168.2.10) > > I have two SIP phones in my local domain, on two machines. (2.5 and 2.3) > > I added an alias via openserctl ul add gail sip:192.168.2.5 > > Looking at the packets captured from a call between 2.5 and 2.3, 2.3 should > start streaming RTP packets after it ACKs the 200 from 2.5 > > I call from 192.168.2.5 to [EMAIL PROTECTED] and the connection is > established between the three, but no RTP streams ever begin. I expected > to see 2.3 streaming RTP after it ACKs the 200 from 2.10. > > Any suggestions? > > Here's my cfg file: > > # > # sample config file to be used with nathelper/rtpproxy > # > # start RTPProxy with: rtpproxy -l your_public_ip -s udp:localhost:8899 > # > > # ----------- global configuration parameters ------------------------ > > debug=3 # debug level (cmd line: -dddddddddd) > fork=yes > log_stderror=no # (cmd line: -E) > > /* Uncomment these lines to enter debugging mode > fork=no > log_stderror=yes > */ > > check_via=no # (cmd. line: -v) > dns=no # (cmd. line: -r) > rev_dns=no # (cmd. line: -R) > port=5060 > children=4 > > # --- module loading > > mpath="/usr/local/lib/openser/modules/" > > loadmodule "mysql.so" > loadmodule "sl.so" > loadmodule "tm.so" > loadmodule "rr.so" > loadmodule "maxfwd.so" > loadmodule "usrloc.so" > loadmodule "textops.so" > loadmodule "auth.so" > loadmodule "auth_db.so" > loadmodule "xlog.so" > loadmodule "registrar.so" > loadmodule "mi_fifo.so" > loadmodule "presence.so" > loadmodule "presence_xml.so" > loadmodule "xcap_client.so" > loadmodule "nathelper.so" > > # --- setting module parameters > > modparam("mi_fifo", "fifo_name", "/tmp/openser_fifo") > > modparam("auth_db","db_url","mysql://openser:[EMAIL PROTECTED]/openser") > > modparam("registrar", "received_avp", "$avp(s:rcv)") > > modparam("xcap_client", "db_url", > "mysql://openser:[EMAIL PROTECTED]/openser") > > # -- usrloc params -- > modparam("usrloc", "db_url", "mysql://openser:[EMAIL PROTECTED]/openser") > modparam("usrloc", "db_mode", 2) > modparam("usrloc", "nat_bflag", 3) > > # -- registrar params -- > modparam("registrar", "received_avp", "$avp(s:rcv)") > > # -- auth params -- > modparam("auth_db", "calculate_ha1", yes) > modparam("auth_db", "password_column", "password") > > # -- rr params -- > modparam("rr", "enable_full_lr", 1) > > # -- nathelper > modparam("nathelper", "rtpproxy_sock", "udp:127.0.0.1:8899") > modparam("nathelper", "natping_interval", 30) > modparam("nathelper", "ping_nated_only", 1) > #modparam("nathelper", "sipping_bflag", 7) > modparam("nathelper", "sipping_from", "sip:[EMAIL PROTECTED]") > modparam("nathelper", "received_avp", "$avp(s:rcv)") > > # -- xlog > modparam("xlog", "buf_size", 8192) > > # -- presence params -- > modparam("presence|presence_xml|usrloc", "db_url", > "mysql://openser:[EMAIL PROTECTED]/openser") > modparam("presence", "max_expires", 3600) > modparam("presence_xml", "force_active", 1) > modparam("presence", "server_address", "sip:127.0.0.1:5060" ) > > > # --- main routing logic > route{ > xlog("***start***\n"); > if (!mf_process_maxfwd_header("10")) { > sl_send_reply("483","Too Many Hops"); > xlog("***end - Too Many Hops"); > exit; > }; > if (msg:len >= 2048 ) { > sl_send_reply("513", "Message too big"); > xlog("***end - Too big"); > exit; > }; > > # NAT detection > route(2); > > if (!method=="REGISTER") { > xlog("***route - recordroute\n"); > record_route(); > } > if (loose_route()) { > xlog("***route - looseroute\n"); > append_hf("P-hint: rr-enforced\r\n"); > route(1); > }; > > if (!uri==myself) { > xlog("***route - not myself\n"); > append_hf("P-hint: outbound\r\n"); > route(1); > }; > > if (uri==myself) { > if (method=="REGISTER") { > xlog("***route - register"); > if (!www_authorize("openser.org", "subscriber")) { > xlog("***route - challenging"); > www_challenge("openser.org", "0"); > exit; > }; > > if (isflagset(5)) { > xlog("***route - isflagset(5)"); > setflag(6); > # if you want OPTIONS natpings uncomment > next > # setflag(7); > }; > save("location"); > xlog("***route - registered"); > exit; > }; > > if (!lookup("location")) { > sl_send_reply("404", "Not Found"); > xlog("***route - 404, Not found"); > exit; > }; > append_hf("P-hint: usrloc applied\r\n"); > }; > > route(1); > xlog("***end***\n"); > } > > > route[1] { > xlog("***route1***\n"); > if (subst_uri('/(sip:.*);nat=yes/\1/')){ > xlog("***route[1] - setflag(6)"); > setflag(6); > }; > > if (isflagset(5)||isflagset(6)) { > xlog("***route[1] - route(3)"); > route(3); > } > > if (!t_relay()) { > xlog("***route[1] - error"); > sl_reply_error(); > }; > xlog("***end - route[1]"); > exit; > } > > route[2]{ > xlog("***route2***\n"); > force_rport(); > if (nat_uac_test("19")) { > xlog("***route2 - nat_uac_test(19)\n"); > if (method=="REGISTER") { > xlog("***route2 - register\n"); > fix_nated_register(); > } else { > xlog("***route2 - contact\n"); > fix_nated_contact(); > }; > setflag(5); > }; > } > > route[3] { > xlog("***route3***\n"); > if (is_method("BYE|CANCEL")) { > xlog("***route3 - unforce\n"); > unforce_rtp_proxy(); > } else if (is_method("INVITE")){ > xlog("***route3 - force\n"); > force_rtp_proxy("i"); > t_on_failure("1"); > }; > if (isflagset(5)) { > xlog("***route3 - isflagset(5)\n"); > search_append('Contact:.*sip:[^>[:cntrl:]]*', ';nat=yes'); > } > t_on_reply("1"); > } > > failure_route[1] { > xlog("***failureroute1***\n"); > if (isflagset(6) || isflagset(5)) { > xlog("***failroute1 - unforce\n"); > unforce_rtp_proxy(); > } > } > > onreply_route[1] { > xlog("***onreplyroute1***\n"); > if ((isflagset(5) || isflagset(6)) && status=~"(183)|(2[0-9][0-9])") > { > xlog("***onreplyroute1 - force\n"); > force_rtp_proxy("i"); > } > search_append('Contact:.*sip:[^>[:cntrl:]]*', ';nat=yes'); > > if (isflagset(6)) { > xlog("***onreplyroute1 - contact\n"); > fix_nated_contact(); > } > xlog("***end - onreplyrout[1]"); > exit; > } > > > Thanks, > > Eric > > > > _______________________________________________ > Users mailing list > [email protected] > http://lists.openser.org/cgi-bin/mailman/listinfo/users _______________________________________________ Users mailing list [email protected] http://lists.openser.org/cgi-bin/mailman/listinfo/users
