Hi, Is there any way through which I can sent the Media from my VoipSwitch and signalling from my Openser
Regards Tushar -----Original Message----- From: Daniel-Constantin Mierla [mailto:[EMAIL PROTECTED] Sent: Monday, July 07, 2008 3:13 PM To: Tushar Cc: [email protected] Subject: Re: [OpenSER-Users] using voipswitch as media server Hello, On 07/07/08 12:30, Tushar wrote: > Hi Daniel, > > I am looking for this type of solution- > > > UDP + RTP |--------| UDP |------| UDP + RTP > UA-----------| Openser|---------| |------------UA > |--------| |client| > | UDP | | > | |Server| > |--------| RTP | | > | VoipSwi|---------| | > |--------| |------| > > I am confused how to configure OpenSer so it can communicate with voipswitch > > If I install RTPProxy and On the SER machine add the following line to > openser.cfg > > modparam("nathelper", "rtpproxy_sock", "udp:voipswitch IPAddr:12345"). > > Will it help me out? > the communication done via rtpproxy_sock is a proprietary protocol specified and implemented by the developer of nathelper module and rtpproxy application. I do not know what is your voipswitch, but I doubt it knows this protocol unless it uses the rtpproxy inside. Cheers, Daniel > Regards > Tushar > > -----Original Message----- > From: Daniel-Constantin Mierla [mailto:[EMAIL PROTECTED] > Sent: Monday, July 07, 2008 2:42 PM > To: Tushar > Cc: 'Iñaki Baz Castillo'; [email protected] > Subject: Re: [OpenSER-Users] using voipswitch as media server > > Hello, > > On 07/07/08 08:37, Tushar wrote: > >> Thanks Castillo, >> >> How can I direct all media to my voipswitch? >> The signalling will land on Openser server, SDP will decide the route for >> RTP so what step should be taken to sent the RTP to my voipswitch. >> >> > is there a way to instruct the voip switch to open ports for RTP > streams? As steps, once the invite comes in, you should contact the > voipswitch and ask for a new pair of RTP ports for the call. Once you > get the port and the ip address of the voipswitch, you have to change > them in the sdp -- perhaps mangler module helps. When 200ok is received, > you have to change also the ip and port in sdp with the ones from > voipswitch. > > This algorithm is used for nat traversal with rtpproxy or mediaproxy. > You can check the sources of mediaproxy or nathelper modules for more > details. > > Cheers, > Daniel > > >> Regards >> Tushar >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Iñaki Baz Castillo >> Sent: Sunday, July 06, 2008 5:48 PM >> Cc: [email protected] >> Subject: Re: [OpenSER-Users] using voipswitch as media server >> >> 2008/7/5 Tushar <[EMAIL PROTECTED]>: >> >> >>> I have recently started playing around with Openser, I am looking for a >>> solution in which my Openser Server should carry the signalling part and >>> >>> >> my >> >> >>> media stream should be handle by my voipswitch so I can monitor my RTP >>> stream, work with my calling card solution. >>> >>> While browsing I came to know about mediaproxy rely and media server may >>> >>> >> be >> >> >>> it help me to sent my RTP packet from my server but I like to use my voip >>> switch for my media stream. >>> >>> >> Hi, please don't use HTML (italic text) in the maillist but plain text ;) >> >> About your question... I don't know which is your question. You have a >> voip switch so you don't need a RTP proxy (as MediaProxy is). In your >> case (if you have the control of the voip switch) you just need >> MediaProxy in those cases: >> - You have NATted clients and your switch doesn't handle NAT (if it >> doesn't support "Comedia" mode). >> - You want all the audio through some hosts (in which MediaProxy >> servers run) in order to monitorize it propely (but you could also do >> it in your switch if it's allows it). >> >> >> >> > > -- Daniel-Constantin Mierla http://www.asipto.com _______________________________________________ Users mailing list [email protected] http://lists.openser.org/cgi-bin/mailman/listinfo/users
