David, In this case, instead of using the "expensive" solution of a b2bua, why don't you take care of properly re-write the contact. The question is why do you replace the received contact with the IP of your opensips ?
Regards, Bogdan David Santiago wrote: > I'm not explicitly routing that BYE, but as Andrew Pogrebennyk pointed > out, since I'm "rewriting the Contact header with OpenSIPS address it > is expected that BYE won't go any further than OpenSIPs proxy" and > therefore my only solutions seems to be the configuration of the b2bua > modules. Isn't it? > > On Mon, Oct 11, 2010 at 6:35 PM, Bogdan-Andrei Iancu > <bog...@voice-system.ro> wrote: > >> Hi David, >> >> ok, so the BYE is sent to the wrong destination - how do you route BYE in >> your script? do you use the standard "loose_route" block ? >> >> Regards, >> Bogdan >> >> David Santiago wrote: >> >>> As I said it is being forwarded to the jain slee server that >>> originated it. The effect is the same as if it was replied. >>> >>> The flow is: >>> step 1: [JAIN SLEE SERVER] ---BYE--> [OPENSIPS] [VOIP >>> PROVIDER] >>> step 2: [JAIN SLEE SERVER] <---BYE-- [OPENSIPS] [VOIP >>> PROVIDER] >>> >>> that BYE should be forwarded to the VOIP provider, instead. >>> >>> I'm having a look at how to configure the b2bua thing should this >>> problem be fixed. >>> >>> Thanks for the follow up, Bogdan. >>> >>> >>> David >>> >>> On Fri, Oct 8, 2010 at 1:38 PM, Bogdan-Andrei Iancu >>> <bog...@voice-system.ro> wrote: >>> >>> >>>> Hi David, >>>> >>>> my question is what happens with the BYE: >>>> - is it replied by opensips ? >>>> - is it forwarded to some whatever destination ? >>>> >>>> Regards, >>>> Bogdan >>>> >>>> David Santiago wrote: >>>> >>>> >>>>> Bogdan, right now it's being forwarded again to the slee server who sent >>>>> it, as I'm basically using the configuration provided in >>>>> http://www.opensips.org/html/docs/modules/1.6.x/dispatcher.html >>>>> >>>>> On Wed, Oct 6, 2010 at 4:16 PM, Bogdan-Andrei Iancu >>>>> <bog...@voice-system.ro <mailto:bog...@voice-system.ro>> wrote: >>>>> >>>>> Hi David, >>>>> >>>>> Is the BYE replied or forwarded to whatever destination ? >>>>> >>>>> probably your record routing is somehow broken. OpenSIPS may >>>>> misroute the BYE because the invalid route set - posting the 200 >>>>> OK for INVITE and the BYE will help in investigating this. >>>>> >>>>> Regards, >>>>> Bogdan >>>>> >>>>> David Santiago wrote: >>>>> >>>>> Hi all, >>>>> >>>>> I have a running OpenSIPS installation that I'm using for >>>>> testing purposes. >>>>> >>>>> The fact is that I'm forwarding requests from a voip provider >>>>> to a jain slee server and everything is working fine (INVITEs, >>>>> ACKs, RTP flow,...), except for the BYEs generated from the >>>>> server side. They reach the OpenSIPs proxy and are not >>>>> forwarded to the voip provider in order to finish the call. >>>>> >>>>> I'm not sure if I have to manually setup a route for this to >>>>> happen, or if this behaviour is only available by using the >>>>> B2BUA approach in OpenSIPS. >>>>> >>>>> >>>>> Thanks a lot! >>>>> >>>>> David >>>>> >>>>> -- Bogdan-Andrei Iancu OpenSIPS Bootcamp 15 - 19 November 2010, Edison, New Jersey, USA www.voice-system.ro _______________________________________________ Users mailing list Users@lists.opensips.org http://lists.opensips.org/cgi-bin/mailman/listinfo/users