Thank you Giovanni.
*Thanks & Regards* *Sasmita Panda* *Senior Network Testing and Software Engineer* *3CLogic , ph:07827611765* On Tue, Sep 3, 2019 at 1:48 PM Giovanni Maruzzelli <gmar...@gmail.com> wrote: > Sasmita, > > are you sure you try hard enough before writing to M-L? > > I never used this command, I tried three times, and found how. > > Maybe you don't try enough? > > (opensips-cli): mi get_statistics statistics=all > > > -giovanni > > On Tue, Sep 3, 2019 at 10:10 AM Sasmita Panda <spa...@3clogic.com> wrote: > >> If I am running this command it giving me below output . >> >> (opensips-cli): mi mem_pkg_dump log_level=4 pid=13019 >> "OK" >> >> (opensips-cli): mi mem_shm_dump >> "OK" >> >> What should I do with this . I need the output like how much memory >> getting used at that time . >> >> This is the output through opensipsctl in opensips-1.11 which I was using >> earlier . >> [root@sip spanda]# /usr/local/sbin/opensipsctl fifo get_statistics shmem: >> shmem:total_size = 4294967296 >> shmem:used_size = 5113048 >> shmem:real_used_size = 15605976 >> shmem:max_used_size = 735486296 >> shmem:free_size = 4279361320 >> shmem:fragments = 624271 >> >> I need such output . How I will get this ? >> >> *Thanks & Regards* >> *Sasmita Panda* >> *Senior Network Testing and Software Engineer* >> *3CLogic , ph:07827611765* >> >> >> On Tue, Sep 3, 2019 at 1:29 PM Giovanni Maruzzelli <gmar...@gmail.com> >> wrote: >> >>> then for each command, if you press "tab" it will give you what >>> arguments are needed (if any) >>> >>> (opensips-cli): mi mem_pkg_dump >>> ERROR: command 'mem_pkg_dump' returned: -32602: Invalid params >>> >>> (opensips-cli): mi mem_pkg_dump (->TAB) >>> log_level= pid= >>> >>> >>> On Tue, Sep 3, 2019 at 9:54 AM Giovanni Maruzzelli <gmar...@gmail.com> >>> wrote: >>> >>>> Sasmita, >>>> >>>> execute opensips-cli witouth arguments, then, from inside opensips-cli >>>> shell, type "mi"and enter >>>> >>>> You will see available command, >>>> >>>> then for each of them, you can see possible arguments >>>> >>>> (opensips-cli): mi >>>> ERROR: module 'mi' expects the following commands: get_statistics, >>>> list_statistics, reset_statistics, uptime, version, pwd, arg, which, ps, >>>> kill, log_level, xlog_level, shm_check, cache_store, cache_fetch, >>>> cache_remove, event_subscribe, events_list, subscribers_list, >>>> list_tcp_conns, mem_pkg_dump, mem_shm_dump, mem_rpm_dump, reload_routes, >>>> help, list_blacklists, t_uac_dlg, t_uac_cancel, t_hash, t_reply, >>>> clusterer_reload, clusterer_set_status, clusterer_list, >>>> clusterer_list_topology, cluster_send_mi, cluster_broadcast_mi, >>>> clusterer_list_cap, clusterer_list_shtags, clusterer_shtag_set_active, >>>> ds_set_state, ds_list, ds_reload, domain_reload, domain_dump, dlg_list, >>>> dlg_list_ctx, dlg_end_dlg, dlg_db_sync, dlg_restore_db, dlg_cluster_sync, >>>> profile_get_size, profile_list_dlgs, profile_get_values, list_all_profiles, >>>> profile_end_dlgs, dlg_push_var, dlg_send_sequential, rtpengine_enable, >>>> rtpengine_show, rtpengine_reload, teardown, trace, trace_start, trace_stop >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> On Tue, Sep 3, 2019 at 7:17 AM Sasmita Panda <spa...@3clogic.com> >>>> wrote: >>>> >>>>> Hi All , >>>>> >>>>> Some commands giving proper output but some are giving error . I am >>>>> not getting any document where its mention how to run these commands . >>>>> >>>>> opensips-cli -x mi "get_statistics" >>>>> >>>>> *SQLAlchemy version: 1.3.3ERROR: command 'get_statistics' returned: >>>>> -32602: Invalid params* >>>>> >>>>> opensips-cli -x mi "list_statistics" >>>>> >>>>> *SQLAlchemy version: 1.3.3ERROR: command 'list_statistics' returned: >>>>> -32000: Server error* >>>>> >>>>> opensips-cli -x mi "mem_pkg_dump" >>>>> >>>>> *SQLAlchemy version: 1.3.3ERROR: command 'mem_pkg_dump' returned: >>>>> -32602: Invalid params* >>>>> >>>>> >>>>> How I will run these commands ? I need to check the package memory and >>>>> shared memory getting used while stress testing . Please do help me . >>>>> >>>>> >>>>> *Thanks & Regards* >>>>> *Sasmita Panda* >>>>> *Senior Network Testing and Software Engineer* >>>>> *3CLogic , ph:07827611765* >>>>> _______________________________________________ >>>>> Users mailing list >>>>> Users@lists.opensips.org >>>>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>>>> >>>> >>>> >>>> -- >>>> Sincerely, >>>> >>>> Giovanni Maruzzelli >>>> OpenTelecom.IT >>>> cell: +39 347 266 56 18 >>>> >>>> >>> >>> -- >>> Sincerely, >>> >>> Giovanni Maruzzelli >>> OpenTelecom.IT >>> cell: +39 347 266 56 18 >>> >>> _______________________________________________ >>> Users mailing list >>> Users@lists.opensips.org >>> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >>> >> > > -- > Sincerely, > > Giovanni Maruzzelli > OpenTelecom.IT > cell: +39 347 266 56 18 > > _______________________________________________ > Users mailing list > Users@lists.opensips.org > http://lists.opensips.org/cgi-bin/mailman/listinfo/users >
_______________________________________________ Users mailing list Users@lists.opensips.org http://lists.opensips.org/cgi-bin/mailman/listinfo/users