Hummm... I didn't try a fresh download... That's a good idea... I'll do it tomorrow and let You know the results...
About the 'uncommention', yes, after each update I re-check the main and module/acc Makefiles... just to be sure that everything is ok... Edson >-----Original Message----- >From: Norman Brandinger [mailto:[EMAIL PROTECTED] >Sent: sábado, 15 de setembro de 2007 01:51 >To: Edson >Cc: users@openser.org >Subject: Re: [OpenSER-Users] RE: Trunk Compile Error 2 > >Hi, > >1) Are you using: svn co >https://openser.svn.sourceforge.net/svnroot/openser/trunk openser > >1a) Instead of updating, try downloading the entire distribution into an >empty directory. > >2) Did you remember to uncomment the setting below in >modules/acc/Makefile ? Not positive this is required for auth_radius >(because we always uncomment the setting). > ># set ENABLE_RADIUS_ACC to true if you wish to enable RADIUS accounting ># (uncomment next line or 'ENABLE_RADIUS_ACC=true make all') >ENABLE_RADIUS_ACC=true > >Norm > >Edson wrote: >> Hi, Norman... >> >> Thanks for Your response, but I already have radiusclient-ng version >0.5.6 >> installed... >> >> If radiusclient-ng where not installed, the same 'make' command wouldn't >> compile branche 1.2. Maybe TRUNK has some diferent requirement... Isn't >this >> version enough? >> >> Edson >> >> >>> -----Original Message----- >>> From: Norman Brandinger [mailto:[EMAIL PROTECTED] >>> Sent: sábado, 15 de setembro de 2007 00:20 >>> To: Edson >>> Cc: users@openser.org >>> Subject: Re: [OpenSER-Users] RE: Trunk Compile Error 2 >>> >>> Why not give this a try: >>> >>> cvs >>> -d:pserver:[EMAIL PROTECTED] >ng.berlios.de:/cvsroot/radiusclient- >>> ng >>> login >>> cvs -z3 >>> -d:pserver:[EMAIL PROTECTED] >ng.berlios.de:/cvsroot/radiusclient- >>> ng >>> co radiusclient-ng >>> >>> Regards, >>> Norm >>> >>> Edson wrote: >>> >>>> Just an update info: >>>> >>>> # make modules=modules/auth_radius modules;echo $? >>>> make: *** [modules] Error 2 >>>> 2 >>>> # >>>> >>>> And yes, I need Radius support... >>>> >>>> Edson >>>> >>>> >>>> >>>>> -----Original Message----- >>>>> From: Edson [mailto:[EMAIL PROTECTED] >>>>> Sent: sexta-feira, 14 de setembro de 2007 23:01 >>>>> To: 'users@openser.org' >>>>> Subject: Trunk Compile Error 2 >>>>> >>>>> I'm trying to compile the trunk version. >>>>> >>>>> After updating I run >>>>> make distclean >>>>> and >>>>> make exclude_modules="auth_diameter h350 ldap mi_xmlrpc osp >>>>> postgres unixodbc" modules install >>>>> >>>>> but after I always get: >>>>> >>>>> make[1]: Leaving directory >>>>> `/usr/local/src/VoIP/openser/openser/trunk/modules/auth_db' >>>>> >>>>> make: *** [modules] Error 2 >>>>> >>>>> What is this "Error 2" ? In this same machine I can compile, without a >>>>> glance, branche 1.2 with this same 'make' command. >>>>> >>>>> Thanks for any help.... >>>>> >>>>> Edson >>>>> >>>>> >>>> _______________________________________________ >>>> Users mailing list >>>> Users@openser.org >>>> http://openser.org/cgi-bin/mailman/listinfo/users >>>> >>>> >>>> >>>> >> >> >> >> _______________________________________________ Users mailing list Users@openser.org http://openser.org/cgi-bin/mailman/listinfo/users