Sorry for delay in replying on this, I got pulled into some urgent meetings at the end of the day.
Regarding the questions below, Yes under the H/W tab my QLogic cards are listed. Looks like I have two different models of cards, which could be, I think I acquired them off ebay and then got another one later for redundancy. WWNN and WWPNs are listed. Miultipath -ll lists all my LUNs, multipathing is set to RR... not sure if that could be problem as the SAN I am using (old EMC/DGC CX200) is active passive and I would assume it would be MRU... Hope this helps, still no LUNs showing up in my Engine. Thanks again for your help. Bill -----Original Message----- From: Daniel Helgenberger [mailto:daniel.helgenber...@m-box.de] Sent: 11 September 2014 13:06 To: Bill Dossett Subject: Re: [ovirt-users] FC QLogic question On 11.09.2014 13:05, Bill Dossett wrote: > Hi Daniel, > > I did a lsmod | grep qxl and it returned nothing... did you perhaps mean > qla? > > [root@ovirt141 ~]# lsmod | grep qla > qla2xxx 466573 56 > > I think that is the one Indeed, sorry for that. > > lsscsi does list all of the LUNs... so that's working! Great! > > But nothing in ovirt engine when I try to add a storage domain. Please check back in ovirt engine, with Hosts / Hardware info. You should see the adapter there, along with WWN's ect. I am not quite sure, but AFAIK the node uses dm-multipath by default (for iscsi multipathing). So what does: # multipath -ll list? > > Thanks again, I guess I will try and get a bit further with the installs I > have... > > Bill > > > > -----Original Message----- > From: Daniel Helgenberger [mailto:daniel.helgenber...@m-box.de] > Sent: 11 September 2014 11:53 > To: Bill Dossett > Subject: Re: [ovirt-users] FC QLogic question > > On 11.09.2014 12:17, Bill Dossett wrote: >> Thanks for responding Daniel. > Never mind! >> I was wondering and thought the message may be irrelevant. But yes, >> it doesn't appear to be working. When I try to add a FC storage >> domain, no hosts are showing in the drop down box of hosts. I have >> loaded the latests ovirtnode (3.4.something...) on two hosts now and >> neither are working. > Lets first try to isolate your FC issure. So you are using the latest > ovirt-node? EL6? Keep in mind, the kernel is standard Linux and therefore > should support Qlogic adapters out of the box (IMHO they are the best > supported HBAs in Linux). > Please try a: > # lsmod | grep qxl > to see whatever the qxl module is loaded. Keep in mind you can run into > problems with other conrollers in your host, though I only had this with LSI > SAS / FC controllers so far. > > Further check on the FC switch if the N port is logged in and the zoning is > correct. > > Finally, check with > # lsscsi > if you can see the luns. > >> Also having a lot of issues with configuring the network. I >> configure an interface I can ping it, but it shows as unconfigured... >> on one host I have added it to the manager and I see the interfaces >> anyway, but on the second host I configure the eth0, I can ping it, >> it added to the ovirt engine but it shows no NICs. Should I be using an >> earlier version maybe? >> >> thanks again and best regards. >> >> >> *Bill Dossett* >> *Virtualisation Architect* >> *Pitney Bowes - Tech Central*** >> 6 Hercules Way, 600 Leavesden Park >> Watford, WD25 7GS >> Phone(+44) (0)1923 279353 | VOIP: 54739353 >> Mobile(+44) (0)7775 908612 >> bill.doss...@pb.com <mailto:bill.doss...@pb.com> www.pb.com >> <http://www.pb.com/> *In Engineering?**Raise a ticket via Remedy >> Anywhere [HERE >> <http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Inciden >> t >> /newIncident.aspx>]takes >> less than a minute* >> >> *ManageIQ User Guide available* [*HERE >> <https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%2 >> 0 v4.pdf>*] *Check out the ManageIQ Blog for recent enhancements and >> information [HERE] >> <http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx> >> * >> >> On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger >> <daniel.helgenber...@m-box.de <mailto:daniel.helgenber...@m-box.de>> wrote: >> >>> Hello Bill, >>> >>> what are your problems acually? Is fibre channel not working (as expected)? >>> >>> The log snippet you provided is completly normal and the messages >>> can safely be ignored. This is also unrelated to oVirt but rather >>> CentOS (or the distro you are running) I suppose. >>> >>> Cheers! >>> >>> On 11.09.2014 10:51, Bill Dossett wrote: >>>> Hi, >>>> >>>> I seem to have run into a problem setting up ovirt with Fibre Channel >>>> storage. >>>> >>>> I have a 2MBs SAN and qlogic cards in the nodes. I used this same >>>> setup with RHEV about 6 months ago and it just worked, storage was >>>> there no problems. Now booting with ovirtnode distro, I am seeing >>>> >>>> Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-0091:1: >>>> Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. >>>> >>>> Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx >>>> >>>> Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-00fb:1: >>>> QLogic QLE2460 >>>> - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. >>>> >>>> Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-00fc:1: >>>> ISP2432: PCIe (2.5GT/s x4) @ 0000:0c:00.0 hdma+ host#=1 fw=4.00.26 (2). >>>> >>>> Sep 9 08:01:27 localhost kernel: ata_piix 0000:00:1f.1: PCI INT A >>>> -> GSI 16 (level, low) -> IRQ 16 >>>> >>>> I have googled the firmware error and it says some cards need a >>>> firmware flash and some don't. These are pretty standard HBAs so I >>>> would think they would be supported out of the box, but maybe not. >>>> Looking at trying to add the firmware looked kind of complex - if I >>>> need to do this, does anyone know of a nice and easy howto guide on >>>> this. I'm just getting started with ovirt and appreciate any help >>>> >>>> >>>> Thanks >>>> >>>> *Bill Dossett* >>>> >>>> *Virtualisation Architect* >>>> >>>> *Pitney Bowes - Tech Central*** >>>> >>>> 6 Hercules Way, 600 Leavesden Park >>>> >>>> Watford, WD25 7GS >>>> >>>> Phone(+44) (0)1923 279353 | VOIP: 54739353 >>>> >>>> Mobile(+44) (0)7775 908612 >>>> >>>> bill.doss...@pb.com <mailto:bill.doss...@pb.com> >>>> <mailto:bill.doss...@pb.com> >>>> >>>> www.pb.com <http://www.pb.com> <http://www.pb.com/> >>>> >>>> *In Engineering?**Raise a ticket via Remedy Anywhere [HERE >>>> <http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incid >>>> ent/newIncident.aspx>]takes >>>> >>>> less than a minute* >>>> >>>> *ManageIQ User Guide available*[*HERE >>>> <https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB >>>> %20v4.pdf>*] >>>> >>>> *Check out the ManageIQ Blog for recent enhancements and >>>> information [HERE] >>>> <http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.asp >>>> x>* >>>> >>>> >>>> ------------------------------------------------------------------- >>>> ------------- >>>> >>> -- >>> Daniel Helgenberger >>> m box bewegtbild GmbH >>> >>> P: +49/30/2408781-22 >>> F: +49/30/2408781-10 >>> >>> ACKERSTR. 19 >>> D-10115 BERLIN >>> >>> >>> www.m-box.de <http://www.m-box.de> www.monkeymen.tv >>> <http://www.monkeymen.tv> >>> >>> Geschäftsführer: Martin Retschitzegger / Michaela Göllner >>> Handeslregister: Amtsgericht Charlottenburg / HRB 112767 >>> >> >> --------------------------------------------------------------------- >> - >> ---------- >> > -- > Daniel Helgenberger > m box bewegtbild GmbH > > P: +49/30/2408781-22 > F: +49/30/2408781-10 > > ACKERSTR. 19 > D-10115 BERLIN > > > www.m-box.de www.monkeymen.tv > > Geschäftsführer: Martin Retschitzegger / Michaela Göllner > Handeslregister: Amtsgericht Charlottenburg / HRB 112767 > > > ________________________________ > > -- Daniel Helgenberger m box bewegtbild GmbH P: +49/30/2408781-22 F: +49/30/2408781-10 ACKERSTR. 19 D-10115 BERLIN www.m-box.de www.monkeymen.tv Geschäftsführer: Martin Retschitzegger / Michaela Göllner Handeslregister: Amtsgericht Charlottenburg / HRB 112767 ________________________________ _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users