moin,
i have learned to install a self hosted engine directly to the physical
interfaces.
later you can move it with the hosted engine into the different bonds or vlans.
it works fine by me round 20 times.
br
marcel
Am 3. Februar 2021 19:56:47 MEZ schrieb Nardus Geldenhuys <nard...@gmail.com>:
>Hi oVirt land
>
>Hope you are well. Running into this issue, I hope you can help.
>
>Centos7 and it is updated.
>Ovirt 4.3, latest packages.
>
>My network config:
>
>[root@mob-r1-d-ovirt-aa-1-01 ~]# ip a
>1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
>group
>default qlen 1000
> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> inet 127.0.0.1/8 scope host lo
> valid_lft forever preferred_lft forever
> inet6 ::1/128 scope host
> valid_lft forever preferred_lft forever
>2: ens1f0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq
>master
>bond0 state UP group default qlen 1000
> link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff
>3: ens1f1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq
>master
>bond0 state UP group default qlen 1000
> link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff
>4: enp11s0f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq
>state
>DOWN group default qlen 1000
> link/ether 00:90:fa:c2:d2:50 brd ff:ff:ff:ff:ff:ff
>5: enp11s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq
>state
>DOWN group default qlen 1000
> link/ether 00:90:fa:c2:d2:54 brd ff:ff:ff:ff:ff:ff
>21: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
>noqueue
>state UP group default qlen 1000
> link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff
> inet6 fe80::290:faff:fec2:d248/64 scope link
> valid_lft forever preferred_lft forever
>22: bond0.1131@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
>noqueue state UP group default qlen 1000
> link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff
> inet 172.18.206.184/23 brd 172.18.207.255 scope global bond0.1131
> valid_lft forever preferred_lft forever
> inet6 fe80::290:faff:fec2:d248/64 scope link
> valid_lft forever preferred_lft forever
>
>[root@mob-r1-d-ovirt-aa-1-01 network-scripts]# cat ifcfg-bond0
>BONDING_OPTS='mode=1 miimon=100'
>TYPE=Bond
>BONDING_MASTER=yes
>PROXY_METHOD=none
>BROWSER_ONLY=no
>IPV6INIT=no
>NAME=bond0
>UUID=c11ef6ef-794f-4683-a068-d6338e5c19b6
>DEVICE=bond0
>ONBOOT=yes
>[root@mob-r1-d-ovirt-aa-1-01 network-scripts]# cat ifcfg-bond0.1131
>DEVICE=bond0.1131
>VLAN=yes
>ONBOOT=yes
>MTU=1500
>IPADDR=172.18.206.184
>NETMASK=255.255.254.0
>GATEWAY=172.18.206.1
>BOOTPROTO=none
>MTU=1500
>DEFROUTE=yes
>NM_CONTROLLED=no
>IPV6INIT=yes
>DNS1=172.20.150.10
>DNS2=172.20.150.11
>
>I get the following error:
>
>[ INFO ] TASK [ovirt.hosted_engine_setup : Generate output list]
>[ INFO ] ok: [localhost]
>[ INFO ] TASK [ovirt.hosted_engine_setup : Validate selected bridge
>interface if management bridge does not exists]
>[ INFO ] skipping: [localhost]
> Please indicate a nic to set ovirtmgmt bridge on: (bond0,
>bond0.1131) [bond0.1131]:
> Please specify which way the network connectivity should be
>checked (ping, dns, tcp, none) [dns]:
>..
>..
>..
>..
>..
>[ INFO ] ok: [localhost]
>[ INFO ] TASK [ovirt.hosted_engine_setup : Validate selected bridge
>interface if management bridge does not exists]
>[ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "The
>selected network interface is not valid"}
>[ ERROR ] Failed to execute stage 'Closing up': Failed executing
>ansible-playbook
>[ INFO ] Stage: Clean up
>
>And if I create the ifcfg-ovirtmgmt as a bridge it fails later.
>
>What is the correct network setup for my bond configuration to do a
>self
>hosted-engine setup ?
>
>Regards
>
>Nar
_______________________________________________
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/MRBIY4SJIANR5KE65OIQHNFSJHI7XD2S/
