Hi Neel, Indeed I use the default HG image but I tested the setup with port 1 (still no luck). I have installed the following version (copied from the output of uhd_find_devices): UHD_003.010.002.000-3-g122bfae1.
Given that, should I try with the XG image (even though the setup should work with HG and port 1)? On Sun, Nov 12, 2017 at 5:38 PM Neel Pandeya <[email protected]> wrote: > Hello Gilad: > > You are probably using the HG image, which is the default, and with this > image, Port 0 is only 1 Gigabit Ethernet. The XG image allows both Port 0 > and Port 1 to be 10 Gigabit Ethernet. Please see the link below. > > > http://files.ettus.com/manual/page_usrp_x3x0.html#x3x0_load_fpga_imgs_fpga_flavours > > Could you use UHD 3.10.2.0, and use the XG image, and let us know your > results? > > Let me know if you have any problems in flashing the XG image onto the > device. > > --​Neel Pandeya > > > > > On 12 November 2017 at 07:13, Gilad Beeri (ApolloShield) via USRP-users < > [email protected]> wrote: > >> Update: >> >> The cables are Intel XDACBL3M cables, any reason why those cables (which >> are functioning as tested between 2 computers) and X710-DA4 won't work the >> USRP X300, while the same NIC and another cable (non-Intel) does work? >> >> >> On Sun, Nov 12, 2017 at 12:20 PM Gilad Beeri (ApolloShield) < >> [email protected]> wrote: >> >>> Hi, >>> I'm trying to set-up a brand new just-opened USRP X300 with 10 GigE SFP+. >>> >>> The equipment I have: >>> >>> 1. X300 + a single SBX-120 >>> 2. 2 Intel SFP+ 10 GigE cables >>> 3. Intel X710-DA4 NIC >>> 4. A motherboard with a standard Ethernet interface >>> 5. Ubuntu 16.04 with kernel 4.10.0-38 >>> 6. i40e driver installed, version 2.3.6, firmware version 6.01. >>> >>> >>> I followed the instructions of setting up a USRP X300. >>> >>> When connecting the SFP+ transceiver to port 0 an Ethernet cable between >>> the transceiver and my Ethernet NIC, ping was successful, finding the >>> device was successful, and I could successfully burn the necessary firmware >>> (HG). Note: tried both UHD 3.10.2 and 3.11. >>> So the USRP basically works. >>> >>> Then tried connecting the SFP+ cable to port 0 -> no link (configured >>> host IP 192.168.10.1). >>> Tried connecting it to port 1 and configuring host IP 192.168.40.1 -> no >>> link. If I reboot the USRP when the cable is connected, only then the port >>> LEDs turn on (not when connecting the cable while the device is already >>> on), but still, no link is detected. >>> >>> Does my Intel X710-DA4 work at all? First, the OS recognizes all 4 >>> interfaces. Second, I put inside it Ettus's transceiver, and connected a >>> network cable from the X710 to my motherboard, configured a local network >>> and successfully pinged. So the X710 does work. >>> >>> Do my Intel SFP+ 10 GigE cables work? Connected them at both ends to >>> SFP+-based computers and successfully transferred a file between them over >>> my SFP+ cables. So the cables work. >>> >>> What else can I try? >>> >>> Thanks >>> >>> >>> >> _______________________________________________ >> USRP-users mailing list >> [email protected] >> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com >> >> >
_______________________________________________ USRP-users mailing list [email protected] http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
