Your Ubuntu system is set up for UHD 4.2 whereas your windows with MatLab is setup for 4.1. You probably can just downgrade to 4.1 firmware when running MatLab on windows. Unless they have a 4.2 compatible UHD build.
Sent from my iPhone > On May 17, 2022, at 9:29 AM, Shehla Amir via USRP-users > <[email protected]> wrote: > > > Hi, > > I have been working with 2 USRP X310. Both have one daughter board installed. > I am facing multiple errors and I can't find relevant documentation. They > were working fine a week ago but now whenever I try to connect using MATLAB I > get the errors mentioned below. Can you please help me in debugging this > issue? > > When I connect using MATLAB and use probesdru command I get the error 'Error: > RuntimeError: Failure to create rfnoc_graph.' > and the probesdru command generate the following output: > > '[INFO] [UHD] Win32; Microsoft Visual C++ version 14.2; Boost_107500; > UHD_4.1.0.4-vendor > [INFO] [X300] X300 initialization sequence... > [INFO] [X300] Maximum frame size: 1472 bytes. > [INFO] [GPS] No GPSDO found > [INFO] [X300] Radio 1x clock: 200 MHz > [ERROR] [RFNOC::GRAPH] IO Error during GSM initialization. > EnvironmentError: IOError: Timed out getting recv buff for management > transaction > [ERROR] [RFNOC::GRAPH] Caught exception while initializing graph: > EnvironmentError: IOError: Timed out getting recv buff for management > transaction > Error: RuntimeError: Failure to create rfnoc_graph. > ' > Moreover, when I use the findsdru command I get the following error: > > ---------- begin libuhd error output ---------- > IO Error during GSM initialization. EnvironmentError: IOError: Timed out > getting recv buff for management transaction > ---------- end libuhd error output ---------- > ---------- begin libuhd error output ---------- > Caught exception while initializing graph: EnvironmentError: IOError: Timed > out getting recv buff for management transaction > ---------- end libuhd error output ---------- > ---------- begin libuhd error output ---------- > Error during initialization of block 0/DUC#0! > ---------- end libuhd error output ---------- > ---------- begin libuhd error output ---------- > Caught exception while initializing graph: RfnocError: OpTimeout: Control > operation timed out waiting for ACK > ---------- end libuhd error output ---------- > ---------- begin libuhd error output ---------- > Error during initialization of block 0/Radio#0! > ---------- end libuhd error output ---------- > ---------- begin libuhd error output ---------- > Caught exception while initializing graph: RfnocError: OpTimeout: Control > operation timed out waiting for ACK > ---------- end libuhd error output ---------- > ---------- begin libuhd error output ---------- > Caught exception while initializing graph: RfnocError: OpTimeout: Control > operation timed out waiting for ACK > ---------- end libuhd error output ---------- > > %%%%%%%%%%%%%%%%%%%%%%%%% > While connecting through ubuntu uhd and using the command ush_usrp_probe I > get the following message: > > [INFO] [UHD] linux; GNU C++ version 9.4.0; Boost_107100; > UHD_4.2.0.0-0ubuntu1~focal1 > [INFO] [X300] X300 initialization sequence... > [INFO] [X300] Maximum frame size: 1472 bytes. > [INFO] [X300] Radio 1x clock: 200 MHz > [WARNING] [UDP] The recv buffer could not be resized sufficiently. > Target sock buff size: 2453333 bytes. > Actual sock buff size: 163840 bytes. > See the transport application notes on buffer resizing. > Please run: sudo sysctl -w net.core.rmem_max=2453333 > [WARNING] [UDP] The send buffer could not be resized sufficiently. > Target sock buff size: 2453333 bytes. > Actual sock buff size: 163840 bytes. > See the transport application notes on buffer resizing. > Please run: sudo sysctl -w net.core.wmem_max=2453333 > [WARNING] [UDP] The current recv_buff_size of 163840 is less than the minimum > recommended size of 816000 and may result in dropped packets on some NICs > [WARNING] [UDP] The current send_buff_size of 163840 is less than the minimum > recommended size of 307200 and may result in dropped packets on some NICs > _____________________________________________________ > / > | Device: X-Series Device > | _____________________________________________________ > | / > | | Mboard: X310 > | | revision: 11 > | | revision_compat: 7 > | | product: 30818 > | | mac-addr0: 00:80:2f:32:8e:52 > | | mac-addr1: 00:80:2f:32:8e:53 > | | gateway: 192.168.10.1 > | | ip-addr0: 192.168.137.4 > | | subnet0: 255.255.255.0 > | | ip-addr1: 192.168.20.2 > | | subnet1: 255.255.255.0 > | | ip-addr2: 192.168.30.2 > | | subnet2: 255.255.255.0 > | | ip-addr3: 192.168.40.2 > | | subnet3: 255.255.255.0 > | | serial: 321741F > | | FW Version: 6.0 > | | FPGA Version: 38.0 > | | FPGA git hash: b1ca7f3 > | | RFNoC capable: Yes > | | > | | Time sources: internal, external, gpsdo > | | Clock sources: internal, external, gpsdo > | | Sensors: ref_locked > | _____________________________________________________ > | / > | | RFNoC blocks on this device: > | | > | | * 0/DDC#0 > | | * 0/DDC#1 > | | * 0/DUC#0 > | | * 0/DUC#1 > | | * 0/Radio#0 > | | * 0/Radio#1 > | | * 0/Replay#0 > | _____________________________________________________ > | / > | | Static connections on this device: > | | > | | * 0/SEP#0:0==>0/DUC#0:0 > | | * 0/DUC#0:0==>0/Radio#0:0 > | | * 0/Radio#0:0==>0/DDC#0:0 > | | * 0/DDC#0:0==>0/SEP#0:0 > | | * 0/Radio#0:1==>0/DDC#0:1 > | | * 0/DDC#0:1==>0/SEP#1:0 > | | * 0/SEP#2:0==>0/DUC#1:0 > | | * 0/DUC#1:0==>0/Radio#1:0 > | | * 0/Radio#1:0==>0/DDC#1:0 > | | * 0/DDC#1:0==>0/SEP#2:0 > | | * 0/Radio#1:1==>0/DDC#1:1 > | | * 0/DDC#1:1==>0/SEP#3:0 > | | * 0/SEP#4:0==>0/Replay#0:0 > | | * 0/Replay#0:0==>0/SEP#4:0 > | | * 0/SEP#5:0==>0/Replay#0:1 > | | * 0/Replay#0:1==>0/SEP#5:0 > | _____________________________________________________ > | / > | | TX Dboard: 0/Radio#0 > | | ID: UBX-160 v2 (0x007d) > | | Serial: 3208538 > | | _____________________________________________________ > | | / > | | | TX Frontend: 0 > | | | Name: UBX TX > | | | Antennas: TX/RX, CAL > | | | Sensors: lo_locked > | | | Freq range: 10.000 to 6000.000 MHz > | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB > | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz > | | | Connection Type: QI > | | | Uses LO offset: No > | _____________________________________________________ > | / > | | RX Dboard: 0/Radio#0 > | | ID: UBX-160 v2 (0x007e) > | | Serial: 3208538 > | | _____________________________________________________ > | | / > | | | RX Frontend: 0 > | | | Name: UBX RX > | | | Antennas: TX/RX, RX2, CAL > | | | Sensors: lo_locked > | | | Freq range: 10.000 to 6000.000 MHz > | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB > | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz > | | | Connection Type: IQ > | | | Uses LO offset: No > | _____________________________________________________ > | / > | | TX Dboard: 0/Radio#1 > | | _____________________________________________________ > | | / > | | | TX Frontend: 0 > | | | Name: Unknown (0xffff) - 0 > | | | Antennas: > | | | Sensors: > | | | Freq range: 0.000 to 0.000 MHz > | | | Gain Elements: None > | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz > | | | Connection Type: IQ > | | | Uses LO offset: No > | _____________________________________________________ > | / > | | RX Dboard: 0/Radio#1 > | | _____________________________________________________ > | | / > | | | RX Frontend: 0 > | | | Name: Unknown (0xffff) - 0 > | | | Antennas: > | | | Sensors: > | | | Freq range: 0.000 to 0.000 MHz > | | | Gain Elements: None > | | | Bandwidth range: 0.0 to 0.0 step 0.0 Hz > | | | Connection Type: IQ > | | | Uses LO offset: No > > Thanks, > > > _______________________________________________ > USRP-users mailing list -- [email protected] > To unsubscribe send an email to [email protected]
_______________________________________________ USRP-users mailing list -- [email protected] To unsubscribe send an email to [email protected]
