Dear community,
I am trying to use OpenAirInterface with an N310 as gNB. I am writing on
this mail list because I think my problem is caused by the configuration
of the N310.
When I run the N310 I get variable errors. When I run it for the first
time after a long time I get no errors.
But when I run it after a short time I get these warnings and errors
(not always all of them):
[WARNING] [MPM.RPCServer] Someone tried to claim this device again
(From: 192.168.20.1)
[WARNING] [MPM.RPCServer] A timeout event occured!
[WARNING] [RFNOC::GRAPH] One or more blocks timed out during flush!
terminate called after throwing an instance of 'uhd::runtime_error'
what(): RuntimeError: rx xport timed out getting a response from
mgmt_portal
Aborted
And these are just a few examples.
I could think of ignoring them, using the N310 only a few minutes after
the previous use. The problem is that the device does not seem to
transmit anything over the air, even on the first try. I say this
because using the same configuration file that I use with a B210 the gNB
does not work, while with the B210 it works and I can connect the
smathphone.
I attach the log file of OperAirInterface.
Also, I frequently get the classic "L" indicating overflow after about
ten seconds.
I have solved a similar problem before (I report a previous mail):
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
I installed the UHD 4.1 version and followed this tutorial:
https://kb.ettus.com/USRP_N300/N310/N320/N321_Getting_Started_Guide for
updating the Linux File System and updating the FPGA Image.
When I try a simple example file:
./rx_ascii_art_dft --freq 98e6 --rate 5e6 --gain 20 --bw 5e6 --ref-lvl -30
I get the following error:
[WARNING] [0/Radio#0] set_rx_bandwidth take no effect on AD9371. Default
analog bandwidth is 100MHz
I cannot find any useful information online, apart from this discussion:
https://www.mail-archive.com/usrp-users@lists.ettus.com/msg05735.html
which did not help me.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Although in the forum it was told to me that this was just a warning, I
fixed it by upgrading the version of UHD to 4.3.
All this suggests to me that there is something messed up in the initial
setup.
Does anyone have any ideas and can help me?
Thanks in advance,
Giuseppe
giuseppe@giuseppe-srv:~/openairinterface5g/cmake_targets/ran_build/build$ sudo
./nr-softmodem -O
../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb.sa.band78.fr1.106PRB.usrpb210_MOD.conf
--sa --continuous-tx
CMDLINE: "./nr-softmodem" "-O"
"../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb.sa.band78.fr1.106PRB.usrpb210_MOD.conf"
"--sa" "--continuous-tx"
[CONFIG] get parameters from libconfig
../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb.sa.band78.fr1.106PRB.usrpb210_MOD.conf
, debug flags: 0x00000000
[LIBCONFIG] Path for include directive set to:
../../../targets/PROJECTS/GENERIC-NR-5GC/CONF
[CONFIG] function config_libconfig_init returned 0
[CONFIG] config module libconfig loaded
[LIBCONFIG] config: 1/1 parameters successfully set, (1 to default value)
[LIBCONFIG] log_config: 3/3 parameters successfully set, (1 to default value)
[LIBCONFIG] log_config: 55/55 parameters successfully set, (47 to default value)
[LIBCONFIG] log_config: 55/55 parameters successfully set, (55 to default value)
[LIBCONFIG] log_config: 16/16 parameters successfully set, (16 to default value)
[LIBCONFIG] log_config: 16/16 parameters successfully set, (16 to default value)
log init done
[HW] # /dev/cpu_dma_latency set to 2 us
Reading in command-line options
[LIBCONFIG] (root): 36/36 parameters successfully set, (32 to default value)
[LIBCONFIG] (root): 5/5 parameters successfully set, (4 to default value)
[ENB_APP] nfapi running mode: MONOLITHIC
[GNB_APP] Getting GNBSParams
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
[LIBCONFIG] THREAD_STRUCT.[0]: 2/2 parameters successfully set, (0 to default
value)
[LIBCONFIG] THREAD_STRUCT.[0]: 2/2 parameters successfully set, (0 to default
value)
[CONFIG] parallel_conf is set to 0
[CONFIG] worker_conf is set to 1
Configuration: nb_rrc_inst 1, nb_nr_L1_inst 1, nb_ru 1
[LIBCONFIG] TTracer: 4/4 parameters successfully set, (4 to default value)
configuring for RAU/RRU
CPU Freq is 2.394626
[ITTI] Starting itti queue: TASK_UNKNOWN as task 0
[ITTI] Starting itti queue: TASK_TIMER as task 1
[ITTI] Starting itti queue: TASK_L2L1 as task 2
[ITTI] Starting itti queue: TASK_BM as task 3
[ITTI] Starting itti queue: TASK_PHY_ENB as task 4
[ITTI] Starting itti queue: TASK_MAC_ENB as task 5
[ITTI] Starting itti queue: TASK_RLC_ENB as task 6
[ITTI] Starting itti queue: TASK_RRC_ENB_NB_IoT as task 7
[ITTI] Starting itti queue: TASK_PDCP_ENB as task 8
[ITTI] Starting itti queue: TASK_DATA_FORWARDING as task 9
[ITTI] Starting itti queue: TASK_END_MARKER as task 10
[ITTI] Starting itti queue: TASK_RRC_ENB as task 11
[ITTI] Starting itti queue: TASK_RRC_GNB as task 12
[ITTI] Starting itti queue: TASK_RAL_ENB as task 13
[ITTI] Starting itti queue: TASK_S1AP as task 14
[ITTI] Starting itti queue: TASK_NGAP as task 15
[ITTI] Starting itti queue: TASK_X2AP as task 16
[ITTI] Starting itti queue: TASK_M2AP_ENB as task 17
[ITTI] Starting itti queue: TASK_M2AP_MCE as task 18
[ITTI] Starting itti queue: TASK_M3AP as task 19
[ITTI] Starting itti queue: TASK_M3AP_MME as task 20
[ITTI] Starting itti queue: TASK_M3AP_MCE as task 21
[ITTI] Starting itti queue: TASK_SCTP as task 22
[ITTI] Starting itti queue: TASK_ENB_APP as task 23
[ITTI] Starting itti queue: TASK_GNB_APP as task 24
[ITTI] Starting itti queue: TASK_MCE_APP as task 25
[ITTI] Starting itti queue: TASK_MME_APP as task 26
[ITTI] Starting itti queue: TASK_FLEXRAN_AGENT as task 27
[ITTI] Starting itti queue: TASK_PHY_UE as task 28
[ITTI] Starting itti queue: TASK_MAC_UE as task 29
[ITTI] Starting itti queue: TASK_RLC_UE as task 30
[ITTI] Starting itti queue: TASK_PDCP_UE as task 31
[ITTI] Starting itti queue: TASK_RRC_UE as task 32
[ITTI] Starting itti queue: TASK_RRC_NRUE as task 33
[ITTI] Starting itti queue: TASK_NAS_UE as task 34
[ITTI] Starting itti queue: TASK_RAL_UE as task 35
[ITTI] Starting itti queue: TASK_GTPV1_U as task 36
[ITTI] Starting itti queue: TASK_CU_F1 as task 37
[ITTI] Starting itti queue: TASK_DU_F1 as task 38
[ITTI] Starting itti queue: TASK_RRC_UE_SIM as task 39
[ITTI] Starting itti queue: TASK_RRC_GNB_SIM as task 40
[ITTI] Starting itti queue: TASK_RRC_NSA_UE as task 41
[ITTI] Starting itti queue: TASK_RRC_NSA_NRUE as task 42
[ITTI] Starting itti queue: TASK_NAS_NRUE as task 43
[LIBCONFIG] opt: 3/3 parameters successfully set, (3 to default value)
[OPT] OPT disabled
[HW] Version: Branch: develop Abrev. Hash: 5091682551 Date: Mon Jul 4
15:03:35 2022 +0000
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
[LIBCONFIG] gNBs.[0]: 27/27 parameters successfully set, (17 to default value)
[NR_PHY] PRB blacklist
[NR_PHY] RC.gNB = 0x557b540349a0
[LIBCONFIG] L1s.[0]: 15/15 parameters successfully set, (10 to default value)
[NR_PHY] RC.gNB[0] = 0x7fab6c0c5010
[NR_PHY] Copying 0 blacklisted PRB to L1 context
Initializing northbound interface for L1
[PHY] l1_north_init_gNB() RC.nb_nr_L1_inst:1
[PHY] Installing callbacks for IF_Module - UL_indication
[MAC] Allocating shared L1/L2 interface structure for instance 0 @
0x557b540370c0
[PHY] l1_north_init_gNB() RC.gNB[0] installing callbacks
[ITTI] Created Posix thread TASK_SCTP
[LIBCONFIG] eNBs.[0]: 1/1 parameters successfully set, (1 to default value)
[LIBCONFIG] gNBs.[0]: 1/1 parameters successfully set, (1 to default value)
[X2AP] X2AP is disabled.
[LIBCONFIG] gNBs.[0].NETWORK_INTERFACES: 10/10 parameters successfully set, (3
to default value)
[NGAP] Configuration in the file: demo-oai.
[NGAP] Configuration in the file: 192.168.70.129/24.
[NGAP] Starting NGAP layer
[ITTI] Created Posix thread TASK_NGAP
[PHY] gNB_app_task() Task ready initialize structures
[ITTI] Created Posix thread TASK_GNB_APP
[NR_RRC] Creating NR RRC gNB Task
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
[LIBCONFIG] gNBs.[0]: 27/27 parameters successfully set, (17 to default value)
[NR_PHY] PRB blacklist
[LIBCONFIG] L1s.[0]: 15/15 parameters successfully set, (10 to default value)
[NR_PHY] Copying 0 blacklisted PRB to L1 context
Initializing northbound interface for L1
[PHY] l1_north_init_gNB() RC.nb_nr_L1_inst:1
[PHY] Installing callbacks for IF_Module - UL_indication
[PHY] l1_north_init_gNB() RC.gNB[0] installing callbacks
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
[LIBCONFIG] gNBs.[0]: 27/27 parameters successfully set, (17 to default value)
[LIBCONFIG] MACRLCs.[0]: 31/31 parameters successfully set, (25 to default
value)
[MAC] [MAIN] Init function start:nb_nr_macrlc_inst=1
[NR_RRC] Entering main loop of NR_RRC message task
[ITTI] Created Posix thread TASK_RRC_GNB
[PHY] Installing callbacks for IF_Module - UL_indication
[NR_MAC] PUSCH Target 150, PUCCH Target 200, PUCCH Failure 10, PUSCH Failure
10
[PHY] gNB_app_task() RC.nb_nr_L1_inst:1
[PHY] l1_north_init_gNB() RC.nb_nr_L1_inst:1
[PHY] Installing callbacks for IF_Module - UL_indication
[PHY] l1_north_init_gNB() RC.gNB[0] installing callbacks
[GNB_APP] Allocating gNB_RRC_INST for 1 instances
[PHY] gNB_app_task() RC.nb_nr_inst:1 RC.nrrrc:0x7fab60007110
[PHY] gNB_app_task() Creating RRC instance RC.nrrrc[0]:0x7fab60007130 (1 of 1)
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
[LIBCONFIG] gNBs.[0]: 27/27 parameters successfully set, (17 to default value)
[LIBCONFIG] gNBs.[0].pdcch_ConfigSIB1.[0]: 2/2 parameters successfully set, (0
to default value)
[LIBCONFIG] gNBs.[0].servingCellConfigCommon.[0]: 60/60 parameters successfully
set, (9 to default value)
[RRC] Read in ServingCellConfigCommon (PhysCellId 0, ABSFREQSSB 641280,
DLBand 78, ABSFREQPOINTA 640008, DLBW 106,RACH_TargetReceivedPower -96
[NR_MAC] NR band duplex spacing is 0 KHz (nr_bandtable[37].band = 78)
[NR_MAC] NR band 78, duplex mode TDD, duplex spacing = 0 KHz
[NR_MAC] NR band duplex spacing is 0 KHz (nr_bandtable[37].band = 78)
[NR_MAC] NR band 78, duplex mode TDD, duplex spacing = 0 KHz
[LIBCONFIG] list gNBs.[0].servingCellConfigDedicated not found in config file
../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb.sa.band78.fr1.106PRB.usrpb210_MOD.conf
NRRRC 0: Southbound Transport local_mac
[NR_RRC] Setting node_type to ngran_gNB
[LIBCONFIG] gNBs.[0].plmn_list.[0]: 3/3 parameters successfully set, (0 to
default value)
[GNB_APP] pdsch_AntennaPorts N1 1
[GNB_APP] pdsch_AntennaPorts N2 1
[GNB_APP] pdsch_AntennaPorts XP 1
[GNB_APP] pusch_AntennaPorts 1
[GNB_APP] minTXRXTIME 6
[GNB_APP] SIB1 TDA 1
[GNB_APP] Do CSI-RS 1
[GNB_APP] Do SRS 1
[GNB_APP] 256 QAM: may be on
[GNB_APP] SDAP layer is disabled
[LIBCONFIG] security: 4/4 parameters successfully set, (0 to default value)
[GNB_APP] RRC starting with node type 2
[GNB_APP] Sending configuration message to NR_RRC task
[PDCP] pdcp init,usegtp
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
[NR_RRC] Received message NRRRC_CONFIGURATION_REQ
[LIBCONFIG] gNBs.[0]: 27/27 parameters successfully set, (17 to default value)
[NR_RRC] [gNB 0] Received NRRRC_CONFIGURATION_REQ : 0x7fab60008780
[NR_RRC] [FRAME 00000][gNB][MOD 00][RNTI 0] Init...
[LIBCONFIG] gNBs.[0].plmn_list.[0]: 3/3 parameters successfully set, (0 to
default value)
[LIBCONFIG] gNBs.[0].plmn_list.[0].snssaiList.[0]: 2/2 parameters successfully
set, (0 to default value)
[NR_MAC] NR band duplex spacing is 0 KHz (nr_bandtable[37].band = 78)
[LIBCONFIG] gNBs.[0].plmn_list.[0].snssaiList.[1]: 2/2 parameters successfully
set, (0 to default value)
[NR_MAC] NR band 78, duplex mode TDD, duplex spacing = 0 KHz
[NR_RRC] [FRAME 00000][gNB][MOD 00][RNTI 0] Checking release
[LIBCONFIG] gNBs.[0].amf_ip_address.[0]: 4/4 parameters successfully set, (0 to
default value)
[LIBCONFIG] gNBs.[0].SCTP: 2/2 parameters successfully set, (0 to default value)
[NR_RRC] SIB1 freq: absoluteFrequencySSB 641280, absoluteFrequencyPointA
640008
[NR_RRC] SIB1 freq: absolute_diff 1272, 2*(absolute_diff/(12*2) - 10) 86
<SIB1>
<cellSelectionInfo>
<q-RxLevMin>[LIBCONFIG] gNBs.[0].NETWORK_INTERFACES: 10/10 parameters
successfully set, (3 to default value)
-65</q-RxLevMin>
[GNB_APP] default drx 0
</cellSelectionInfo>
<cellAccessRelatedInfo>
[GTPU] Configuring GTPu
<plmn-IdentityList>
[LIBCONFIG] (root): 2/2 parameters successfully set, (0 to default value)
<PLMN-IdentityInfo>
<plmn-IdentityList>
<PLMN-Identity>
<mcc>
<MCC-MNC-Digit>0</MCC-MNC-Digit>
<MCC-MNC-Digit>0</MCC-MNC-Digit>
<MCC-MNC-Digit>1</MCC-MNC-Digit>
</mcc>
<mnc>
<MCC-MNC-Digit>0</MCC-MNC-Digit>
<MCC-MNC-Digit>1</MCC-MNC-Digit>
</mnc>
</PLMN-Identity>
</plmn-IdentityList>
<trackingAreaCode>
000000000000000000000001
</trackingAreaCode>
<cellIdentity>
000000000000000000000000111000000000
</cellIdentity>
<cellReservedForOperatorUse><notReserved/></cellReservedForOperatorUse>
</PLMN-IdentityInfo>
</plmn-IdentityList>
</cellAccessRelatedInfo>
<servingCellConfigCommon>
<downlinkConfigCommon>
<frequencyInfoDL>
<frequencyBandList>
<NR-MultiBandInfo>
<freqBandIndicatorNR>78</freqBandIndicatorNR>
</NR-MultiBandInfo>
</frequencyBandList>
<offsetToPointA>86</offsetToPointA>
<scs-SpecificCarrierList>
<SCS-SpecificCarrier>
<offsetToCarrier>0</offsetToCarrier>
<subcarrierSpacing><kHz30/></subcarrierSpacing>
<carrierBandwidth>106</carrierBandwidth>
</SCS-SpecificCarrier>
</scs-SpecificCarrierList>
</frequencyInfoDL>
<initialDownlinkBWP>
<genericParameters>
<locationAndBandwidth>28875</locationAndBandwidth>
<subcarrierSpacing><kHz30/></subcarrierSpacing>
</genericParameters>
<pdcch-ConfigCommon>
<setup>
<controlResourceSetZero>12</controlResourceSetZero>
<searchSpaceZero>0</searchSpaceZero>
<commonSearchSpaceList>
<SearchSpace>
<searchSpaceId>1</searchSpaceId>
<controlResourceSetId>0</controlResourceSetId>
<monitoringSlotPeriodicityAndOffset>
<sl1></sl1>
</monitoringSlotPeriodicityAndOffset>
<monitoringSymbolsWithinSlot>
10000000000000
</monitoringSymbolsWithinSlot>
<nrofCandidates>
<aggregationLevel1><n0/></aggregationLevel1>
<aggregationLevel2><n0/></aggregationLevel2>
<aggregationLevel4><n2/></aggregationLevel4>
<aggregationLevel8><n0/></aggregationLevel8>
<aggregationLevel16><n0/></aggregationLevel16>
</nrofCandidates>
<searchSpaceType>
<common>
<dci-Format0-0-AndFormat1-0>
</dci-Format0-0-AndFormat1-0>
</common>
</searchSpaceType>
</SearchSpace>
<SearchSpace>
<searchSpaceId>5</searchSpaceId>
<controlResourceSetId>0</controlResourceSetId>
<monitoringSlotPeriodicityAndOffset>
<sl5>0</sl5>
</monitoringSlotPeriodicityAndOffset>
<duration>2</duration>
<monitoringSymbolsWithinSlot>
10000000000000
</monitoringSymbolsWithinSlot>
<nrofCandidates>
<aggregationLevel1><n0/></aggregationLevel1>
[LIBCONFIG] gNBs.[0].NETWORK_INTERFACES: 10/10 parameters
successfully set, (3 to default value)
<aggregationLevel2><n0/></aggregationLevel2>
<aggregationLevel4><n4/></aggregationLevel4>
<aggregationLevel8><n2/></aggregationLevel8>
[GTPU] SA mode
<aggregationLevel16><n1/></aggregationLevel16>
</nrofCandidates>
[GTPU] Configuring GTPu address : 192.168.70.129 -> 8146a8c0
<searchSpaceType>
<common>
<dci-Format0-0-AndFormat1-0>
</dci-Format0-0-AndFormat1-0>
</common>
</searchSpaceType>
</SearchSpace>
<SearchSpace>
<searchSpaceId>7</searchSpaceId>
<controlResourceSetId>0</controlResourceSetId>
<monitoringSlotPeriodicityAndOffset>
<sl1></sl1>
</monitoringSlotPeriodicityAndOffset>
[GNB_APP] [gNB 0] gNB_app_register for instance 0
[NGAP] Registered new gNB[0] and macro gNB id 3584
<monitoringSymbolsWithinSlot>
[NGAP] [gNB 0] check the amf registration state
10000000000000
</monitoringSymbolsWithinSlot>
<nrofCandidates>
<aggregationLevel1><n0/></aggregationLevel1>
<aggregationLevel2><n0/></aggregationLevel2>
<aggregationLevel4><n4/></aggregationLevel4>
<aggregationLevel8><n2/></aggregationLevel8>
<aggregationLevel16><n1/></aggregationLevel16>
</nrofCandidates>
<searchSpaceType>
<common>
<dci-Format0-0-AndFormat1-0>
</dci-Format0-0-AndFormat1-0>
</common>
</searchSpaceType>
</SearchSpace>
</commonSearchSpaceList>
<searchSpaceSIB1>0</searchSpaceSIB1>
<searchSpaceOtherSystemInformation>7</searchSpaceOtherSystemInformation>
<pagingSearchSpace>5</pagingSearchSpace>
<ra-SearchSpace>1</ra-SearchSpace>
</setup>
</pdcch-ConfigCommon>
<pdsch-ConfigCommon>
<setup>
<pdsch-TimeDomainAllocationList>
<PDSCH-TimeDomainResourceAllocation>
<mappingType><typeA/></mappingType>
<startSymbolAndLength>40</startSymbolAndLength>
</PDSCH-TimeDomainResourceAllocation>
<PDSCH-TimeDomainResourceAllocation>
<mappingType><typeA/></mappingType>
<startSymbolAndLength>54</startSymbolAndLength>
</PDSCH-TimeDomainResourceAllocation>
<PDSCH-TimeDomainResourceAllocation>
<mappingType><typeA/></mappingType>
<startSymbolAndLength>57</startSymbolAndLength>
</PDSCH-TimeDomainResourceAllocation>
</pdsch-TimeDomainAllocationList>
</setup>
</pdsch-ConfigCommon>
</initialDownlinkBWP>
<bcch-Config>
<modificationPeriodCoeff><n2/></modificationPeriodCoeff>
</bcch-Config>
<pcch-Config>
<defaultPagingCycle><rf256/></defaultPagingCycle>
<nAndPagingFrameOffset>
<quarterT>1</quarterT>
</nAndPagingFrameOffset>
<ns><one/></ns>
<firstPDCCH-MonitoringOccasionOfPO>
<sCS120KHZoneT-SCS60KHZhalfT-SCS30KHZquarterT-SCS15KHZoneEighthT>
<INTEGER>0</INTEGER>
</sCS120KHZoneT-SCS60KHZhalfT-SCS30KHZquarterT-SCS15KHZoneEighthT>
</firstPDCCH-MonitoringOccasionOfPO>
</pcch-Config>
</downlinkConfigCommon>
<uplinkConfigCommon>
<frequencyInfoUL>
<scs-SpecificCarrierList>
<SCS-SpecificCarrier>
<offsetToCarrier>0</offsetToCarrier>
<subcarrierSpacing><kHz30/></subcarrierSpacing>
<carrierBandwidth>106</carrierBandwidth>
</SCS-SpecificCarrier>
</scs-SpecificCarrierList>
<p-Max>23</p-Max>
</frequencyInfoUL>
<initialUplinkBWP>
<genericParameters>
<locationAndBandwidth>28875</locationAndBandwidth>
<subcarrierSpacing><kHz30/></subcarrierSpacing>
</genericParameters>
<rach-ConfigCommon>
<setup>
<rach-ConfigGeneric>
<prach-ConfigurationIndex>98</prach-ConfigurationIndex>
<msg1-FDM><one/></msg1-FDM>
<msg1-FrequencyStart>0</msg1-FrequencyStart>
<zeroCorrelationZoneConfig>13</zeroCorrelationZoneConfig>
<preambleReceivedTargetPower>-96</preambleReceivedTargetPower>
<preambleTransMax><n10/></preambleTransMax>
<powerRampingStep><dB2/></powerRampingStep>
<ra-ResponseWindow><sl10/></ra-ResponseWindow>
</rach-ConfigGeneric>
<ssb-perRACH-OccasionAndCB-PreamblesPerSSB>
<one><n60/></one>
</ssb-perRACH-OccasionAndCB-PreamblesPerSSB>
<ra-ContentionResolutionTimer><sf64/></ra-ContentionResolutionTimer>
<rsrp-ThresholdSSB>19</rsrp-ThresholdSSB>
<prach-RootSequenceIndex>
<l139>1</l139>
</prach-RootSequenceIndex>
<msg1-SubcarrierSpacing><kHz30/></msg1-SubcarrierSpacing>
<restrictedSetConfig><unrestrictedSet/></restrictedSetConfig>
</setup>
</rach-ConfigCommon>
<pusch-ConfigCommon>
<setup>
<pusch-TimeDomainAllocationList>
<PUSCH-TimeDomainResourceAllocation>
<k2>6</k2>
<mappingType><typeB/></mappingType>
<startSymbolAndLength>41</startSymbolAndLength>
</PUSCH-TimeDomainResourceAllocation>
<PUSCH-TimeDomainResourceAllocation>
<k2>6</k2>
<mappingType><typeB/></mappingType>
<startSymbolAndLength>38</startSymbolAndLength>
</PUSCH-TimeDomainResourceAllocation>
<PUSCH-TimeDomainResourceAllocation>
<k2>7</k2>
<mappingType><typeB/></mappingType>
<startSymbolAndLength>38</startSymbolAndLength>
</PUSCH-TimeDomainResourceAllocation>
</pusch-TimeDomainAllocationList>
<msg3-DeltaPreamble>1</msg3-DeltaPreamble>
<p0-NominalWithGrant>-90</p0-NominalWithGrant>
</setup>
</pusch-ConfigCommon>
<pucch-ConfigCommon>
<setup>
<pucch-ResourceCommon>0</pucch-ResourceCommon>
<pucch-GroupHopping><neither/></pucch-GroupHopping>
<hoppingId>40</hoppingId>
<p0-nominal>-90</p0-nominal>
</setup>
</pucch-ConfigCommon>
</initialUplinkBWP>
<timeAlignmentTimerCommon><infinity/></timeAlignmentTimerCommon>
</uplinkConfigCommon>
<ssb-PositionsInBurst>
<inOneGroup>
10000000
</inOneGroup>
</ssb-PositionsInBurst>
<ssb-PeriodicityServingCell><ms20/></ssb-PeriodicityServingCell>
<tdd-UL-DL-ConfigurationCommon>
<referenceSubcarrierSpacing><kHz30/></referenceSubcarrierSpacing>
<pattern1>
<dl-UL-TransmissionPeriodicity><ms5/></dl-UL-TransmissionPeriodicity>
<nrofDownlinkSlots>7</nrofDownlinkSlots>
<nrofDownlinkSymbols>6</nrofDownlinkSymbols>
<nrofUplinkSlots>2</nrofUplinkSlots>
<nrofUplinkSymbols>4</nrofUplinkSymbols>
</pattern1>
</tdd-UL-DL-ConfigurationCommon>
<ss-PBCH-BlockPower>-25</ss-PBCH-BlockPower>
</servingCellConfigCommon>
<ue-TimersAndConstants>
<t300><ms400/></t300>
<t301><ms400/></t301>
<t310><ms2000/></t310>
<n310><n10/></n310>
<t311><ms3000/></t311>
<n311><n1/></n311>
<t319><ms400/></t319>
</ue-TimersAndConstants>
</SIB1>
[NR_RRC] do_SIB23_NR, size 9
[NR_RRC] Done init_NR_SI
[NR_MAC] Configuring common parameters from NR ServingCellConfig
[NR_MAC] config_common() dl_BandwidthP:40
[NR_MAC] NR band duplex spacing is 0 KHz (nr_bandtable[37].band = 78)
[NR_MAC] Computing frequency (pointA 640008 => 3600120 KHz (freq_min 3300000
KHz, NR band 78 N_OFFs 620000))
[NR_MAC] config_common() dl_BandwidthP:40
[NR_MAC] NR band duplex spacing is 0 KHz (nr_bandtable[37].band = 78)
[NR_MAC] Computing frequency (pointA 640008 => 3600120 KHz (freq_min 3300000
KHz, NR band 78 N_OFFs 620000))
[NR_MAC] NR band duplex spacing is 0 KHz (nr_bandtable[37].band = 78)
[NR_MAC] NR band 78, duplex mode TDD, duplex spacing = 0 KHz
[NR_MAC] Set RX antenna number to 1, Set TX antenna number to 1 (num ssb 1:
80000000,0)
[NR_MAC] Setting TDD configuration period to 6
[NR_MAC] TDD has been properly configurated
DL frequency 3619200000: band 48, UL frequency 3619200000
[PHY] DL frequency 3619200000 Hz, UL frequency 3619200000 Hz: band 48, uldl
offset 0 Hz
[PHY] Configuring MIB for instance 0, : (Nid_cell 0,DL freq 3619200000, UL
freq 3619200000)
[PHY] Initializing frame parms for mu 1, N_RB 106, Ncp 0
[PHY] Init: N_RB_DL 106, first_carrier_offset 1412, nb_prefix_samples
144,nb_prefix_samples0 176
[PHY] Doing symbol rotation calculation for gNB TX/RX, f0 3619200000.000000
Hz, Nsymb 28
[PHY] Symbol rotation 0/28 => (-32767,-1)
[PHY] Symbol rotation 1/28 => tl 0.000036 (32767,-1) (0.000000)
[PHY] Symbol rotation 2/28 => tl 0.000072 (-32767,-1) (0.500000)
[PHY] Symbol rotation 3/28 => tl 0.000108 (32767,0) (0.000000)
[PHY] Symbol rotation 4/28 => tl 0.000143 (-32767,0) (0.500000)
[PHY] Symbol rotation 5/28 => tl 0.000179 (32767,-1) (0.000000)
[PHY] Symbol rotation 6/28 => tl 0.000215 (-32767,-1) (0.500000)
[PHY] Symbol rotation 7/28 => tl 0.000250 (32767,0) (0.000000)
[PHY] Symbol rotation 8/28 => tl 0.000286 (-32767,-1) (0.500000)
[PHY] Symbol rotation 9/28 => tl 0.000322 (32767,0) (1.000000)
[PHY] Symbol rotation 10/28 => tl 0.000357 (-32767,-1) (0.500000)
[PHY] Symbol rotation 11/28 => tl 0.000393 (32767,0) (1.000000)
[PHY] Symbol rotation 12/28 => tl 0.000429 (-32767,-1) (0.500000)
[PHY] Symbol rotation 13/28 => tl 0.000464 (32767,0) (1.000000)
[PHY] Symbol rotation 14/28 => tl 0.000500 (-32767,-1) (0.500000)
[PHY] Symbol rotation 15/28 => tl 0.000536 (32767,0) (1.000000)
[PHY] Symbol rotation 16/28 => tl 0.000572 (-32767,-1) (0.500000)
[PHY] Symbol rotation 17/28 => tl 0.000608 (32767,0) (1.000000)
[PHY] Symbol rotation 18/28 => tl 0.000643 (-32767,-1) (0.500000)
[PHY] Symbol rotation 19/28 => tl 0.000679 (32767,0) (1.000000)
[PHY] Symbol rotation 20/28 => tl 0.000715 (-32767,-1) (0.500000)
[PHY] Symbol rotation 21/28 => tl 0.000750 (32766,0) (1.000000)
[PHY] Symbol rotation 22/28 => tl 0.000786 (-32767,-1) (0.500000)
[PHY] Symbol rotation 23/28 => tl 0.000822 (32766,0) (1.000000)
[PHY] Symbol rotation 24/28 => tl 0.000857 (-32767,-1) (0.500000)
[PHY] Symbol rotation 25/28 => tl 0.000893 (32766,0) (1.000000)
[PHY] Symbol rotation 26/28 => tl 0.000929 (-32767,-1) (0.500000)
[PHY] Symbol rotation 27/28 => tl 0.000964 (32766,0) (1.000000)
[PHY] Doing symbol rotation calculation for gNB TX/RX, f0 3619200000.000000
Hz, Nsymb 28
[PHY] Symbol rotation 0/28 => (-32767,-1)
[PHY] Symbol rotation 1/28 => tl 0.000036 (32767,-1) (0.000000)
[PHY] Symbol rotation 2/28 => tl 0.000072 (-32767,-1) (0.500000)
[PHY] Symbol rotation 3/28 => tl 0.000108 (32767,0) (0.000000)
[PHY] Symbol rotation 4/28 => tl 0.000143 (-32767,0) (0.500000)
[PHY] Symbol rotation 5/28 => tl 0.000179 (32767,-1) (0.000000)
[PHY] Symbol rotation 6/28 => tl 0.000215 (-32767,-1) (0.500000)
[PHY] Symbol rotation 7/28 => tl 0.000250 (32767,0) (0.000000)
[PHY] Symbol rotation 8/28 => tl 0.000286 (-32767,-1) (0.500000)
[PHY] Symbol rotation 9/28 => tl 0.000322 (32767,0) (1.000000)
[PHY] Symbol rotation 10/28 => tl 0.000357 (-32767,-1) (0.500000)
[PHY] Symbol rotation 11/28 => tl 0.000393 (32767,0) (1.000000)
[PHY] Symbol rotation 12/28 => tl 0.000429 (-32767,-1) (0.500000)
[PHY] Symbol rotation 13/28 => tl 0.000464 (32767,0) (1.000000)
[PHY] Symbol rotation 14/28 => tl 0.000500 (-32767,-1) (0.500000)
[PHY] Symbol rotation 15/28 => tl 0.000536 (32767,0) (1.000000)
[PHY] Symbol rotation 16/28 => tl 0.000572 (-32767,-1) (0.500000)
[PHY] Symbol rotation 17/28 => tl 0.000608 (32767,0) (1.000000)
[PHY] Symbol rotation 18/28 => tl 0.000643 (-32767,-1) (0.500000)
[PHY] Symbol rotation 19/28 => tl 0.000679 (32767,0) (1.000000)
[PHY] Symbol rotation 20/28 => tl 0.000715 (-32767,-1) (0.500000)
[PHY] Symbol rotation 21/28 => tl 0.000750 (32766,0) (1.000000)
[PHY] Symbol rotation 22/28 => tl 0.000786 (-32767,-1) (0.500000)
[PHY] Symbol rotation 23/28 => tl 0.000822 (32766,0) (1.000000)
[PHY] Symbol rotation 24/28 => tl 0.000857 (-32767,-1) (0.500000)
[PHY] Symbol rotation 25/28 => tl 0.000893 (32766,0) (1.000000)
[PHY] Symbol rotation 26/28 => tl 0.000929 (-32767,-1) (0.500000)
[PHY] Symbol rotation 27/28 => tl 0.000964 (32766,0) (1.000000)
[PHY] Timeshift symbol rotation 0 => (32767,0) 0.000000
[PHY] Timeshift symbol rotation 1 => (32717,1809) -0.055223
[PHY] Timeshift symbol rotation 2 => (32567,3612) -0.110447
[PHY] Timeshift symbol rotation 3 => (32318,5404) -0.165670
[PHY] Timeshift symbol rotation 4 => (31971,7179) -0.220893
[PHY] Timeshift symbol rotation 5 => (31526,8933) -0.276117
[PHY] Timeshift symbol rotation 6 => (30985,10659) -0.331340
[PHY] Timeshift symbol rotation 7 => (30349,12353) -0.386563
[PHY] Timeshift symbol rotation 8 => (29621,14010) -0.441786
[PHY] Timeshift symbol rotation 9 => (28803,15623) -0.497010
[PHY] gNB 0 configured
[NR_MAC] In rrc_mac_config_req_gNB: slot 0 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 1 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 2 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 3 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 4 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 5 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 6 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 7 DL 1 UL 1
[NR_MAC] In rrc_mac_config_req_gNB: slot 8 DL 0 UL 1
[NR_MAC] In rrc_mac_config_req_gNB: slot 9 DL 0 UL 1
[NR_MAC] In rrc_mac_config_req_gNB: slot 10 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 11 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 12 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 13 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 14 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 15 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 16 DL 1 UL 0
[NR_MAC] In rrc_mac_config_req_gNB: slot 17 DL 1 UL 1
[NR_MAC] In rrc_mac_config_req_gNB: slot 18 DL 0 UL 1
[NR_MAC] In rrc_mac_config_req_gNB: slot 19 DL 0 UL 1
[NR_RRC] [FRAME 00000][gNB][MOD 00][RNTI 0] gNB:OPENAIR NR RRC IN....
[ITTI] Created Posix thread TASK_GTPV1_U
[GTPU] Initializing UDP for local address 192.168.70.129 with port 2152
[GTPU] bind: Cannot assign requested address
[GTPU] failed to bind socket: 192.168.70.129 2152
[GTPU] can't create GTP-U instance
[GTPU] Created gtpu instance id: -1
NFAPI MODE:MONOLITHIC
START MAIN THREADS
RC.nb_nr_L1_inst:1
Initializing gNB threads single_thread_flag:1 wait_for_sync:0
[PHY] Initializing gNB 0 single_thread_flag:1
[PHY] Initializing gNB 0
[PHY] Registering with MAC interface module (before 0x557b540370c0)
[PHY] Installing callbacks for IF_Module - UL_indication
[PHY] Registering with MAC interface module (after 0x557b540370c0)
[PHY] Setting indication lists
[PHY] [nr-gnb.c] gNB structure allocated
wait_gNBs()
Waiting for gNB L1 instances to all get configured ... sleeping 50ms
(nb_nr_sL1_inst 1)
gNB L1 are configured
About to Init RU threads RC.nb_RU:1
Initializing RU threads
configuring RU from file
[LIBCONFIG] RUs.[0]: 33/33 parameters successfully set, (21 to default value)
Set RU mask to 1
Creating RC.ru[0]:0x557b54039930
[PHY] RU clock source set as internal
[PHY] Setting time source to internal
Setting function for RU 0 to gNodeB_3GPP
[RU 0] Setting nr_flag 0, nr_band 78, nr_scs_for_raster 1
[PHY] number of L1 instances 1, number of RU 1, number of CPU cores 56
[PHY] DJP - delete code above this
/home/giuseppe/openairinterface5g/executables/nr-ru.c:1946
[PHY] Copying frame parms from gNB in RC to gNB 0 in ru 0 and frame_parms in
ru
configuring ru_id 0 (start_rf 0x557b501b15e0)
[PHY] Starting ru_thread 0
[PHY] Initializing RU proc 0 (,synch_to_ext_device),
[PHY] Starting RU 0 (,synch_to_ext_device),
[PHY] Initializing frame parms for mu 1, N_RB 106, Ncp 0
[PHY] Init: N_RB_DL 106, first_carrier_offset 1412, nb_prefix_samples
144,nb_prefix_samples0 176
[PHY] fp->scs=30000
[PHY] fp->ofdm_symbol_size=2048
[PHY] fp->nb_prefix_samples0=176
[PHY] fp->nb_prefix_samples=144
[PHY] fp->slots_per_subframe=2
[PHY] fp->samples_per_subframe_wCP=57344
[PHY] fp->samples_per_frame_wCP=573440
[PHY] fp->samples_per_subframe=61440
[PHY] fp->samples_per_frame=614400
[PHY] fp->dl_CarrierFreq=3619200000
[PHY] fp->ul_CarrierFreq=3619200000
[PHY] Channel 0: setting tx_gain offset 6, rx_gain offset 108, tx_freq
3619200000 Hz, rx_freq 3619200000 Hz, tune_offset 0 Hz
[PHY] Initializing RU signal buffers (if_south local RF) nb_tx 1, nb_rx 1
[PHY] [INIT] common.txdata[0] = 0x7fab64303040 (2457600 bytes,sf_extension 0)
[PHY] [INIT] common.txdata[0] = 0x7fab64303040
[PHY] nb_tx 1
[PHY] rxdata_7_5kHz[0] 0x7fab47f0f040 for RU 0
[PHY] [INIT] common.txdata_BF= 0x7fab4c000b00 (8 bytes)
[PHY] txdataF_BF[0] 0x7fab6c08c040 for RU 0
[PHY] rxdataF[0] 0x7fab64039040 for RU 0
[PHY] init feptx thread 0
[PHY] [INIT] nr_phy_init_RU() ru->num_gNB:1
[PHY] init feptx thread 1
wait RUs
[PHY] Waiting for RUs to be configured ... RC.ru_mask:01
[LIBCONFIG] device.recplay: 8/8 parameters successfully set, (8 to default
value)
[LIBCONFIG] device: 1/1 parameters successfully set, (1 to default value)
[LIBCONFIG] loader: 2/2 parameters successfully set, (2 to default value)
[LIBCONFIG] loader.oai_device: 2/2 parameters successfully set, (1 to default
value)
shlib_path liboai_device.so
[LOADER] library liboai_device.so successfully loaded
[HW] openair0_cfg[0].sdr_addrs == 'addr = 192.168.20.2'
[HW] openair0_cfg[0].clock_source == '0' (internal = 0, external = 1)
[HW] UHD version 4.3.0.HEAD-15-g5333d3d1 (4.3.0)
[HW] Checking for USRP with args addr = 192.168.20.2
[INFO] [UHD] linux; GNU C++ version 7.5.0; Boost_106501;
UHD_4.3.0.HEAD-15-g5333d3d1
[HW] Found USRP n3xx
Found USRP n310
net.core.rmem_max = 62500000
net.core.wmem_max = 62500000
[INFO] [MPMD] Initializing 1 device(s) in parallel with args:
mgmt_addr=192.168.20.2,type=n3xx,product=n310,serial=3211008,name=ni-n3xx-3211008,fpga=HG,claimed=False,addr=192.168.20.2,master_clock_rate=122880000.000000
[WARNING] [MPM.RPCServer] A timeout event occured!
[INFO] [MPM.PeriphManager] init() called with device args
`fpga=HG,master_clock_rate=122880000.000000,mgmt_addr=192.168.20.2,name=ni-n3xx-3211008,product=n310,clock_source=internal,time_source=internal'.
[HW] Setting clock source to internal
[HW] Setting time source to internal
-- Using calibration table: calib_table_n310
[HW] device_init() sample_rate:61440000
[HW] cal 0: freq 3500000000.000000, offset 0.000000, diff 119200000.000000
[HW] cal 1: freq 2660000000.000000, offset 0.000000, diff 959200000.000000
[HW] cal 2: freq 2300000000.000000, offset 0.000000, diff 1319200000.000000
[HW] cal 3: freq 1880000000.000000, offset 0.000000, diff 1739200000.000000
[HW] cal 4: freq 816000000.000000, offset 0.000000, diff 2803200000.000000
[HW] RX Gain too high, lower by 33.000000 dB
[HW] RX Gain 0 108.000000 (0.000000) => 108.000000 (max 75.000000)
[HW] USRP TX_GAIN:59.00 gain_range:65.00 tx_gain:6.00
[HW] Actual master clock: 122.880000MHz...
[HW] Actual clock source internal...
[HW] Actual time source internal...
[HW] RF board max packet size 2000, size for 100µs jitter 6144
[HW] rx_max_num_samps 2000
[HW] setting rx channel 0
[INFO] [0/Radio#0] Re-initializing dboard to apply bandwidth settings. This may
take some time.
[INFO] [0/Radio#0] Bandwidth settings applied: 40000000.000000
[INFO] [0/Radio#0] Re-initializing dboard to apply bandwidth settings. This may
take some time.
[INFO] [0/Radio#0] Bandwidth settings applied: 40000000.000000
[HW] RX Channel 0
[HW] Actual RX sample rate: 61.440000MSps...
[HW] Actual RX frequency: 3.619200GHz...
[HW] Actual RX gain: 75.000000...
[HW] Actual RX bandwidth: 40.000000M...
[HW] Actual RX antenna: RX2...
[HW] TX Channel 0
[HW] Actual TX sample rate: 61.440000MSps...
[HW] Actual TX frequency: 3.619200GHz...
[HW] Actual TX gain: 59.000000...
[HW] Actual TX bandwidth: 40.000000M...
[HW] Actual TX antenna: TX/RX...
[HW] Actual TX packet size: 2000
[HW] Device timestamp: 1.697745...
[HW] [RAU] has loaded USRP N300 device.
setup_RU_buffers: frame_parms = 0x557b5403d200
[PHY] RU 0 Setting N_TA_offset to 800 samples (factor 2.000000, UL Freq
3600120, N_RB 106, mu 1)
[PHY] Signaling main thread that RU 0 is ready, sl_ahead 6
waiting for sync (ru_thread,-1/0x557b50e052b4,0x557b51bb6520,0x557b51a0b600)
RC.ru_mask:00
[PHY] RUs configured
ALL RUs READY!
RC.nb_RU:1
ALL RUs ready - init gNBs
Not NFAPI mode - call init_eNB_afterRU()
[PHY] init_eNB_afterRU() RC.nb_nr_inst:1
[PHY] RC.nb_nr_CC[inst:0]:0x7fab6c0c5010
[PHY] [gNB 0] phy_init_nr_gNB() About to wait for gNB to be configured
[LIBCONFIG] loader.dfts: 2/2 parameters successfully set, (1 to default value)
shlib_path libdfts.so
[LOADER] library libdfts.so successfully loaded
[LIBCONFIG] loader.ldpc: 2/2 parameters successfully set, (1 to default value)
shlib_path libldpc.so
[LOADER] library libldpc.so successfully loaded
[PHY] Initialise nr transport
[PHY] Allocating Transport Channel Buffers for PUCCH 0/16
[PHY] Allocating Transport Channel Buffers for PUCCH 1/16
[PHY] Allocating Transport Channel Buffers for PUCCH 2/16
[PHY] Allocating Transport Channel Buffers for PUCCH 3/16
[PHY] Allocating Transport Channel Buffers for PUCCH 4/16
[PHY] Allocating Transport Channel Buffers for PUCCH 5/16
[PHY] Allocating Transport Channel Buffers for PUCCH 6/16
[PHY] Allocating Transport Channel Buffers for PUCCH 7/16
[PHY] Allocating Transport Channel Buffers for PUCCH 8/16
[PHY] Allocating Transport Channel Buffers for PUCCH 9/16
[PHY] Allocating Transport Channel Buffers for PUCCH 10/16
[PHY] Allocating Transport Channel Buffers for PUCCH 11/16
[PHY] Allocating Transport Channel Buffers for PUCCH 12/16
[PHY] Allocating Transport Channel Buffers for PUCCH 13/16
[PHY] Allocating Transport Channel Buffers for PUCCH 14/16
[PHY] Allocating Transport Channel Buffers for PUCCH 15/16
[PHY] Allocating Transport Channel Buffers for SRS 0/16
[PHY] Allocating Transport Channel Buffers for SRS 1/16
[PHY] Allocating Transport Channel Buffers for SRS 2/16
[PHY] Allocating Transport Channel Buffers for SRS 3/16
[PHY] Allocating Transport Channel Buffers for SRS 4/16
[PHY] Allocating Transport Channel Buffers for SRS 5/16
[PHY] Allocating Transport Channel Buffers for SRS 6/16
[PHY] Allocating Transport Channel Buffers for SRS 7/16
[PHY] Allocating Transport Channel Buffers for SRS 8/16
[PHY] Allocating Transport Channel Buffers for SRS 9/16
[PHY] Allocating Transport Channel Buffers for SRS 10/16
[PHY] Allocating Transport Channel Buffers for SRS 11/16
[PHY] Allocating Transport Channel Buffers for SRS 12/16
[PHY] Allocating Transport Channel Buffers for SRS 13/16
[PHY] Allocating Transport Channel Buffers for SRS 14/16
[PHY] Allocating Transport Channel Buffers for SRS 15/16
[PHY] Allocating Transport Channel Buffers for ULSCH 0/8
[PHY] Allocating Transport Channel Buffers for ULSCH 1/8
[PHY] Allocating Transport Channel Buffers for ULSCH 2/8
[PHY] Allocating Transport Channel Buffers for ULSCH 3/8
[PHY] Allocating Transport Channel Buffers for ULSCH 4/8
[PHY] Allocating Transport Channel Buffers for ULSCH 5/8
[PHY] Allocating Transport Channel Buffers for ULSCH 6/8
[PHY] Allocating Transport Channel Buffers for ULSCH 7/8
[PHY] Mapping RX ports from 1 RUs to gNB 0
[PHY] gNB->num_RU:1
[PHY] Attaching RU 0 antenna 0 to gNB antenna 0
[PHY] Number of threads requested in config file: 4, Number of threads
available on this machine: 56
create a thread for core -1
create a thread for core -1
create a thread for core -1
create a thread for core -1
[PHY] Allocating Transport Channel Buffers for DLSCH 0/8
[PHY] Allocating Transport Channel Buffers for DLSCH 1/8
[PHY] Allocating Transport Channel Buffers for DLSCH 2/8
[PHY] Allocating Transport Channel Buffers for DLSCH 3/8
[PHY] Allocating Transport Channel Buffers for DLSCH 4/8
[PHY] Allocating Transport Channel Buffers for DLSCH 5/8
[PHY] Allocating Transport Channel Buffers for DLSCH 6/8
[PHY] Allocating Transport Channel Buffers for DLSCH 7/8
[PHY] Allocating Transport Channel Buffers for DLSCH 0/8
[PHY] Allocating Transport Channel Buffers for DLSCH 1/8
[PHY] Allocating Transport Channel Buffers for DLSCH 2/8
[PHY] Allocating Transport Channel Buffers for DLSCH 3/8
[PHY] Allocating Transport Channel Buffers for DLSCH 4/8
[PHY] Allocating Transport Channel Buffers for DLSCH 5/8
[PHY] Allocating Transport Channel Buffers for DLSCH 6/8
[PHY] Allocating Transport Channel Buffers for DLSCH 7/8
waiting for sync
(L1_stats_thread,-1/0x557b50e052b4,0x557b51bb6520,0x557b51a0b600)
ALL RUs ready - ALL gNBs ready
Sending sync to all threads
About to call end_configmodule() from main()
/home/giuseppe/openairinterface5g/executables/nr-softmodem.c:790
Called end_configmodule() from main()
/home/giuseppe/openairinterface5g/executables/nr-softmodem.c:795
TYPE <CTRL-C> TO TERMINATE
Entering ITTI signals handler
got sync (ru_thread)
got sync (L1_stats_thread)
[PHY] RU 0 rf device ready
[PHY] RU 0 RF started
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
[NR_MAC] Frame.Slot 128.0
[NR_MAC] Frame.Slot 256.0
[NR_MAC] Frame.Slot 384.0
[NR_MAC] Frame.Slot 512.0
_______________________________________________
USRP-users mailing list -- usrp-users@lists.ettus.com
To unsubscribe send an email to usrp-users-le...@lists.ettus.com
