William,
Thank you for response.
RH EL 5.5, VxVM 5.1 SP1
Please see vxprint output below. At the moment my guess is that
/etc/hosts had my hostname as 127.0.0.1 at the time when I ran
"vradmin addsec" command.
[root@nj4lpqamq002 ~]# vxprint -Pl
Disk group: nj4_ric1_vvrdg
Rlink: rlk_ric1lpdrmq002_rvg_nj4_ric1
info: timeout=500 rid=0.1054
latency_high_mark=10000 latency_low_mark=9950
bandwidth_limit=none
state: state=STALE
synchronous=off latencyprot=off srlprot=off
assoc: rvg=rvg_nj4_ric1_vvrdg
remote_host=ric1lpdrmq002 IP_addr=10.67.20.12 port=
remote_dg=nj4_ric1_vvrdg
remote_dg_dgid=
remote_rvg_version=unknown
remote_rlink=rlk_nj4lpqamq002_rvg_nj4_ric1_
remote_rlink_rid=0.0
local_host=nj4lpqamq002 IP_addr=127.0.0.1 port=4145
protocol: TCP/IP
flags: write enabled detached inconsistent cant_sync disconnected
[root@nj4lpqamq002 ~]#
PS I am your student from VxVM class couple of years ago :).
On Thu, Jun 23, 2011 at 11:11 AM, William Havey <[email protected]> wrote:
> What is the OS? release og VVR? Please send the output of vxprint -g <dg>
> -pl. This shows network settings.
>
> Bill
>
> On Wed, Jun 22, 2011 at 7:38 PM, Aleksandr Nepomnyashchiy
> <[email protected]> wrote:
>>
>> Dear List,
>>
>> I am new to VVR ( has configured it once before without any issues,
>> but past performance doesn't guarantee the future results :) )
>>
>> First steps have been completed, but I can't do the initial sync. Any
>> ideas are appreciated.
>>
>>
>> I have done so far:
>> 1. setup a volume group with data volume and srl volume on both
>> primary and secondary nodes
>> 2. updated /etc/vx/vras/.rdg on the secondary node with the ID from
>> the VG from the primary node
>> 3. run "vradmin addsec" and now "vradmin repstatus" shows
>>
>> [root@nj4lpqamq002 ~]# vradmin -g nj4_ric1_vvrdg repstatus
>> rvg_nj4_ric1_vvrdg
>> Replicated Data Set: rvg_nj4_ric1_vvrdg
>> Primary:
>> Host name: nj4lpqamq002
>> RVG name: rvg_nj4_ric1_vvrdg
>> DG name: nj4_ric1_vvrdg
>> RVG state: enabled for I/O
>> Data volumes: 1
>> VSets: 0
>> SRL name: srl_vol
>> SRL size: 1.00 G
>> Total secondaries: 1
>>
>> Secondary:
>> Host name: ric1lpdrmq002
>> RVG name: rvg_nj4_ric1_vvrdg
>> DG name: nj4_ric1_vvrdg
>> Data status: inconsistent
>> Replication status: stopped (primary detached)
>> Current mode: N/A
>> Logging to: SRL
>> Timestamp Information: N/A
>>
>> [root@nj4lpqamq002 ~]#
>>
>>
>>
>> PROBLEM: Attempt to run the full sync gives an error :
>>
>> [root@nj4lpqamq002 ~]#
>> [root@nj4lpqamq002 ~]# vradmin -g nj4_ric1_vvrdg -c ch2347 -full
>> syncrvg rvg_nj4_ric1_vvrdg ric1lpdrmq002
>> Message from Host ric1lpdrmq002:
>> VxVM VVR vxrlink WARNING V-5-1-3532 Rlink
>> rlk_nj4lpqamq002_rvg_nj4_ric1_ is already detached
>> Message from Primary:
>> VxVM VVR vxrsync ERROR V-5-52-2074 Error opening socket between
>> [127.0.0.1] and [10.67.20.12] -- [Invalid argument]
>> VxVM VVR vxrsync ERROR V-5-52-2074 Error opening socket between
>> [127.0.0.1] and [10.67.20.12] -- [connect error]
>> [root@nj4lpqamq002 ~]#
>>
>> I have tried running tcpdump while executing the "full syncrvg" comand
>> above and didn't notice any communication issues.
>>
>>
>> Thank you for your help,
>> Aleksandr
>> _______________________________________________
>> Veritas-vx maillist - [email protected]
>> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-vx
>
>
>
> --
> William (Bill) Havey
> Symantec Certified HA Professional
> 917 515-3385
>
>
_______________________________________________
Veritas-vx maillist - [email protected]
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-vx
