On Wed, Feb 08, 2023 at 02:43:02AM +0000, Parav Pandit wrote: > > > From: Xuan Zhuo <xuanz...@linux.alibaba.com> > > Sent: Tuesday, February 7, 2023 9:25 PM > > > > On Wed, 8 Feb 2023 02:20:27 +0000, Parav Pandit <pa...@nvidia.com> wrote: > > > > > > > From: Xuan Zhuo <xuanz...@linux.alibaba.com> > > > > Sent: Tuesday, February 7, 2023 8:46 PM > > > > > > > > On Tue, 7 Feb 2023 09:06:19 -0500, "Michael S. Tsirkin" > > > > <m...@redhat.com> > > > > wrote: > > > > > On Tue, Feb 07, 2023 at 07:16:34PM +0800, Heng Qi wrote: > > > > > > Currently, the coalescing profile is directly applied to all queues. > > > > > > This patch supports configuring the parameters for a specified > > > > > > queue. > > > > > > > > > > > > When the traffic between queues is unbalanced, for example, one > > > > > > queue is busy and another queue is idle, then it will be very > > > > > > useful to control coalescing parameters at the queue granularity. > > > > > > > > > > ethtool does not support this though, does it? what's the plan? > > > > > > > > > > > > Although it can be done, I think it is difficult to let users use > > > > ethtool to modify the parameters of each queue. > > > > > > > > At present ethtool supports adaptive-rx/adaptive-tx. This is that > > > > the driver automatically adapted to the appropriate parameter. > > > > Generally, it is implemented using netdim in the driver. At this time, > > > > this > > interface is needed. > > > > > > > > > > > > > > > Signed-off-by: Heng Qi <hen...@linux.alibaba.com> > > > > > > Reviewed-by: Xuan Zhuo <xuanz...@linux.alibaba.com> > > > > > > > > > > What I dislike about this interface is that if > > > > > VIRTIO_NET_F_PERQUEUE_NOTF_COAL is negotiated, then in the > > common > > > > case > > > > > of same parameters for all queues driver has to issue multiple > > > > > commands. > > > > > I can see either a special vq index (0xffff ?) or a special > > > > > command used to set it for all queues. > > > > > > > > Although the structure is very similar, in fact, adding a new > > > > command may be clearer. > > > > > > O(N) loop is not that bad when user want to issue change it per device, > > > as this > > is something done very often. > > > Once per VQ is supported, driver may just use the default net-dim to have > > best out of box experience, whenever device supports it. > > > > > > So you mean, we only support the parameters based on Per-Queue. My > > original idea is to support two methods at the same time. > > Yes, if we want to support both the modes, that better to have such command. > Because otherwise the device implementation is bit clumsy which needs to do > the guess work. > For example, driver has configured global params per device. > Now suddenly driver configured first queues parameter. > At this point device should run N-1 queues using global mode and 1 queue with > per Q param.
Seems fine to me. > Similar sequence also occurs when there is per q params configured and > suddenly driver configures global param. In this case I feel global one should win. I think global is just a shortcut for running per queue. > Even in this case now device either must iterate internally and move per q to > global values. > > Better to avoid such complexity in device around implicit and confusing > behavior. > > I see two options. > 1. Just have per VQ params. Software has the full knowledge of in which it is > operating, and state remains at software level. > This effectively achieves both the mode. > > 2. Have a mode cmd, > Mode = (a) per device or (b) per VQ (c) disable > After the mode is set, driver can set per device or per VQ. I like 2 better. I also think a and b are enough. c can be achieved through a. -- MST --------------------------------------------------------------------- To unsubscribe, e-mail: virtio-dev-unsubscr...@lists.oasis-open.org For additional commands, e-mail: virtio-dev-h...@lists.oasis-open.org