Currently PCI device discovery details for the transitional device are documented in two different sections.
For example, PCI device and vendor ID registers are documented in 'Device Requirements: PCI Device Discovery' section, while PCI revision id is documented in 'Legacy Interfaces: A Note on PCI Device Discovery' section. Transitional devices requirements should be documented in "legacy interfaces" section as clearly mentioned in 'Legacy Interface: A Note on Feature Bits'. Hence, 1. Move transitional device requirements to its designated Legacy interface section 2. Describe regular device requirements without quoting it as "non transitional device" While at it, write the description using a singular object definition. Reviewed-by: Satananda Burla <sbu...@marvell.com> Signed-off-by: Parav Pandit <pa...@nvidia.com> --- transport-pci.tex | 70 ++++++++++++++++++++++++----------------------- 1 file changed, 36 insertions(+), 34 deletions(-) diff --git a/transport-pci.tex b/transport-pci.tex index 7f27107..1f74c6f 100644 --- a/transport-pci.tex +++ b/transport-pci.tex @@ -28,46 +28,24 @@ \subsection{PCI Device Discovery}\label{sec:Virtio Transport Options / Virtio Ov \devicenormative{\subsubsection}{PCI Device Discovery}{Virtio Transport Options / Virtio Over PCI Bus / PCI Device Discovery} -Devices MUST have the PCI Vendor ID 0x1af4. -Devices MUST either have the PCI Device ID calculated by adding 0x1040 +The device MUST have the PCI Vendor ID 0x1af4. +The device MUST calculate PCI Device ID by adding 0x1040 to the Virtio Device ID, as indicated in section \ref{sec:Device -Types} or have the Transitional PCI Device ID depending on the device type, -as follows: - -\begin{tabular}{|l|c|} -\hline -Transitional PCI Device ID & Virtio Device \\ -\hline \hline -0x1000 & network device \\ -\hline -0x1001 & block device \\ -\hline -0x1002 & memory ballooning (traditional) \\ -\hline -0x1003 & console \\ -\hline -0x1004 & SCSI host \\ -\hline -0x1005 & entropy source \\ -\hline -0x1009 & 9P transport \\ -\hline -\end{tabular} +Types}. For example, the network device with the Virtio Device ID 1 -has the PCI Device ID 0x1041 or the Transitional PCI Device ID 0x1000. - -The PCI Subsystem Vendor ID and the PCI Subsystem Device ID MAY reflect -the PCI Vendor and Device ID of the environment (for informational purposes by the driver). +has the PCI Device ID 0x1041. -Non-transitional devices SHOULD have a PCI Device ID in the range -0x1040 to 0x107f. -Non-transitional devices SHOULD have a PCI Revision ID of 1 or higher. -Non-transitional devices SHOULD have a PCI Subsystem Device ID of 0x40 or higher. +The device SHOULD have a PCI Device ID in the range 0x1040 to 0x107f. +The device SHOULD have a PCI Revision ID of 1 or higher. +The device SHOULD have a PCI Subsystem Device ID of 0x40 or higher. This is to reduce the chance of a legacy driver attempting to drive the device. +The PCI Subsystem Vendor ID and the PCI Subsystem Device ID MAY reflect +the PCI Vendor and Device ID of the environment (for informational purposes by the driver). + \drivernormative{\subsubsection}{PCI Device Discovery}{Virtio Transport Options / Virtio Over PCI Bus / PCI Device Discovery} Drivers MUST match devices with the PCI Vendor ID 0x1af4 and the PCI Device ID in the range 0x1040 to 0x107f, @@ -85,8 +63,32 @@ \subsection{PCI Device Discovery}\label{sec:Virtio Transport Options / Virtio Ov PCI Subsystem Device ID value. \subsubsection{Legacy Interfaces: A Note on PCI Device Discovery}\label{sec:Virtio Transport Options / Virtio Over PCI Bus / PCI Device Discovery / Legacy Interfaces: A Note on PCI Device Discovery} -Transitional devices MUST have a PCI Revision ID of 0. -Transitional devices MUST have the PCI Subsystem Device ID + +The transitional device has one of the following PCI Device ID +depending on the device type: + +\begin{tabular}{|l|c|} +\hline +Transitional PCI Device ID & Virtio Device \\ +\hline \hline +0x1000 & network device \\ +\hline +0x1001 & block device \\ +\hline +0x1002 & memory ballooning (traditional) \\ +\hline +0x1003 & console \\ +\hline +0x1004 & SCSI host \\ +\hline +0x1005 & entropy source \\ +\hline +0x1009 & 9P transport \\ +\hline +\end{tabular} + +The transitional device MUST have a PCI Revision ID of 0. +The transitional device MUST have the PCI Subsystem Device ID matching the Virtio Device ID, as indicated in section \ref{sec:Device Types}. Transitional devices MUST have the Transitional PCI Device ID in the range 0x1000 to 0x103f. -- 2.26.2 --------------------------------------------------------------------- To unsubscribe, e-mail: virtio-dev-unsubscr...@lists.oasis-open.org For additional commands, e-mail: virtio-dev-h...@lists.oasis-open.org