On Fri, Dec 19, 2014 at 06:38:04PM +0000, Pawel Moll wrote:
> This patch add a support for second version of the virtio-mmio device,
> which follows OASIS "Virtual I/O Device (VIRTIO) Version 1.0"
> specification.
>
> Main changes:
>
> 1. The control register symbolic names use the new device/driver
> nomenclature rather than the old guest/host one.
>
> 2. The driver detect the device version (version 1 is the pre-OASIS
> spec, version 2 is compatible with fist revision of the OASIS spec)
> and drives the device accordingly.
>
> 3. New version uses direct addressing (64 bit address split into two
> low/high register) instead of the guest page size based one,
> and addresses each part of the queue (descriptors, available, used)
> separately.
>
> 4. The device activity is now explicitly triggered by writing to the
> "queue ready" register.
>
> 5. The platform device got a sysfs attribute with the version number.
>
> 6. Whole 64 bit features are properly handled now (both ways).
>
> Signed-off-by: Pawel Moll <pawel.m...@arm.com>
> ---
> I had the code typed for months now, but finally (just before
> disappearing for the end-of-year break) got time to test it (and
> fix the bugs), so I though I'd share it at least as RFC.
>
> It's based on Linus tree still in merge window, but as far as I can
> see all virtio changes have been already pulled, so I don't expect
> any changes in rc1.
>
> Tested with our custom models (*not* qemu).
>
> Regards and till next year!
>
> Pawel
>
> drivers/virtio/virtio_mmio.c | 132
> +++++++++++++++++++++++++++----------------
> include/linux/virtio_mmio.h | 46 +++++++++++----
> 2 files changed, 120 insertions(+), 58 deletions(-)
Thanks! Looks good overall. Some comments below.
> diff --git a/drivers/virtio/virtio_mmio.c b/drivers/virtio/virtio_mmio.c
> index 00d115b..d60675a 100644
> --- a/drivers/virtio/virtio_mmio.c
> +++ b/drivers/virtio/virtio_mmio.c
> @@ -1,7 +1,7 @@
> /*
> * Virtio memory mapped device driver
> *
> - * Copyright 2011, ARM Ltd.
> + * Copyright 2011-2014, ARM Ltd.
> *
> * This module allows virtio devices to be used over a virtual, memory mapped
> * platform device.
> @@ -50,36 +50,6 @@
> *
> *
> *
> - * Registers layout (all 32-bit wide):
> - *
> - * offset d. name description
> - * ------ -- ---------------- -----------------
> - *
> - * 0x000 R MagicValue Magic value "virt"
> - * 0x004 R Version Device version (current max. 1)
> - * 0x008 R DeviceID Virtio device ID
> - * 0x00c R VendorID Virtio vendor ID
> - *
> - * 0x010 R HostFeatures Features supported by the host
> - * 0x014 W HostFeaturesSel Set of host features to access via HostFeatures
> - *
> - * 0x020 W GuestFeatures Features activated by the guest
> - * 0x024 W GuestFeaturesSel Set of activated features to set via
> GuestFeatures
> - * 0x028 W GuestPageSize Size of guest's memory page in bytes
> - *
> - * 0x030 W QueueSel Queue selector
> - * 0x034 R QueueNumMax Maximum size of the currently selected queue
> - * 0x038 W QueueNum Queue size for the currently selected queue
> - * 0x03c W QueueAlign Used Ring alignment for the current queue
> - * 0x040 RW QueuePFN PFN for the currently selected queue
> - *
> - * 0x050 W QueueNotify Queue notifier
> - * 0x060 R InterruptStatus Interrupt status register
> - * 0x064 W InterruptACK Interrupt acknowledge register
> - * 0x070 RW Status Device status register
> - *
> - * 0x100+ RW Device-specific configuration space
> - *
> * Based on Virtio PCI driver by Anthony Liguori, copyright IBM Corp. 2007
> *
> * This work is licensed under the terms of the GNU GPL, version 2 or later.
> @@ -145,11 +115,16 @@ struct virtio_mmio_vq_info {
> static u64 vm_get_features(struct virtio_device *vdev)
> {
> struct virtio_mmio_device *vm_dev = to_virtio_mmio_device(vdev);
> + u64 features;
> +
> + writel(1, vm_dev->base + VIRTIO_MMIO_DEVICE_FEATURES_SEL);
> + features = readl(vm_dev->base + VIRTIO_MMIO_DEVICE_FEATURES);
> + features <<= 32;
>
> - /* TODO: Features > 32 bits */
> - writel(0, vm_dev->base + VIRTIO_MMIO_HOST_FEATURES_SEL);
> + writel(0, vm_dev->base + VIRTIO_MMIO_DEVICE_FEATURES_SEL);
> + features |= readl(vm_dev->base + VIRTIO_MMIO_DEVICE_FEATURES);
>
> - return readl(vm_dev->base + VIRTIO_MMIO_HOST_FEATURES);
> + return features;
> }
>
> static int vm_finalize_features(struct virtio_device *vdev)
> @@ -159,11 +134,13 @@ static int vm_finalize_features(struct virtio_device
> *vdev)
> /* Give virtio_ring a chance to accept features. */
> vring_transport_features(vdev);
>
> - /* Make sure we don't have any features > 32 bits! */
> - BUG_ON((u32)vdev->features != vdev->features);
> + writel(1, vm_dev->base + VIRTIO_MMIO_DRIVER_FEATURES_SEL);
> + writel((vdev->features >> 32) & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_DRIVER_FEATURES);
>
> - writel(0, vm_dev->base + VIRTIO_MMIO_GUEST_FEATURES_SEL);
> - writel(vdev->features, vm_dev->base + VIRTIO_MMIO_GUEST_FEATURES);
> + writel(0, vm_dev->base + VIRTIO_MMIO_DRIVER_FEATURES_SEL);
> + writel(vdev->features & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_DRIVER_FEATURES);
>
> return 0;
> }
> @@ -275,7 +252,12 @@ static void vm_del_vq(struct virtqueue *vq)
>
> /* Select and deactivate the queue */
> writel(index, vm_dev->base + VIRTIO_MMIO_QUEUE_SEL);
> - writel(0, vm_dev->base + VIRTIO_MMIO_QUEUE_PFN);
> + if (vm_dev->version == 1) {
> + writel(0, vm_dev->base + VIRTIO_MMIO_QUEUE_PFN);
> + } else {
> + writel(0, vm_dev->base + VIRTIO_MMIO_QUEUE_READY);
> + WARN_ON(readl(vm_dev->base + VIRTIO_MMIO_QUEUE_READY));
> + }
>
> size = PAGE_ALIGN(vring_size(info->num, VIRTIO_MMIO_VRING_ALIGN));
> free_pages_exact(info->queue, size);
> @@ -312,7 +294,8 @@ static struct virtqueue *vm_setup_vq(struct virtio_device
> *vdev, unsigned index,
> writel(index, vm_dev->base + VIRTIO_MMIO_QUEUE_SEL);
>
> /* Queue shouldn't already be set up. */
> - if (readl(vm_dev->base + VIRTIO_MMIO_QUEUE_PFN)) {
> + if (readl(vm_dev->base + (vm_dev->version == 1 ?
> + VIRTIO_MMIO_QUEUE_PFN : VIRTIO_MMIO_QUEUE_READY))) {
> err = -ENOENT;
> goto error_available;
> }
> @@ -358,10 +341,35 @@ static struct virtqueue *vm_setup_vq(struct
> virtio_device *vdev, unsigned index,
>
> /* Activate the queue */
> writel(info->num, vm_dev->base + VIRTIO_MMIO_QUEUE_NUM);
> - writel(VIRTIO_MMIO_VRING_ALIGN,
> - vm_dev->base + VIRTIO_MMIO_QUEUE_ALIGN);
> - writel(virt_to_phys(info->queue) >> PAGE_SHIFT,
> - vm_dev->base + VIRTIO_MMIO_QUEUE_PFN);
> + if (vm_dev->version == 1) {
> + writel(VIRTIO_MMIO_VRING_ALIGN,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_ALIGN);
> + writel(virt_to_phys(info->queue) >> PAGE_SHIFT,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_PFN);
> + } else {
> + uint64_t addr = virt_to_phys(info->queue);
Kernel normally uses u64 for this type.
> +
> + writel(addr & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_DESC_LOW);
> + writel((addr >> 32) & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_DESC_HIGH);
> +
> + addr += info->num * sizeof(struct vring_desc);
> + writel(addr & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_AVAIL_LOW);
> + writel((addr >> 32) & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_AVAIL_HIGH);
0xffffffff isn't really needed, is it?
> +
> + addr += sizeof(struct vring_avail) + info->num * sizeof(__u16);
> + addr += VIRTIO_MMIO_VRING_ALIGN - 1;
> + addr &= ~(VIRTIO_MMIO_VRING_ALIGN - 1);
Host no longer knows the alignment, so why is it needed?
In fact, I notice that 4.3.2.3 Virtqueue Layout seems completely wrong:
it corresponds to legacy devices, and it does not
say what "align" is.
I think you shouldn't use VIRTIO_MMIO_VRING_ALIGN in non-legacy code:
it's a legacy thing.
> + writel(addr & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_USED_LOW);
> + writel((addr >> 32) & 0xffffffff,
> + vm_dev->base + VIRTIO_MMIO_QUEUE_USED_HIGH);
> +
> + writel(1, vm_dev->base + VIRTIO_MMIO_QUEUE_READY);
> + }
>
> /* Create the vring */
> vq = vring_new_virtqueue(index, info->num, VIRTIO_MMIO_VRING_ALIGN,
> vdev,
> @@ -381,7 +389,12 @@ static struct virtqueue *vm_setup_vq(struct
> virtio_device *vdev, unsigned index,
> return vq;
>
> error_new_virtqueue:
> - writel(0, vm_dev->base + VIRTIO_MMIO_QUEUE_PFN);
> + if (vm_dev->version == 1) {
> + writel(0, vm_dev->base + VIRTIO_MMIO_QUEUE_PFN);
> + } else {
> + writel(0, vm_dev->base + VIRTIO_MMIO_QUEUE_READY);
> + WARN_ON(readl(vm_dev->base + VIRTIO_MMIO_QUEUE_READY));
> + }
> free_pages_exact(info->queue, size);
> error_alloc_pages:
> kfree(info);
> @@ -439,6 +452,18 @@ static const struct virtio_config_ops
> virtio_mmio_config_ops = {
>
> /* Platform device */
>
> +static ssize_t vm_dev_attr_version_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct virtio_mmio_device *vm_dev = platform_get_drvdata(pdev);
> +
> + return snprintf(buf, PAGE_SIZE, "%lu", vm_dev->version);
> +}
> +
> +static struct device_attribute vm_dev_attr_version =
> + __ATTR(version, S_IRUGO, vm_dev_attr_version_show, NULL);
> +
> static int virtio_mmio_probe(struct platform_device *pdev)
> {
> struct virtio_mmio_device *vm_dev;
We already expose feature bits - this one really necessary?
> @@ -476,16 +501,26 @@ static int virtio_mmio_probe(struct platform_device
> *pdev)
>
> /* Check device version */
> vm_dev->version = readl(vm_dev->base + VIRTIO_MMIO_VERSION);
> - if (vm_dev->version != 1) {
> + if (vm_dev->version < 1 || vm_dev->version > 2) {
> dev_err(&pdev->dev, "Version %ld not supported!\n",
> vm_dev->version);
> return -ENXIO;
> }
>
> vm_dev->vdev.id.device = readl(vm_dev->base + VIRTIO_MMIO_DEVICE_ID);
> + if (vm_dev->vdev.id.device == 0) {
> + /*
> + * ID 0 means a dummy (placeholder) device, skip quietly
> + * (as in: no error) with no further actions
> + */
> + return 0;
Necessary?
We don't have drivers for this id anyway.
> + }
Need to also
1. validate that feature bit VIRTIO_1 is set
2. validate that ID is not for a legacy device
otherwise device specific drivers might get invoked
on future devices (e.g. when we update balloon for 1.0)
and they not do the right thing.
> vm_dev->vdev.id.vendor = readl(vm_dev->base + VIRTIO_MMIO_VENDOR_ID);
>
> - writel(PAGE_SIZE, vm_dev->base + VIRTIO_MMIO_GUEST_PAGE_SIZE);
> + if (vm_dev->version == 1)
> + writel(PAGE_SIZE, vm_dev->base + VIRTIO_MMIO_GUEST_PAGE_SIZE);
> +
> + device_create_file(&pdev->dev, &vm_dev_attr_version);
>
> platform_set_drvdata(pdev, vm_dev);
>
> @@ -496,7 +531,8 @@ static int virtio_mmio_remove(struct platform_device
> *pdev)
> {
> struct virtio_mmio_device *vm_dev = platform_get_drvdata(pdev);
>
> - unregister_virtio_device(&vm_dev->vdev);
> + if (vm_dev)
> + unregister_virtio_device(&vm_dev->vdev);
>
Will remove ever be called if probe fails?
> return 0;
> }
> diff --git a/include/linux/virtio_mmio.h b/include/linux/virtio_mmio.h
> index 5c7b6f0..d5f3634 100644
> --- a/include/linux/virtio_mmio.h
> +++ b/include/linux/virtio_mmio.h
> @@ -51,21 +51,22 @@
> /* Virtio vendor ID - Read Only */
> #define VIRTIO_MMIO_VENDOR_ID 0x00c
>
> -/* Bitmask of the features supported by the host
> +/* Bitmask of the features supported by the device (host)
> * (32 bits per set) - Read Only */
> -#define VIRTIO_MMIO_HOST_FEATURES 0x010
> +#define VIRTIO_MMIO_DEVICE_FEATURES 0x010
>
> -/* Host features set selector - Write Only */
> -#define VIRTIO_MMIO_HOST_FEATURES_SEL 0x014
> +/* Device (host) features set selector - Write Only */
> +#define VIRTIO_MMIO_DEVICE_FEATURES_SEL 0x014
>
> -/* Bitmask of features activated by the guest
> +/* Bitmask of features activated by the driver (guest)
> * (32 bits per set) - Write Only */
> -#define VIRTIO_MMIO_GUEST_FEATURES 0x020
> +#define VIRTIO_MMIO_DRIVER_FEATURES 0x020
>
> /* Activated features set selector - Write Only */
> -#define VIRTIO_MMIO_GUEST_FEATURES_SEL 0x024
> +#define VIRTIO_MMIO_DRIVER_FEATURES_SEL 0x024
>
> -/* Guest's memory page size in bytes - Write Only */
> +/* Guest's memory page size in bytes - Write Only
> + * LEGACY DEVICES ONLY! */
This is not the preferred style for multi-line comments :)
Also - maybe add a flag to selectively disable legacy
or modern macros?
Might be clearer than comments that, after all, never compile.
> #define VIRTIO_MMIO_GUEST_PAGE_SIZE 0x028
>
> /* Queue selector - Write Only */
> @@ -77,12 +78,18 @@
> /* Queue size for the currently selected queue - Write Only */
> #define VIRTIO_MMIO_QUEUE_NUM 0x038
>
> -/* Used Ring alignment for the currently selected queue - Write Only */
> +/* Used Ring alignment for the currently selected queue - Write Only
> + * LEGACY DEVICES ONLY! */
> #define VIRTIO_MMIO_QUEUE_ALIGN 0x03c
>
> -/* Guest's PFN for the currently selected queue - Read Write */
> +/* Guest's PFN for the currently selected queue - Read Write
> + * LEGACY DEVICES ONLY! */
> #define VIRTIO_MMIO_QUEUE_PFN 0x040
>
> +/* Ready bit for the currently selected queue - Read Write
> + * NOT FOR LEGACY DEVICES! */
> +#define VIRTIO_MMIO_QUEUE_READY 0x044
> +
> /* Queue notifier - Write Only */
> #define VIRTIO_MMIO_QUEUE_NOTIFY 0x050
>
> @@ -95,6 +102,25 @@
> /* Device status register - Read Write */
> #define VIRTIO_MMIO_STATUS 0x070
>
> +/* Selected queue's Descriptor Table address, 64 bits in two halves
> + * NOT FOR LEGACY DEVICES! */
> +#define VIRTIO_MMIO_QUEUE_DESC_LOW 0x080
> +#define VIRTIO_MMIO_QUEUE_DESC_HIGH 0x084
> +
> +/* Selected queue's Available Ring address, 64 bits in two halves
> + * NOT FOR LEGACY DEVICES! */
> +#define VIRTIO_MMIO_QUEUE_AVAIL_LOW 0x090
> +#define VIRTIO_MMIO_QUEUE_AVAIL_HIGH 0x094
> +
> +/* Selected queue's Used Ring address, 64 bits in two halves
> + * NOT FOR LEGACY DEVICES! */
> +#define VIRTIO_MMIO_QUEUE_USED_LOW 0x0a0
> +#define VIRTIO_MMIO_QUEUE_USED_HIGH 0x0a4
> +
> +/* Configuration atomicity value
> + * NOT FOR LEGACY DEVICES! */
> +#define VIRTIO_MMIO_CONFIG_GENERATION 0x0fc
> +
> /* The config space is defined by each driver as
> * the per-driver configuration space - Read Write */
> #define VIRTIO_MMIO_CONFIG 0x100
> --
> 2.1.0
>
> _______________________________________________
> Virtualization mailing list
> Virtualization@lists.linux-foundation.org
> https://lists.linuxfoundation.org/mailman/listinfo/virtualization
_______________________________________________
Virtualization mailing list
Virtualization@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/virtualization
