Jack--

Thanks for that info.

Bob
  ----- Original Message ----- 
  From: Jack Cole 
  To: [email protected] 
  Sent: Sunday, January 18, 2015 3:59 AM
  Subject: Re: [Vo]:A strange and screwy claim by Piantelli


  Hi Bob,


  The power steps from 10,30,50,70, 90 watts (equal intervals of 1 hour).  The 
temperature is not constant.  The resistance is actually increasing during the 
control run, but you can't see it in that chart because of the scale.  The 
resistance was determined by V/I.  The resistance of the control and active run 
were determined in the same manner.  The voltage and current were measured by 
the power supply, and the connection to the PC was via USB.  The resistance 
coil was not physically disconnected from the supply while it was being loaded 
with material before the active run.  I tried to disturb the setup as little as 
possible during that process.


  The tube furnace is simply a convenient place to house the core providing an 
insulated environment to increase the signal to noise ratio.  It can be used 
for heating, which I have done in previous experiments.  It just takes a lot of 
power to reach the same temperatures.


  I'll do some more charts when I get a chance with time included so you can 
compare to power and temperature.




  On Sat, Jan 17, 2015 at 11:38 PM, Bob Cook <[email protected]> wrote:

    Jack--

    In the following link to the resistance wire plot 
(http://www.lenr-coldfusion.com/wp-content/uploads/2015/01/exp5resistance.png) 
it appears that the resistance of the controls heater wire  did not change.  
Was the temperature of the control constant?  It would be desirable to display 
the time as well as the resistance to understand the input power as well as the 
temperatures.  And how was the resistance determined?  Was it calculated from a 
measurement of voltage and current?  I assume this was the case.  Were both 
resistances of the control and the loaded experiment determined in the same 
manner?  Are you sure the PC connections with the incoming signals recording 
the resistance were sound?  You might want to swap instrument leads around to 
confirm the connections are all ok.  

    You also refer to a decrease in temperature at about 25,000 sec. into the 
run to have been caused by opening the "tube furnace"  What is the purpose of 
the  "tube furnace" in your experiment?  Was this furnace also heated to 
provide an external heat source to the reaction tube, which I understand was 
heated internally with the resistance heating wire?

    If I missed an earlier description of your experiment, please excuse my 
questions and comments.  

    Bob
      ----- Original Message ----- 
      From: Axil Axil 
      To: vortex-l 
      Sent: Saturday, January 17, 2015 8:31 PM
      Subject: Re: [Vo]:A strange and screwy claim by Piantelli


      http://www.lenr-coldfusion.com/2015/01/13/hot-cat-replication-attempt/






      see power drops near 3393 and 3499, but output temperature stays constant.


      On Sat, Jan 17, 2015 at 9:40 PM, <[email protected]> wrote:

        In reply to  Axil Axil's message of Sat, 17 Jan 2015 21:17:13 -0500:
        Hi,
        [snip]
        >If you have noted, at the far end of Jack Cole's temperature curve, the
        >power feed to the heater is still fluctuating but the temperature of 
the
        >reactor stays constant. Has LENR gain set in? I think so.

        Which temperature curve are you referring to?


        >
        >On Sat, Jan 17, 2015 at 9:08 PM, <[email protected]> wrote:
        >
        >> In reply to  Jack Cole's message of Sat, 17 Jan 2015 16:47:13 -0600:
        >> Hi,
        >> [snip]
        >> >Axil,
        >> >
        >> >You may find a plot of a the resistance during the successful run 
vs. the
        >> >control run to be of interest.
        >> >
        >> >
        >> 
http://www.lenr-coldfusion.com/wp-content/uploads/2015/01/exp5resistance.png
        >> >
        >> >Best,
        >> >Jack
        >>
        >> Fast particles interacting with the resistance coil will produce 
many more
        >> ion/electron pairs in the metal, and cause the resistance to drop.
        >>
        >> Regards,
        >>
        >> Robin van Spaandonk
        >>
        >> http://rvanspaa.freehostia.com/project.html
        >>
        >>
        Regards,

        Robin van Spaandonk

        http://rvanspaa.freehostia.com/project.html





Reply via email to