Here we compare what is delivered when the series combinations of air core secondaries are all connected from a method delivering 60 degrees which vectorially sums to appear as an equilateral triangle producing near zero voltage in that combination; to that opposite circuit connection whereby the vector summation is made with two 120 degree angle separations in time. Here that theorized opposite result is actually in deviance to what is expected by the internal compressive voltage measurement made as the standard reference frame. I have made extensive mental inpections of the possibilities involved with taking three coils in series and applying the "double negative" solution. The double negative is simply a wiring compensation made by spatial reversal. In this situation we have three spiral sets of coils in series, each recording a magnetic flux change from its directly adjacent three phase primary source of vibration. When all of these connection methods on identically wound spirals across the three phase source are made from an identical wiring method they can be shown to be in relative symmetry whereby an average 4.4 volts/phase sums to a cancellation showing a third of a volt. By turning the middle seriesed coil in space over now the triple voltage summation reads 9.7 volts. This is about 10% more then what is predicted by the vector analysis assuming that the "opposite of the standard reference frame" will in fact appear as that result, which in this case it does not. It does not because it does not appear as the supplemental phase angle in time that adds to 180 degrees to the initial measurement being used as the standard reference frame. In this case the measurement employing 60 degree angles to determine the distance in time between them does so for the primary signals themselves mirroring a copied action on the secondaries. But when the measurement is made differently using the same 120 degree primary phase input it records the addition of the secondary to secondary mutual induction. The two methods of measurement give different results...These measurements are made from the top three poles of the 666 machine where each starting phase voltage measurement is made from a 50 ft spiral spool of Radio shack Megacable speaker wire. ~ 5 volt stator phase voltage input /delta phase. Three phase air core secondaries each record 4.3, 4.3 and 4.5 volts.https://www.flickr.com/photos/harvich/16570768661/The phase angles are calculated by a triple voltage meter triangulation employing both single and double series measurements of voltage across the three element chain. The three voltage magnitudes are geometrically shown as drawn measurements using a drawing program derived from information of angles between vectors derived by applying the law of cos. The drawing program "confirms" the law of cos angle predictions as any three magnitudes can be formed into a triangle with the Atrix drawing program, and the resultant properties will show the inside phase angles, again corroborating what has already been derived using the law of cos. So here we see a drawing of this symmetry test of voltage compression athttps://www.flickr.com/photos/harvich/15952171743/Triple seriesed voltage expansion from 3 phase symmetryhttps://www.flickr.com/photos/harvich/16571697322/In order to PROOVE a time distortion process, first you have to demonstrate that your sources of 3 phase voltages divided in time three ways are in fact symmetrical with one another, and this requirement is secured when we show those sources placed in series to show the closest to zero voltage cancellation the system approaches. Then we can PREDICT what the voltages will be if no time distortion occurs when we reverse all the wiring connections in the chain. The prediction will be the supplemental angle adding to 180 degrees to the one found on the compression test. Here we find that the actual test of wire reversal produces a result showing phase angles expanded in time reference points in triplicate. A total of 30 degrees has been added to a 240 degree time referenced one. The simple vastly overlooked aspect in the building and discovery involved with three phase air core transformers is the fact that an EXTRA magnetic reaction occurs between those three phase secondaries themselves; where by an accidental or beneficial consequence of the arrangement becomes the fact now two and not one magnetic influences ensue one each secondary, first the main primary coupling one, now added by a secondary to secondary one, each making the cyclic voltage appearance of unobvious energy to appear further apart in time then their primary designations designed them to be. In the laws of primary designations, only two of three series segments could contribute the totality of their voltages on the triple series voltage output as referenced from the middle phase in the chain. Now more then twice is obtained as the primary designation would only yield ~ 8.8 volts. A vector drawing showing deviance between predicted and real voltage output follows athttps://www.flickr.com/photos/harvich/16386478249/HDN Pioneering the Applications of Interphasal Resonances http://tech.groups.yahoo.com/group/teslafy/
