Can I see the packet trace?
/neale
-----Original Message-----
From: 井上里美 <[email protected]>
Date: Wednesday, 18 July 2018 at 09:54
To: "Neale Ranns (nranns)" <[email protected]>, "[email protected]"
<[email protected]>
Cc: "Norimasa Asai (noasai)" <[email protected]>, エッジ仮想化hcoML
<[email protected]>, 小柳達也様
<[email protected]>, N転P_西岡孟朗様
<[email protected]>
Subject: [vpp] VXLAN arp response packet is dropped
Hi neale san,
Thank you for your reply.
We used a vpp packet trace.
show trace is no error but on the caputure device,ARP request
packet is
droped.
It happend the same event even L2.
Could you give me some advice?
【Architecture】
＿＿
｜ ｜→caputure device→IXIA(port 2)
｜VPP｜
｜ ｜←←←←←←←←←IXIA(port 1)
｜＿＿｜
On 2018/07/06 21:39, Neale Ranns (nranns) wrote:
> Hi Satomi
>
> Debugging packet loss is much easier with a VPP packet trace…
>
> Regards,
> neale
>
> -----Original Message-----
> From: <[email protected]> on behalf of 井上里美
<[email protected]>
> Date: Friday, 6 July 2018 at 12:38
> To: "[email protected]" <[email protected]>
> Cc: "Norimasa Asai (noasai)" <[email protected]>, エッジ仮想化hcoML
<[email protected]>, 小柳達也様
<[email protected]>, N転P_西岡孟朗様
<[email protected]>
> Subject: [vpp-dev] [pw] [vpp] VXLAN arp response packet is
dropped
>
> The password is here.
> 1j^?iKvC]C;%
>
> On 2018/07/06 19:37, 井上里美 wrote:
> > Hi VPP Team,
> >
> > I'm Satomi Inoue and I belong to NTT laboratories.
> > Could you tell me why ARP response packet is dropped?
> >
> > We set up vxlan while looking at
> > ”Using_VPP_as_a_VXLAN_Tunnel_Terminator”manual.
> > The procedure is as follows.
> >
> > [The result]
> > ・ARP request packet : IXIA(port2)→VPP→IXIA(port1):OK
> > ・ARP response packet : IXIA(port1)→VPP→IXIA(port2):NG
> > →We checked it by trace command. Loopback interface in
VPP drop the
> > ARP response packet.
> >
> > [set up vxlan]
> > 1. Create sub-interface
> > vpp# create sub-interfaces
VirtualFunctionEthernet0/9/0 1
> > vpp# set interface state
VirtualFunctionEthernet0/9/0.1 up
> >
> > 2. Create bridge-domain
> > create bridge-domain 10001 learn 1 forward 1
uu-flood 1 arp-term 0
> >
> > 3. Create Loopback interface
> > vpp# loopback create mac 1a:2b:3c:4d:5e:6f
> > vpp# set interface state loop0 up
> > vpp# set interface ip address loop0 1.1.1.1/32
> > vpp# set interface ip table loop0 7
> >
> > 4. Apply loopback interface to bride-domain
> > vpp# set interface l2 bridge loop0 10001 bvi
> >
> > 5.Apply sub-interface to bride-domain
> > vpp# set interface l2 bridge
VirtualFunctionEthernet0/9/0.1 10001 0
> >
> > 6.Create VXLAN tunnel
> > vpp# create vxlan tunnel src 1.1.1.1 dst 20.10.0.1
vni 10001
> > encap-vrf-id 7 decap-next l2
> > vpp# set interface l2 bridge vxlan_tunnel0 10001 1
> >
> > Regards,
> > Satomi
>
> --
>
>
>
>
>
--
-----------------------------------------------------
井上里美(Satomi Inoue)
〒180-8585 東京都武蔵野市緑町3-9-11
PHONE:0422-59-4151
E-MAIL:[email protected]
