Hi folks, i want to migrate from meteohub system (via serial interface) to weewx with meteostick.
with meteostick and meteohub i had the problem with poor reception quality of meteostick. i have a davis repeater here, and brought it into operation. with the repeater i got good reception of ISS, soil station and additional temp/hum. only the wireless anemometer station is near enough to be received directly. meanwhile i´ve set up a weewx system with raspian and got the meteostick driver running. but there are a few issues: wind sensor is received by meteostick directly and displayed on the weewx startpage. all other stations (ISS, SoilTemp, additional TempHum) are not displayed on the weewx start page. interestingly the values of the tempsensor on the stick is displayed, but not the values of the pressure sensor. when i got meteostick working, pressure values were displayed, but quitted after few hours. so the only values i get are winddir and speed (via direct reception) and inside temperature. data via the davis repeater are not displayed. maybe i´ve overseen oder forgotten some .conf customizing? file ist attached. i appreciate every help. thx, Michael -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
# WEEWX CONFIGURATION FILE # # Copyright (c) 2009-2015 Tom Keffer <tkef...@gmail.com> # See the file LICENSE.txt for your rights. ############################################################################## # This section is for general configuration information. # Set to 1 for extra debug info, otherwise comment it out or set to zero debug = 0 # Root directory of the weewx data file hierarchy for this station WEEWX_ROOT = / # How long to wait before timing out a socket (FTP, HTTP) connection socket_timeout = 20 # Do not modify this. It is used when installing and updating weewx. version = 3.7.1 ############################################################################## # This section is for information about the station. [Station] # Description of the station location location = Leobendorf # Latitude and longitude in decimal degrees latitude = 48.3 longitude = 16.3 # Altitude of the station, with unit it is in. This is downloaded from # from the station if the hardware supports it. altitude = 180, meter # Set to type of station hardware. There must be a corresponding stanza # in this file with a 'driver' parameter indicating the driver to be used. station_type = Meteostick # If you have a website, you may specify an URL #station_url = http://www.example.com # The start of the rain year (1=January; 10=October, etc.). This is # downloaded from the station if the hardware supports it. rain_year_start = 1 # Start of week (0=Monday, 6=Sunday) week_start = 6 ############################################################################## [Simulator] # This section is for the weewx weather station simulator # The time (in seconds) between LOOP packets. loop_interval = 2.5 # The simulator mode can be either 'simulator' or 'generator'. # Real-time simulator. Sleep between each LOOP packet. mode = simulator # Generator. Emit LOOP packets as fast as possible (useful for testing). #mode = generator # The start time. If not specified, the default is to use the present time. #start = 2011-01-01 00:00 # The driver to use: driver = weewx.drivers.simulator ############################################################################## # This section is for uploading data to Internet sites [StdRESTful] [[StationRegistry]] # To register this weather station with weewx, set this to true register_this_station = false [[AWEKAS]] # This section is for configuring posts to AWEKAS. # If you wish to do this, set the option 'enable' to true, # and specify a username and password. enable = false username = replace_me # To guard against parsing errors, put your password in quotes: password = replace_me [[CWOP]] # This section is for configuring posts to CWOP. # If you wish to do this, set the option 'enable' to true, # and specify the station ID (e.g., CW1234). enable = false station = replace_me # If this is an APRS (radio amateur) station, uncomment # the following and replace with a passcode (e.g., 12345). #passcode = replace_me (APRS stations only) [[PWSweather]] # This section is for configuring posts to PWSweather.com. # If you wish to do this, set the option 'enable' to true, # and specify a station and password. enable = false station = replace_me # To guard against parsing errors, put your password in quotes: password = replace_me [[WOW]] # This section is for configuring posts to WOW. # If you wish to do this, set the option 'enable' to true, # and specify a station and password. enable = false station = replace_me # To guard against parsing errors, put your password in quotes: password = replace_me [[Wunderground]] # This section is for configuring posts to the Weather Underground. # If you wish to do this, set the option 'enable' to true, # and specify a station (e.g., 'KORHOODR3') and password. enable = false station = replace_me # To guard against parsing errors, put your password in quotes: password = replace_me # Set the following to True to have weewx use the WU "Rapidfire" # protocol. Not all hardware can support it. See the User's Guide. rapidfire = False ############################################################################## # This section specifies what reports, using which skins, to generate. [StdReport] # Where the skins reside, relative to WEEWX_ROOT SKIN_ROOT = /etc/weewx/skins # Where the generated reports should go, relative to WEEWX_ROOT HTML_ROOT = /var/www/html/weewx # The database binding indicates which data should be used in reports. data_binding = wx_binding # Each of the following subsections defines a report that will be run. [[StandardReport]] # See the customizing guide to change the units, plot types and line # colors, modify the fonts, display additional sensor data, and other # customizations. Many of those changes can be made here by overriding # parameters, or by modifying templates within the skin itself. # The StandardReport uses the 'Standard' skin, which contains the # images, templates and plots for the report. skin = Standard [[[Units]]] [[[[Groups]]]] group_altitude = meter group_speed2 = meter_per_second2 group_pressure = mbar group_rain = mm group_rainrate = mm_per_hour group_temperature = degree_C group_degree_day = degree_C_day group_speed = meter_per_second [[FTP]] # FTP'ing the results to a webserver is treated as just another report, # albeit one with an unusual report generator! skin = Ftp # If you wish to use FTP, uncomment and fill out the next four lines. #user = replace with the ftp username #password = replace with the ftp password; put in quotes to guard against parsing errors. #server = replace with the ftp server name, e.g, www.threefools.org #path = replace with the ftp destination directory (e.g., /weather) # Set to True for an FTP over TLS (FTPS) connection. Not all servers # support this. secure_ftp = False # To upload files from something other than what HTML_ROOT is set # to above, specify a different HTML_ROOT here. #HTML_ROOT = /var/www/html/weewx # Most FTP servers use port 21 port = 21 # Set to 1 to use passive mode, zero for active mode passive = 1 [[RSYNC]] # rsync'ing to a webserver is treated as just another report skin = Rsync # If you wish to use rsync, you must configure passwordless ssh using # public/private key authentication from the user account that weewx # runs as to the user account on the remote machine where the files # will be copied. # # The following three lines determine where files will be sent. #server = replace with the rsync server name, e.g, www.threefools.org #path = replace with the rsync destination directory (e.g., /weather) #user = replace with the rsync username # Rsync can be configured to remove files from the remote server if # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you # make a mistake in the remote path, you could could unintentionally # cause unrelated files to be deleted. Set to 1 to enable remote file # deletion, zero to allow files to accumulate remotely. delete = 0 ############################################################################## # This service acts as a filter, converting the unit system coming from # the hardware to a unit system in the database. [StdConvert] # The target_unit affects only the unit system in the database. Once # chosen it cannot be changed without converting the entire database. # Modification of target_unit after starting weewx will result in # corrupt data - the database will contain a mix of US and METRIC data. # # The value of target_unit does not affect the unit system for # reporting - reports can display US, Metric, or any combination of units. # # In most cases, target_unit should be left as the default: US # # In particular, those migrating from a standard wview installation # should use US since that is what the wview database contains. # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING! target_unit = US # Options are 'US', 'METRICWX', or 'METRIC' ############################################################################## # This section can adjust data using calibration expressions. [StdCalibrate] [[Corrections]] # For each type, an arbitrary calibration expression can be given. # It should be in the units defined in the StdConvert section. # Example: foo = foo + 0.2 ############################################################################## # This section is for quality control checks. If units are not specified, # values must be in the units defined in the StdConvert section. [StdQC] [[MinMax]] barometer = 26, 32.5, inHg outTemp = -40, 120, degree_F inTemp = 10, 120, degree_F outHumidity = 0, 100 inHumidity = 0, 100 windSpeed = 0, 120, mile_per_hour pressure = 24, 34.5, inHg ############################################################################## # This section controls the origin of derived values. [StdWXCalculate] [[Calculations]] # Derived quantities are calculated by this service. Possible values are: # hardware - use the value provided by hardware # software - use the value calculated by weewx # prefer_hardware - use value provide by hardware if available, # otherwise use value calculated by weewx pressure = prefer_hardware barometer = prefer_hardware altimeter = prefer_hardware windchill = prefer_hardware heatindex = prefer_hardware dewpoint = prefer_hardware inDewpoint = prefer_hardware rainRate = prefer_hardware ############################################################################## # For hardware that supports it, this section controls how often the # onboard clock gets updated. [StdTimeSynch] # How often to check the weather station clock for drift (in seconds) clock_check = 14400 # How much it can drift before we will correct it (in seconds) max_drift = 5 ############################################################################## # This section is for configuring the archive service. [StdArchive] # If the station hardware supports data logging then the archive interval # will be downloaded from the station. Otherwise, specify it (in seconds). archive_interval = 300 # If possible, new archive records are downloaded from the station # hardware. If the hardware does not support this, then new archive # records will be generated in software. # Set the following to "software" to force software record generation. record_generation = hardware # Whether to include LOOP data in hi/low statistics loop_hilo = True # The data binding used to save archive records data_binding = wx_binding ############################################################################## # This section binds a data store to a database. [DataBindings] [[wx_binding]] # The database must match one of the sections in [Databases]. # This is likely to be the only option you would want to change. database = archive_sqlite # The name of the table within the database table_name = archive # The manager handles aggregation of data for historical summaries manager = weewx.wxmanager.WXDaySummaryManager # The schema defines the structure of the database. # It is *only* used when the database is created. schema = schemas.wview.schema ############################################################################## # This section defines various databases. [Databases] # A SQLite database is simply a single file [[archive_sqlite]] database_type = SQLite database_name = weewx.sdb # MySQL [[archive_mysql]] database_type = MySQL database_name = weewx ############################################################################## # This section defines defaults for the different types of databases. [DatabaseTypes] # Defaults for SQLite databases [[SQLite]] driver = weedb.sqlite # Directory in which the database files are located SQLITE_ROOT = /var/lib/weewx # Defaults for MySQL databases [[MySQL]] driver = weedb.mysql # The host where the database is located host = localhost # The user name for logging in to the host user = weewx # The password for the user name. Put in quotes to guard against parsing errors. password = ############################################################################## # This section configures the internal weewx engine. [Engine] [[Services]] # This section specifies the services that should be run. They are # grouped by type, and the order of services within each group # determines the order in which the services will be run. prep_services = weewx.engine.StdTimeSynch data_services = , process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate archive_services = weewx.engine.StdArchive restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS report_services = weewx.engine.StdPrint, weewx.engine.StdReport ############################################################################## [Meteostick] # This section is for the Meteostick USB receiver. # The serial port to which the meteostick is attached, e.g., /dev/ttyS0 port = /dev/ttyUSB0 # Radio frequency to use between USB transceiver and console: US, EU or AU # US uses 915 MHz # EU uses 868.3 MHz # AU uses 915 MHz but has different frequency hopping values than US transceiver_frequency = EU # A channel has value 0-8 where 0 indicates not present # The channel of the Vantage Vue, Pro, or Pro2 ISS iss_channel = 1 # Additional channels apply only to Vantage Pro or Pro2 anemometer_channel = 2 leaf_soil_channel = 7 temp_hum_1_channel = 5 temp_hum_2_channel = 0 # Rain bucket type: 0 is 0.01 inch per tip, 1 is 0.2 mm per tip rain_bucket_type = 1 # The driver to use driver = user.meteostick