I may need to fix that, but I think I had to do all three like this to get it to report the data to AWEKAS properly.
Kevin On Sat, Nov 3, 2018 at 12:03 AM Andrew Milner <andrew.s.r.mil...@gmail.com> wrote: > I'm not sure you should have pressure and barometer and altimeter all > coming from barometer. The accurite should only be providing one pof the > three values - and let weews derive the other two if necessary by > specifying 'software'. The three values should be different values in the > archive. > > On Saturday, 3 November 2018 08:56:05 UTC+2, Kevin Key wrote: >> >> I got it to work! >> >> For anyone else searching for an answer and reading this, here's what I >> did: >> >> Install the Interceptor plugin (as mentioned earlier). >> >> Connected the Acurite Access via a bridged connection on the Raspberry Pi. >> >> Specified the "Observer" hardware. >> >> In weewx.conf: >> >> Scroll down to the "" section and make sure it looks like this: >> >> [Interceptor] >> # This section is for the network traffic interceptor driver. >> >> # The driver to use: >> driver = user.interceptor >> device_type = observer >> mode = sniff >> iface = eth0 >> port = 80 >> pcap_filter = src net 192.168.6.0/24 && dst port 80 >> # NOTE: You'll need to change the above pcap_filter IP address range >> to match that of the one you assigned to the ethernet port on your own >> Raspberry Pi. >> >> # Specify the hardware device to capture. Options include: >> # acurite-bridge - acurite internet bridge >> # observer - fine offset WH2600/HP1000/HP1003, aka 'observer' >> # lw30x - oregon scientific LW301/LW302 >> # lacrosse-bridge - lacrosse GW1000U/C84612 internet bridge >> [[sensor_map]] >> pressure = barometer >> barometer = barometer >> altimeter = barometer >> outHumidity = humidity_out >> outTemp = temperature_out >> windSpeed = wind_speed >> windGust = wind_gust >> windDir = wind_dir >> dewpoint = dewpoint >> rain = rain_total >> >> >> On Thu, Nov 1, 2018 at 10:42 AM vince <vince...@gmail.com> wrote: >> >>> On Thursday, November 1, 2018 at 9:00:22 AM UTC-7, Andrew Milner wrote: >>>> >>>> This post referred to the bridge rather than the sensors - and >>>> Matthew's post implies it is only encrypted from bridge to servers so SDR >>>> should still work with the sensors I believe (don't think they are new) - >>>> however there is no way of knowing if new sensors will be plain or >>>> encrypted in the future!! >>>> >>>> On Thursday, 1 November 2018 16:51:37 UTC+2, Andy wrote: >>>>> >>>>> Can we still use the SDR driver? Is Acurite encrypting the traffic >>>>> from the sensors to the console on new hardware? >>>>> >>>> >>> A little googling led me to a bunch of threads seeming to say that some >>> folks had gotten a SDR type solution working at least notionally. Try a >>> google search for "acurite access with weewx" and look at the threads there >>> especially the ones on wxforum.net >>> >>> Shorter answer is 'some work will probably be required, as it's always >>> more work to go first (or close to first)' >>> >>> There's a lot of chatter on wxforum.net and other sites about Acurite >>> doing things like actually turning off their customer support forums (I >>> didn't check to verify this), but FWIW that company sure doesn't have the >>> best of reputations these days..... >>> >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "weewx-user" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to weewx-user+...@googlegroups.com. >>> For more options, visit https://groups.google.com/d/optout. >>> >> -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to weewx-user+unsubscr...@googlegroups.com. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
