After installing the rtl software and the weewx software on my Pi 4 and getting everything configured I am getting things to work as expected. Just no rain data. I was expecting to have this problem because the output from running the command sudo PYTHONPATH=/usr/share/weewx python /usr/share/weewx/user/sdr.py --cmd="rtl_433 -M utc -F json" is missing the rain data in the parsed section. Notice in the output below that there is a value in the 'rain_in' for the out section, but that rain data is not in the parsed section.
out:[u'{"time" : "2020-05-21 02:27:42", "model" : "Acurite-5n1", "subtype" : 49, "id" : 1066, "channel" : "B", "sequence_num" : 0, "battery_ok" : 1, "wind_avg_km_h" : 14.245, "wind_dir_deg" : 112.500, "rain_in" : 28.500, "mic" : "CHECKSUM"}\n', u'{"time" : "2020-05-21 02:27:42", "model" : "Acurite-5n1", "subtype" : 49, "id" : 1066, "channel" : "B", "sequence_num" : 1, "battery_ok" : 1, "wind_avg_km_h" : 14.245, "wind_dir_deg" : 112.500, "rain_in" : 28.500, "mic" : "CHECKSUM"}\n', u'{"time" : "2020-05-21 02:27:42", "model" : "Acurite-5n1", "subtype" : 49, "id" : 1066, "channel" : "B", "sequence_num" : 2, "battery_ok" : 1, "wind_avg_km_h" : 14.245, "wind_dir_deg" : 112.500, "rain_in" : 28.500, "mic" : "CHECKSUM"}\n'] parsed: {'wind_speed.042A.Acurite5n1PacketV2': 14.245, 'model.042A.Acurite5n1PacketV2': u'Acurite-5n1', 'channel.042A.Acurite5n1PacketV2': u'B', 'wind_dir.042A.Acurite5n1PacketV2': 112.5, 'battery.042A.Acurite5n1PacketV2': 1, 'dateTime': 1590028062, 'freq.042A.Acurite5n1PacketV2': None, 'mod.042A.Acurite5n1PacketV2': None, 'snr.042A.Acurite5n1PacketV2': None, 'sequence_num.042A.Acurite5n1PacketV2': 0, 'noise.042A.Acurite5n1PacketV2': None, 'protocol.042A.Acurite5n1PacketV2': None, 'rssi.042A.Acurite5n1PacketV2': None, 'msg_type.042A.Acurite5n1PacketV2': 49, 'usUnits': 1} I have done a lot of searching on this forum and the web and I understand that there have been many changes to the labeling of rain data on the Acurite 5n1 system. Howerver I just can't figure out where in the code I can make a change that will accept label that my version of the weather station uses for rain. I have done a fair share of programming and I have the help of my son who is a computer science graduate. I feel quite comfortable messing around in the code So far the only change in code that I have tried was to change the line in sdr.py I am running rtl_433 version 20.02-55-gc1d1f9f branch master at 202005162227 thanks for your help -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/cf75a52f-1ada-41c8-a6a8-48e111069cf4%40googlegroups.com.