Well, I think I found something in restx.py.
For CWOP, there is a line that says
_baro = record.get('altimeter')
Well, looking at my loop data there is no altimeter field in it.
I do see in the startup that it says
weewx.wxservices: The following values will be calculated:
altimeter=prefer_hardware, appTemp=prefer_hardware,
barometer=prefer_hardware, beaufort=prefer_hardware,
cloudbase=prefer_hardware, dewpoint=prefer_hardware, ET=prefer_hardware,
heatindex=prefer_hardware, humidex=prefer_hardware,
inDewpoint=prefer_hardware, maxSolarRad=prefer_hardware,
pressure=prefer_hardware, rainRate=prefer_hardware,
windchill=prefer_hardware, windrun=prefer_hardware
Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.wxservices: The
following algorithms will be used for calculations: altimeter=aaASOS,
maxSolarRad=RS
So, apparently, altimeter is something that is supposed to be calculated,
but for whatever reason, when code tries to grab it for CWOP, it's set to
'None'.
I've temporarily changed to code to point at barometer, but I'm guessing
that's the wrong solution and what I need to figure out is why the data for
altimeter is 'None'
On Monday, January 4, 2021 at 2:21:10 PM UTC-8 Brent Dowell wrote:
> A couple months ago I moved my weather station to run on a Raspberry pi,
> and things have been running smoothly with the exception of the data that
> gets uploaded to CWOP.
>
> I upload data to cwop, wunderground, pwsweather, and my own weather site.
> The only one missing the data is cwop.
>
> I'm running weewx version 4.0.0b9 on python Python 2.7.16 with a vantage
> vue weather station.
>
> I've attached below the cwop data, loop data, and syslog.
>
> Thanks in advance for any help.
>
>
>
> My raw data for cwop has a b..... for the barometric data.
>
> ------------------------------------------------------------------------------------------------------
> {Manually
> obfuscated}>APRS,TCPXX*,qAX,CWOP-4:@032150z3949.85N/11938.56W_315/009g014t050r000p000P000b.....h46.weewx-4.0.0b9-Vantage
>
>
> Loop Data looks like:
>
> ------------------------------------------------------------------------------------------------------
> LOOP: 2021-01-04 13:48:42 PST (1609796922) appTemp: 27.7561312321,
> barometer: 29.922, beaufort: 7, cloudbase: 6804.06549784,
> consBatteryVoltage: 4.75, dateTime: 1609796922, dayET: 0.0, dayRain: 0.01,
> dewpoint: 39.7661118095, extraAlarm1: 0, extraAlarm2: 0, extraAlarm3: 0,
> extraAlarm4: 0, extraAlarm5: 0, extraAlarm6: 0, extraAlarm7: 0,
> extraAlarm8: 0, forecastIcon: 3, forecastRule: 187, heatindex: 50.3,
> humidex: 50.3, inDewpoint: 36.425696503, inHumidity: 32.0, insideAlarm: 0,
> inTemp: 67.3, leafWet4: 0.0, maxSolarRad: 340.146433311, monthET: 0.0,
> monthRain: 0.01, outHumidity: 67.0, outsideAlarm1: 0, outsideAlarm2: 0,
> outTemp: 50.3, pressure: 25.4481125632, rain: None, rainAlarm: 0, rainRate:
> 0.0, soilLeafAlarm1: 0, soilLeafAlarm2: 0, soilLeafAlarm3: 0,
> soilLeafAlarm4: 0, stormRain: 0.0, sunrise: 1609774320.0, sunset:
> 1609809312.0, txBatteryStatus: 0, usUnits: 1, windchill: 50.3, windDir:
> 158.0, windGust: 36.0, windGustDir: 158.0, windSpeed: 36.0, windSpeed10:
> 28.0, yearET: 0.0, yearRain: 0.4
>
>
> Here's my syslog from the startup with debug = 1
>
> ------------------------------------------------------------------------------------------------------
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Initializing
> weewx version 4.0.0b9
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Using Python
> 2.7.16 (default, Apr 6 2019, 01:42:57) #012[GCC 8.2.0]
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Platform
> Linux-4.19.75-v7l+-armv7l-with-debian-10.1
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Locale is
> 'en_US.UTF-8'
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Using
> configuration file /home/weewx/weewx.conf
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Loading
> station type Vantage (weewx.drivers.vantage)
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: StdConvert
> target unit is 0x1
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.wxservices: The
> following values will be calculated: altimeter=prefer_hardware,
> appTemp=prefer_hardware, barometer=prefer_hardware,
> beaufort=prefer_hardware, cloudbase=prefer_hardware,
> dewpoint=prefer_hardware, ET=prefer_hardware, heatindex=prefer_hardware,
> humidex=prefer_hardware, inDewpoint=prefer_hardware,
> maxSolarRad=prefer_hardware, pressure=prefer_hardware,
> rainRate=prefer_hardware, windchill=prefer_hardware, windrun=prefer_hardware
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.wxservices: The
> following algorithms will be used for calculations: altimeter=aaASOS,
> maxSolarRad=RS
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Archive will
> use data binding wx_binding
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Record
> generation will be attempted in 'hardware'
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Using archive
> interval of 300 seconds (specified by hardware)
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.restx:
> StationRegistry: Station will not be registered: no station_url specified.
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.restx:
> Wunderground-PWS: Data for station {Manually obfuscated} will be posted
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.restx: PWSWeather:
> Data for station {Manually obfuscated} will be posted
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.restx: CWOP: Data for
> station {Manually obfuscated} will be posted
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.restx: WOW: Posting
> not enabled.
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.restx: AWEKAS: Posting
> not enabled.
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Starting up
> weewx version 4.0.0b9
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Clock error is
> 0.21 seconds (positive is fast)
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Using binding
> 'wx_binding' to database 'weewx.sdb'
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.manager: Starting
> backfill of daily summaries
> Jan 4 13:48:41 raspberrypi weewx[11987] INFO weewx.engine: Starting main
> packet loop.
> Jan 4 13:50:14 raspberrypi dbus-daemon[291]: [system] Activating via
> systemd: service name='org.freedesktop.hostname1'
> unit='dbus-org.freedesktop.hostname1.service' requested by ':1.43'
> (uid=1000 pid=11154 comm="geany ")
> Jan 4 13:50:14 raspberrypi systemd[1]: Starting Hostname Service...
> Jan 4 13:50:14 raspberrypi dbus-daemon[291]: [system] Successfully
> activated service 'org.freedesktop.hostname1'
> Jan 4 13:50:14 raspberrypi systemd[1]: Started Hostname Service.
> Jan 4 13:50:16 raspberrypi weewx[11987] INFO weewx.manager: Added record
> 2021-01-04 13:50:00 PST (1609797000) to database 'weewx.sdb'
> Jan 4 13:50:16 raspberrypi weewx[11987] INFO weewx.manager: Added record
> 2021-01-04 13:50:00 PST (1609797000) to daily summary in 'weewx.sdb'
> Jan 4 13:50:18 raspberrypi weewx[11987] INFO weewx.restx: CWOP: Published
> record 2021-01-04 13:50:00 PST (1609797000)
> Jan 4 13:50:18 raspberrypi weewx[11987] INFO weewx.cheetahgenerator:
> Generated 8 files for report SeasonsReport in 1.98 seconds
> Jan 4 13:50:18 raspberrypi weewx[11987] INFO weewx.restx: PWSWeather:
> Published record 2021-01-04 13:50:00 PST (1609797000)
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.imagegenerator:
> Generated 14 images for SeasonsReport in 0.65 seconds
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.reportengine: Copied 5
> files to /home/weewx/public_html/seasons
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.restx:
> Wunderground-PWS: Published record 2021-01-04 13:50:00 PST (1609797000)
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.cheetahgenerator:
> Generated 6 files for report SmartphoneReport in 0.19 seconds
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.imagegenerator:
> Generated 6 images for SmartphoneReport in 0.25 seconds
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.reportengine: Copied 6
> files to /home/weewx/public_html/smartphone
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.cheetahgenerator:
> Generated 1 files for report MobileReport in 0.06 seconds
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.imagegenerator:
> Generated 4 images for MobileReport in 0.17 seconds
> Jan 4 13:50:19 raspberrypi weewx[11987] INFO weewx.reportengine: Copied 2
> files to /home/weewx/public_html/mobile
> Jan 4 13:50:21 raspberrypi weewx[11987] INFO weewx.cheetahgenerator:
> Generated 14 files for report StandardReport in 1.89 seconds
> Jan 4 13:50:22 raspberrypi weewx[11987] INFO weewx.imagegenerator:
> Generated 12 images for StandardReport in 0.50 seconds
> Jan 4 13:50:22 raspberrypi weewx[11987] INFO weewx.reportengine: Copied
> 14 files to /home/weewx/public_html/std
> Jan 4 13:50:22 raspberrypi weewx[11987] INFO weewx.cheetahgenerator:
> Generated 1 files for report PVW in 0.19 seconds
> Jan 4 13:50:23 raspberrypi weewx[11987] INFO weewx.imagegenerator:
> Generated 11 images for PVW in 0.43 seconds
> Jan 4 13:50:23 raspberrypi weewxd: i:19 1609797023.21 1609778423
> speed:2.0 dir :146.25
> Jan 4 13:50:23 raspberrypi weewxd: i:20 1609797023.21 1609779023
> speed:1.5 dir :123.75
> Jan 4 13:50:23 raspberrypi weewxd: i:21 1609797023.21 1609779623
> speed:0.5 dir :112.5
> Jan 4 13:50:23 raspberrypi weewxd: i:22 1609797023.21 1609780223
> speed:3.5 dir :168.75
> Jan 4 13:50:23 raspberrypi weewxd: i:23 1609797023.21 1609780823
> speed:1.5 dir :315.0
> Jan 4 13:50:23 raspberrypi weewxd: i:24 1609797023.21 1609781423
> speed:0.0 dir :None
> Jan 4 13:50:23 raspberrypi weewxd: i:25 1609797023.21 1609782023
> speed:0.5 dir :315.0
> Jan 4 13:50:23 raspberrypi weewxd: i:26 1609797023.21 1609782623
> speed:0.0 dir :None
> Jan 4 13:50:23 raspberrypi weewxd: i:27 1609797023.21 1609783223
> speed:2.0 dir :191.25
> Jan 4 13:50:23 raspberrypi weewxd: i:28 1609797023.21 1609783823
> speed:5.5 dir :270.0
> Jan 4 13:50:23 raspberrypi weewxd: i:29 1609797023.21 1609784423
> speed:6.0 dir :270.0
> Jan 4 13:50:23 raspberrypi weewxd: i:30 1609797023.21 1609785023
> speed:13.5 dir :213.75
> Jan 4 13:50:23 raspberrypi weewxd: i:31 1609797023.21 1609785623
> speed:17.5 dir :236.25
> Jan 4 13:50:23 raspberrypi weewxd: i:32 1609797023.21 1609786223
> speed:19.0 dir :225.0
> Jan 4 13:50:23 raspberrypi weewxd: i:33 1609797023.21 1609786823
> speed:20.0 dir :225.0
> Jan 4 13:50:23 raspberrypi weewxd: i:34 1609797023.21 1609787423
> speed:22.0 dir :213.75
> Jan 4 13:50:23 raspberrypi weewxd: i:35 1609797023.21 1609788023
> speed:24.0 dir :180.0
> Jan 4 13:50:23 raspberrypi weewxd: i:36 1609797023.21 1609788623
> speed:20.5 dir :191.25
> Jan 4 13:50:23 raspberrypi weewxd: i:37 1609797023.21 1609789223
> speed:22.5 dir :225.0
> Jan 4 13:50:23 raspberrypi weewxd: i:38 1609797023.21 1609789823
> speed:22.5 dir :202.5
> Jan 4 13:50:23 raspberrypi weewxd: i:39 1609797023.21 1609790423
> speed:16.5 dir :236.25
> Jan 4 13:50:23 raspberrypi weewxd: i:40 1609797023.21 1609791023
> speed:15.5 dir :191.25
> Jan 4 13:50:23 raspberrypi weewxd: i:41 1609797023.21 1609791623
> speed:22.5 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:42 1609797023.21 1609792223
> speed:21.0 dir :180.0
> Jan 4 13:50:23 raspberrypi weewxd: i:43 1609797023.21 1609792823
> speed:25.5 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:44 1609797023.21 1609793423
> speed:22.5 dir :168.75
> Jan 4 13:50:23 raspberrypi weewxd: i:44 Recent 1609793423 Mon, 04
> Jan 2021 12:50:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: i:45 1609797023.21 1609794023
> speed:26.5 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:45 Recent 1609794023 Mon, 04
> Jan 2021 13:00:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: i:46 1609797023.21 1609794623
> speed:22.5 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:46 Recent 1609794623 Mon, 04
> Jan 2021 13:10:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: i:47 1609797023.21 1609795223
> speed:24.0 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:47 Recent 1609795223 Mon, 04
> Jan 2021 13:20:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: i:48 1609797023.21 1609795823
> speed:27.0 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:48 Recent 1609795823 Mon, 04
> Jan 2021 13:30:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: i:49 1609797023.21 1609796423
> speed:28.0 dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: i:49 Recent 1609796423 Mon, 04
> Jan 2021 13:40:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: i:49 Current 1609796423 Mon, 04
> Jan 2021 13:40:23 +0000
> Jan 4 13:50:23 raspberrypi weewxd: speed:28.0
> Jan 4 13:50:23 raspberrypi weewxd: dir :157.5
> Jan 4 13:50:23 raspberrypi weewxd: imageWindRose:genimages: Generated 1
> images in 0.16 seconds
> Jan 4 13:50:23 raspberrypi weewx[11987] INFO weewx.reportengine: Copied
> 24 files to /home/weewx/public_html/PVW
> Jan 4 13:50:31 raspberrypi weewx[11987] INFO weewx.engine: Main loop
> exiting. Shutting engine down.
> Jan 4 13:50:31 raspberrypi weewx[11987] INFO weewx.engine: Shutting down
> StdReport thread
> Jan 4 13:50:42 raspberrypi weewx[11987] CRITICAL weewx.engine: Keyboard
> interrupt.
> Jan 4 13:50:44 raspberrypi weewx[11987] INFO weewx.reportengine:
> ftpgenerator: Ftp'd 29 files in 21.12 seconds
> Jan 4 13:50:45 raspberrypi systemd[1]: systemd-hostnamed.service:
> Succeeded.
> Jan 4 13:50:50 raspberrypi systemd[1]: Starting LSB: weewx weather
> system...
> Jan 4 13:50:50 raspberrypi weewx[12051] INFO weewx.engine: Initializing
> weewx version 4.0.0b9
> Jan 4 13:50:50 raspberrypi weewx[12051] INFO weewx.engine: Using Python
> 2.7.16 (default, Apr 6 2019, 01:42:57) #012[GCC 8.2.0]
> Jan 4 13:50:50 raspberrypi weewx[12051] INFO weewx.engine: Platform
> Linux-4.19.75-v7l+-armv7l-with-debian-10.1
> Jan 4 13:50:50 raspberrypi weewx[12051] INFO weewx.engine: Locale is
> 'en_US.UTF-8'
> Jan 4 13:50:50 raspberrypi weewx[12051] INFO weewx.engine: PID file is
> /var/run/weewx.pid
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Using
> configuration file /home/weewx/weewx.conf
> Jan 4 13:50:50 raspberrypi weewx[12040]: Starting weewx weather system:
> weewx.
> Jan 4 13:50:50 raspberrypi systemd[1]: Started LSB: weewx weather system.
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Debug is 1
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Initializing
> engine
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Loading
> station type Vantage (weewx.drivers.vantage)
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Driver version is 3.2.0
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Opened up serial port /dev/ttyUSB0; baud 19200; timeout 4.00
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Gentle wake up of console successful
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Hardware type is 17
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage: ISS
> ID is 1
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Hardware name: Vantage Vue
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdTimeSynch
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdTimeSynch
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdConvert
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: StdConvert
> target unit is 0x1
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdConvert
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdCalibrate
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdCalibrate
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdQC
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdQC
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.wxservices.StdWXCalculate
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.manager: Daily
> summary version is 2.0
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.wxservices: The
> following values will be calculated: altimeter=prefer_hardware,
> appTemp=prefer_hardware, barometer=prefer_hardware,
> beaufort=prefer_hardware, cloudbase=prefer_hardware,
> dewpoint=prefer_hardware, ET=prefer_hardware, heatindex=prefer_hardware,
> humidex=prefer_hardware, inDewpoint=prefer_hardware,
> maxSolarRad=prefer_hardware, pressure=prefer_hardware,
> rainRate=prefer_hardware, windchill=prefer_hardware, windrun=prefer_hardware
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.wxservices: The
> following algorithms will be used for calculations: altimeter=aaASOS,
> maxSolarRad=RS
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.wxservices.StdWXCalculate
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdArchive
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Archive will
> use data binding wx_binding
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Record
> generation will be attempted in 'hardware'
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Using archive
> interval of 300 seconds (specified by hardware)
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Use LOOP data
> in hi/low calculations: 1
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdArchive
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.restx.StdStationRegistry
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.restx:
> StationRegistry: Station will not be registered: no station_url specified.
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.restx.StdStationRegistry
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.restx.StdWunderground
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.restx: WU essentials:
> {}
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.restx:
> Wunderground-PWS: Data for station {Manually obfuscated} will be posted
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.restx.StdWunderground
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.restx.StdPWSweather
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.restx: PWSWeather:
> Data for station {Manually obfuscated} will be posted
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.restx.StdPWSweather
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.restx.StdCWOP
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.restx: CWOP: Data for
> station {Manually obfuscated} will be posted
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.restx.StdCWOP
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.restx.StdWOW
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.restx: WOW: Posting
> not enabled.
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.restx.StdWOW
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.restx.StdAWEKAS
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.restx: AWEKAS: Posting
> not enabled.
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.restx.StdAWEKAS
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdPrint
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdPrint
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.manager: Daily
> summary version is 2.0
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Loading
> service weewx.engine.StdReport
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.engine: Finished
> loading service weewx.engine.StdReport
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Starting up
> weewx version 4.0.0b9
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Gentle wake up of console successful
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.manager: Daily
> summary version is 2.0
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.manager: Daily
> summary version is 2.0
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Clock error is
> 0.20 seconds (positive is fast)
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Using binding
> 'wx_binding' to database 'weewx.sdb'
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.manager: Starting
> backfill of daily summaries
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Getting archive packets since 2021-01-04 13:50:00 PST (1609797000)
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Gentle wake up of console successful
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Retrieving 0 page(s); starting index= 0
> Jan 4 13:50:50 raspberrypi weewx[12055] INFO weewx.engine: Starting main
> packet loop.
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Gentle wake up of console successful
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Requesting 200 LOOP packets.
> Jan 4 13:50:50 raspberrypi weewx[12055] DEBUG weewx.drivers.vantage:
> Gentle wake up of console successful
>
>
> wee_debug --info
>
> ------------------------------------------------------------------------------------------------------
> Using configuration file /home/weewx/weewx.conf
> Using database binding 'wx_binding', which is bound to database
> 'archive_sqlite'
>
> System info
> Platform: Linux-4.19.75-v7l+-armv7l-with-debian-10.1
> Python Version: 2.7.16
>
> Load Information
> 1 minute load average: 0.19
> 5 minute load average: 0.24
> 15 minute load average: 0.20
>
> General Weewx info
> Weewx version 4.0.0b9 detected.
>
> Station info
> Station type: Vantage
> Driver: weewx.drivers.vantage
>
> Driver info
> [Vantage]
> # This section is for the Davis Vantage series of weather stations.
>
> # Connection type: serial or ethernet
> # serial (the classic VantagePro)
> # ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
> type = serial
>
> # If the connection type is serial, a port must be specified:
> # Debian, Ubuntu, Redhat, Fedora, and SuSE:
> # /dev/ttyUSB0 is a common USB port name
> # /dev/ttyS0 is a common serial port name
> # BSD:
> # /dev/cuaU0 is a common serial port name
> port = /dev/ttyUSB0
> #port = /dev/ttyS0
>
> # If the connection type is ethernet, an IP Address/hostname is
> required:
> host = 1.2.3.4
>
> ######################################################
> # The rest of this section rarely needs any attention.
> # You can safely leave it "as is."
> ######################################################
>
> # Serial baud rate (usually 19200)
> baudrate = 19200
>
> # TCP port (when using the WeatherLinkIP)
> tcp_port = 22222
>
> # TCP send delay (when using the WeatherLinkIP):
> tcp_send_delay = 0.5
>
> # The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both
> loop_request = 1
>
> # The id of your ISS station (usually 1). If you use a wind meter
> connected
> # to a anemometer transmitter kit, use its id
> iss_id = 1
>
> # How long to wait for a response from the station before giving up (in
> # seconds; must be greater than 2)
> timeout = 4
>
> # How long to wait before trying again (in seconds)
> wait_before_retry = 1.2
>
> # How many times to try before giving up:
> max_tries = 4
>
> # Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
> model_type = 2
>
> # The driver to use:
> driver = weewx.drivers.vantage
>
> Currently installed extensions
> No extensions installed
>
> Archive info
> Database name: weewx.sdb
> Table name: archive
> Version 2.0
> Unit system: 1 (US)
> First good timestamp: 2020-01-17 14:35:00 PST (1579300500)
> Last good timestamp: 2021-01-04 14:10:00 PST (1609798200)
> Number of records: 101479
> weewx (weewx.conf) is set to use an archive interval of 300 seconds.
> The station hardware was not interrogated in determining archive
> interval.
>
> Databases configured in weewx.conf
> Database name: weewx.sdb
> Database driver: weedb.sqlite
>
> Database name: weewx
> Database driver: weedb.mysql
> Database host: localhost
>
>
> Parsed and obfuscated weewx.conf
> # WEEWX CONFIGURATION FILE
> #
> # Copyright (c) 2009-2019 Tom Keffer <tke...@gmail.com>
> # See the file LICENSE.txt for your rights.
>
>
> ##############################################################################
>
> # This section is for general configuration information.
>
> # Set to 1 for extra debug info, otherwise comment it out or set to zero
> debug = 1
>
> # Root directory of the weewx data file hierarchy for this station
> WEEWX_ROOT = /home/weewx
>
> # Whether to log successful operations
> log_success = True
>
> # Whether to log unsuccessful operations
> log_failure = True
>
> # How long to wait before timing out a socket (FTP, HTTP) connection
> socket_timeout = 20
>
> # Do not modify this. It is used when installing and updating weewx.
> version = 4.0.0b9
>
>
> ##############################################################################
>
> # This section is for information about the station.
>
> [Station]
>
> # Description of the station location
> location = Palomino Valley Weather
>
> # Latitude and longitude in decimal degrees
> latitude = 39.8308
> longitude = -119.6427
>
> # Altitude of the station, with unit it is in. This is downloaded from
> # from the station if the hardware supports it.
> altitude = 4210, foot # Choose 'foot' or 'meter' for unit
>
> # If you have a website, you may specify an URL
> #station_url = http://www.example.com
>
> # The start of the rain year (1=January; 10=October, etc.). This is
> # downloaded from the station if the hardware supports it.
> rain_year_start = 10
>
> # Start of week (0=Monday, 6=Sunday)
> week_start = 6
>
> # Set to type of station hardware. There must be a corresponding stanza
> # in this file with a 'driver' parameter indicating the driver to be
> used.
> #station_type = Vantage
> station_type = Vantage
>
>
> ##############################################################################
>
> [Vantage]
> # This section is for the Davis Vantage series of weather stations.
>
> # Connection type: serial or ethernet
> # serial (the classic VantagePro)
> # ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
> type = serial
>
> # If the connection type is serial, a port must be specified:
> # Debian, Ubuntu, Redhat, Fedora, and SuSE:
> # /dev/ttyUSB0 is a common USB port name
> # /dev/ttyS0 is a common serial port name
> # BSD:
> # /dev/cuaU0 is a common serial port name
> port = /dev/ttyUSB0
> #port = /dev/ttyS0
>
> # If the connection type is ethernet, an IP Address/hostname is
> required:
> host = 1.2.3.4
>
> ######################################################
> # The rest of this section rarely needs any attention.
> # You can safely leave it "as is."
> ######################################################
>
> # Serial baud rate (usually 19200)
> baudrate = 19200
>
> # TCP port (when using the WeatherLinkIP)
> tcp_port = 22222
>
> # TCP send delay (when using the WeatherLinkIP):
> tcp_send_delay = 0.5
>
> # The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both
> loop_request = 1
>
> # The id of your ISS station (usually 1). If you use a wind meter
> connected
> # to a anemometer transmitter kit, use its id
> iss_id = 1
>
> # How long to wait for a response from the station before giving up (in
> # seconds; must be greater than 2)
> timeout = 4
>
> # How long to wait before trying again (in seconds)
> wait_before_retry = 1.2
>
> # How many times to try before giving up:
> max_tries = 4
>
> # Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
> model_type = 2
>
> # The driver to use:
> driver = weewx.drivers.vantage
>
>
> ##############################################################################
>
> [Simulator]
> # This section is for the weewx weather station simulator
>
> # The time (in seconds) between LOOP packets.
> loop_interval = 2.5
>
> # The simulator mode can be either 'simulator' or 'generator'.
> # Real-time simulator. Sleep between each LOOP packet.
> mode = simulator
> # Generator. Emit LOOP packets as fast as possible (useful for
> testing).
> #mode = generator
>
> # The start time. Format is YYYY-mm-ddTHH:MM. If not specified, the
> default
> # is to use the present time.
> #start = 2011-01-01T00:00
>
> # The driver to use:
> driver = weewx.drivers.simulator
>
>
> ##############################################################################
>
> # This section is for uploading data to Internet sites
>
> [StdRESTful]
>
> [[StationRegistry]]
> # To register this weather station with weewx, set this to true
> register_this_station = true
>
> [[AWEKAS]]
> # This section is for configuring posts to AWEKAS.
>
> # If you wish to do this, set the option 'enable' to true,
> # and specify a username and password.
> # To guard against parsing errors, put the password in quotes.
> enable = false
> username = XXX obfuscated by wee_debug XXX
> password = XXX obfuscated by wee_debug XXX
>
> [[CWOP]]
> # This section is for configuring posts to CWOP.
>
> # If you wish to do this, set the option 'enable' to true,
> # and specify the station ID (e.g., CW1234).
> enable = true
> station = XXX obfuscated by wee_debug XXX
>
> # If this is an APRS (radio amateur) station, uncomment
> # the following and replace with a passcode (e.g., 12345).
> #passcode = replace_me (APRS stations only)
>
> [[PWSweather]]
> # This section is for configuring posts to PWSweather.com.
>
> # If you wish to do this, set the option 'enable' to true,
> # and specify a station and password.
> # To guard against parsing errors, put the password in quotes.
> enable = true
> station = XXX obfuscated by wee_debug XXX
> password = XXX obfuscated by wee_debug XXX
>
> [[WOW]]
> # This section is for configuring posts to WOW.
>
> # If you wish to do this, set the option 'enable' to true,
> # and specify a station and password.
> # To guard against parsing errors, put the password in quotes.
> enable = false
> station = XXX obfuscated by wee_debug XXX
> password = XXX obfuscated by wee_debug XXX
>
> [[Wunderground]]
> # This section is for configuring posts to the Weather Underground.
>
> # If you wish to do this, set the option 'enable' to true,
> # and specify a station (e.g., 'KORHOODR3') and password.
> # To guard against parsing errors, put the password in quotes.
> enable = true
> station = XXX obfuscated by wee_debug XXX
> password = XXX obfuscated by wee_debug XXX
>
> # If you plan on using wunderfixer, set the following
> # to your API key:
> api_key = XXX obfuscated by wee_debug XXX
>
> # Set the following to True to have weewx use the WU "Rapidfire"
> # protocol. Not all hardware can support it. See the User's Guide.
> rapidfire = False
>
>
> ##############################################################################
>
> # This section specifies what reports, using which skins, to generate.
>
> [StdReport]
>
> # Where the skins reside, relative to WEEWX_ROOT
> SKIN_ROOT = skins
>
> # Where the generated reports should go, relative to WEEWX_ROOT
> HTML_ROOT = public_html/std
>
> # The database binding indicates which data should be used in reports.
> data_binding = wx_binding
>
> # Whether to log a successful operation
> log_success = True
>
> # Whether to log an unsuccessful operation
> log_failure = False
>
> # Each of the following subsections defines a report that will be run.
> # See the customizing guide to change the units, plot types and line
> # colors, modify the fonts, display additional sensor data, and other
> # customizations. Many of those changes can be made here by overriding
> # parameters, or by modifying templates within the skin itself.
>
> [[SeasonsReport]]
> # The SeasonsReport uses the 'Seasons' skin, which contains the
> # images, templates and plots for the report.
> skin = Seasons
> enable = true
> HTML_ROOT = public_html/seasons
>
> [[SmartphoneReport]]
> # The SmartphoneReport uses the 'Smartphone' skin, and the images
> and
> # files are placed in a dedicated subdirectory.
> skin = Smartphone
> enable = true
> HTML_ROOT = public_html/smartphone
>
> [[MobileReport]]
> # The MobileReport uses the 'Mobile' skin, and the images and files
> # are placed in a dedicated subdirectory.
> skin = Mobile
> enable = true
> HTML_ROOT = public_html/mobile
>
> [[StandardReport]]
> # This is the old "Standard" skin. By default, it is not enabled.
> skin = Standard
> enable = true
> HTML_ROOT = public_html/std
>
> [[PVW]]
> # What skin this report should be based on:
> skin = PVW
> enable = true
> HTML_ROOT = public_html/PVW
> #HTML_ROOT = public_html/
>
> [[FTP]]
> # FTP'ing the results to a webserver is treated as just another
> report,
> # albeit one with an unusual report generator!
> skin = Ftp
>
> # If you wish to use FTP, set "enable" to "true", then
> # fill out the next four lines.
> # Use quotes around passwords to guard against parsing errors.
> enable = true
> user = XXX obfuscated by wee_debug XXX
> password = XXX obfuscated by wee_debug XXX
> server = ftp.techcpg.com
> path = /
>
> # Set to True for an FTP over TLS (FTPS) connection. Not all
> servers
> # support this.
> secure_ftp = False
>
> # To upload files from something other than what HTML_ROOT is set
> # to above, specify a different HTML_ROOT here.
> HTML_ROOT = public_html/PVW
>
> # Most FTP servers use port 21
> port = 21
>
> # Set to 1 to use passive mode, zero for active mode
> passive = 1
>
> [[RSYNC]]
> # rsync'ing to a webserver is treated as just another report
> skin = Rsync
>
> # If you wish to use rsync, you must configure passwordless ssh
> using
> # public/private key authentication from the user account that
> weewx
> # runs to the user account on the remote machine where the files
> # will be copied.
> #
> # If you wish to use rsync, set "enable" to "true", then
> # fill out server, user, and path.
> # The server should appear in your .ssh/config file.
> # The user is the username used in the identity file.
> # The path is the destination directory, such as
> /var/www/html/weather.
> # Be sure that the user has write permissions on the destination!
> enable = false
> server = replace_me
> user = XXX obfuscated by wee_debug XXX
> path = replace_me
>
> # To upload files from something other than what HTML_ROOT is set
> # to above, specify a different HTML_ROOT here.
> #HTML_ROOT = public_html
>
> # Rsync can be configured to remove files from the remote server if
> # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if
> you
> # make a mistake in the remote path, you could could
> unintentionally
> # cause unrelated files to be deleted. Set to 1 to enable remote
> file
> # deletion, zero to allow files to accumulate remotely.
> delete = 0
>
> ####
>
> # Various options for customizing your reports.
>
> [[Defaults]]
>
> [[[Units]]]
>
> # The following section sets what unit to use for each unit
> group.
> # NB: The unit is always in the singular. I.e.,
> 'mile_per_hour',
> # NOT 'miles_per_hour'
> [[[[Groups]]]]
>
> group_altitude = foot # Options are 'foot' or 'meter'
> group_degree_day = degree_F_day # Options are
> 'degree_F_day' or 'degree_C_day'
> group_distance = mile # Options are 'mile' or 'km'
> group_pressure = inHg # Options are 'inHg', 'mmHg',
> 'mbar', or 'hPa'
> group_rain = inch # Options are 'inch', 'cm', or 'mm'
> group_rainrate = inch_per_hour # Options are
> 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour'
> group_speed = mile_per_hour # Options are
> 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second'
> group_speed2 = mile_per_hour2 # Options are
> 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2'
> group_temperature = degree_F # Options are 'degree_F'
> or 'degree_C'
>
> # The following section sets the formatting for each type of
> unit.
> [[[[StringFormats]]]]
>
> centibar = %.0f
> cm = %.2f
> cm_per_hour = %.2f
> degree_C = %.1f
> degree_F = %.1f
> degree_compass = %.0f
> foot = %.0f
> hPa = %.1f
> hour = %.1f
> inHg = %.3f
> inch = %.2f
> inch_per_hour = %.2f
> km = %.1f
> km_per_hour = %.0f
> km_per_hour2 = %.1f
> knot = %.0f
> knot2 = %.1f
> mbar = %.1f
> meter = %.0f
> meter_per_second = %.1f
> meter_per_second2 = %.1f
> mile = %.1f
> mile_per_hour = %.0f
> mile_per_hour2 = %.1f
> mm = %.1f
> mmHg = %.1f
> mm_per_hour = %.1f
> percent = %.0f
> second = %.0f
> uv_index = %.1f
> volt = %.1f
> watt_per_meter_squared = %.0f
> NONE = " N/A"
>
> # The following section overrides the label used for each type
> of unit
> [[[[Labels]]]]
>
> meter = " meter", " meters" # You may prefer "metre".
> day = " day", " days"
> hour = " hour", " hours"
> minute = " minute", " minutes"
> second = " second", " seconds"
> NONE = ""
>
> # The following section sets the format for each time scale.
> # The values below will work in every locale, but they may not
> look
> # particularly attractive.
> [[[[TimeFormats]]]]
>
> hour = %H:%M
> day = %X
> week = %X (%A)
> month = %x %X
> year = %x %X
> rainyear = %x %X
> current = %x %X
> ephem_day = %X
> ephem_year = %x %X
>
> [[[[Ordinates]]]]
>
> # Ordinal directions. The last one is for no wind direction
> directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW,
> WSW, W, WNW, NW, NNW, N/A
>
> # The following section sets the base temperatures used for the
> # calculation of heating, cooling, and growing degree-days.
> [[[[DegreeDays]]]]
>
> # Base temperature for heating days, with unit:
> heating_base = 65, degree_F
> # Base temperature for cooling days, with unit:
> cooling_base = 65, degree_F
> # Base temperature for growing days, with unit:
> growing_base = 50, degree_F
>
> # A trend takes a difference across a time period. The
> following
> # section sets the time period, and how big an error is
> allowed to
> # still be counted as the start or end of a period.
> [[[[Trend]]]]
>
> time_delta = 10800 # 3 hours
> time_grace = 300 # 5 minutes
>
> # The labels to be used for each observation type
> [[[Labels]]]
>
> # Set to hemisphere abbreviations suitable for your location:
> hemispheres = N, S, E, W
>
> # Formats to be used for latitude whole degrees, longitude
> whole
> # degrees, and minutes:
> latlon_formats = %02d, %03d, %05.2f
>
> # Generic labels, keyed by an observation type.
> [[[[Generic]]]]
> barometer = Barometer
> dewpoint = Dew Point
> ET = ET
> heatindex = Heat Index
> inHumidity = Inside Humidity
> inTemp = Inside Temperature
> outHumidity = Humidity
> outTemp = Outside Temperature
> radiation = Radiation
> rain = Rain
> rainRate = Rain Rate
> UV = UV Index
> windDir = Wind Direction
> windGust = Gust Speed
> windGustDir = Gust Direction
> windSpeed = Wind Speed
> windchill = Wind Chill
> windgustvec = Gust Vector
> windvec = Wind Vector
> extraTemp1 = Temperature1
> extraTemp2 = Temperature2
> extraTemp3 = Temperature3
>
> # Sensor status indicators
>
> rxCheckPercent = Signal Quality
> txBatteryStatus = Transmitter Battery
> windBatteryStatus = Wind Battery
> rainBatteryStatus = Rain Battery
> outTempBatteryStatus = Outside Temperature Battery
> inTempBatteryStatus = Inside Temperature Battery
> consBatteryVoltage = Console Battery
> heatingVoltage = Heating Battery
> supplyVoltage = Supply Voltage
> referenceVoltage = Reference Voltage
>
> [[[Almanac]]]
>
> # The labels to be used for the phases of the moon:
> moon_phases = New, Waxing crescent, First quarter, Waxing
> gibbous, Full, Waning gibbous, Last quarter, Waning crescent
>
>
> ##############################################################################
>
> # This service acts as a filter, converting the unit system coming from
> # the hardware to a unit system in the database.
>
> [StdConvert]
>
> # The target_unit affects only the unit system in the database. Once
> # chosen it cannot be changed without converting the entire database.
> # Modification of target_unit after starting weewx will result in
> # corrupt data - the database will contain a mix of US and METRIC data.
> #
> # The value of target_unit does not affect the unit system for
> # reporting - reports can display US, Metric, or any combination of
> units.
> #
> # In most cases, target_unit should be left as the default: US
> #
> # In particular, those migrating from a standard wview installation
> # should use US since that is what the wview database contains.
>
> # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
> target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
>
>
> ##############################################################################
>
> # This section can adjust data using calibration expressions.
>
> [StdCalibrate]
>
> [[Corrections]]
> # For each type, an arbitrary calibration expression can be given.
> # It should be in the units defined in the StdConvert section.
> # Example:
> foo = foo + 0.2
>
>
> ##############################################################################
>
> # This section is for quality control checks. If units are not specified,
> # values must be in the units defined in the StdConvert section.
>
> [StdQC]
>
> [[MinMax]]
> barometer = 26, 32.5, inHg
> pressure = 24, 34.5, inHg
> outTemp = -40, 120, degree_F
> inTemp = 10, 120, degree_F
> outHumidity = 0, 100
> inHumidity = 0, 100
> windSpeed = 0, 120, mile_per_hour
> rain = 0, 10, inch
>
>
> ##############################################################################
>
> # This section controls the origin of derived values.
>
> [StdWXCalculate]
>
> [[Calculations]]
> # How to calculate derived quantities. Possible values are:
> # hardware - use the value provided by hardware
> # software - use the value calculated by weewx
> # prefer_hardware - use value provide by hardware if available,
> # otherwise use value calculated by weewx
>
> pressure = prefer_hardware
> barometer = prefer_hardware
> altimeter = prefer_hardware
> windchill = prefer_hardware
> heatindex = prefer_hardware
> dewpoint = prefer_hardware
> inDewpoint = prefer_hardware
> rainRate = prefer_hardware
>
>
> ##############################################################################
>
> # For hardware that supports it, this section controls how often the
> # onboard clock gets updated.
>
> [StdTimeSynch]
>
> # How often to check the weather station clock for drift (in seconds)
> clock_check = 14400
>
> # How much it can drift before we will correct it (in seconds)
> max_drift = 5
>
>
> ##############################################################################
>
> # This section is for configuring the archive service.
>
> [StdArchive]
>
> # If the station hardware supports data logging then the archive
> interval
> # will be downloaded from the station. Otherwise, specify it (in
> seconds).
> archive_interval = 300
>
> # If possible, new archive records are downloaded from the station
> # hardware. If the hardware does not support this, then new archive
> # records will be generated in software.
> # Set the following to "software" to force software record generation.
> record_generation = hardware
>
> # Whether to include LOOP data in hi/low statistics
> loop_hilo = True
>
> # The data binding used to save archive records
> data_binding = wx_binding
>
>
> ##############################################################################
>
> # This section binds a data store to a database.
>
> [DataBindings]
>
> [[wx_binding]]
> # The database must match one of the sections in [Databases].
> # This is likely to be the only option you would want to change.
> database = archive_sqlite
> # The name of the table within the database
> table_name = archive
> # The manager handles aggregation of data for historical summaries
> manager = weewx.manager.DaySummaryManager
> # The schema defines the structure of the database.
> # It is *only* used when the database is created.
> schema = schemas.wview_extended.schema
>
>
> ##############################################################################
>
> # This section defines various databases.
>
> [Databases]
>
> # A SQLite database is simply a single file
> [[archive_sqlite]]
> database_name = weewx.sdb
> database_type = SQLite
>
> # MySQL
> [[archive_mysql]]
> database_name = weewx
> database_type = MySQL
>
>
> ##############################################################################
>
> # This section defines defaults for the different types of databases.
>
> [DatabaseTypes]
>
> # Defaults for SQLite databases
> [[SQLite]]
> driver = weedb.sqlite
> # Directory in which the database files are located
> SQLITE_ROOT = /home/weewx/archive
>
> # Defaults for MySQL databases
> [[MySQL]]
> driver = weedb.mysql
> # The host where the database is located
> host = localhost
> # The user name for logging in to the host
> user = XXX obfuscated by wee_debug XXX
> # The password for the user name (quotes guard against parsing
> errors)
> password = XXX obfuscated by wee_debug XXX
>
>
> ##############################################################################
>
> # This section configures the internal weewx engine.
>
> [Engine]
>
> [[Services]]
> # This section specifies the services that should be run. They are
> # grouped by type, and the order of services within each group
> # determines the order in which the services will be run.
> prep_services = weewx.engine.StdTimeSynch
> data_services = ,
> process_services = weewx.engine.StdConvert,
> weewx.engine.StdCalibrate, weewx.engine.StdQC,
> weewx.wxservices.StdWXCalculate
> archive_services = weewx.engine.StdArchive
> restful_services = weewx.restx.StdStationRegistry,
> weewx.restx.StdWunderground, weewx.restx.StdPWSweather,
> weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
> report_services = weewx.engine.StdPrint, weewx.engine.StdReport
>
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to weewx-user+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/532a7e53-a980-4b5a-b576-add73b13bd0cn%40googlegroups.com.
