Ok 1.1 came with initial install.
Found 1.7 & installed
Thanks for those links Mike. That helped
I got 1.7 TX & RX with power out now. It was a setting in the Rig.
Now I'm having trouble with power out in FlDigi because I changed a setting in
the rig.
I bet when I go back to windows Ill have to change the rig.
Writing settings down for Linux
73 Thanks Mike
N4ABN Eddy
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: Michael Black <[email protected]>
Sent: Tuesday, February 28, 2017 9:05:52 PM
To: WSJT software development
Subject: Re: [wsjt-devel] IC-7300 USB-D --> IC-7300 control lost
1.1? That would be a really old version. The 7300 wasn't in that version.
Can't you compile a more recent version?
de Mike W9MDB
On Tue, Feb 28, 2017 at 9:15 PM, signalhz signalhz
<[email protected]<mailto:[email protected]>> wrote:
I have similar problems
I cant get WSJT-X v 1.1, r3496 to work using rig control while on Linux Mint
18.1 64 bit 'Serena' & cant get any audio to the programs from the USB Codec. I
get "Failed to start audio input stream. " & "PortAudio says requested sound
card format not supported. I am using Timewave Navigator. I don't see Icom 7300
in the drop down list for rig control. I am not real familiar with Linux Mint
yet.
I have FlDigi working fine on Linux
Now on Windows some reason WSJT-X loses audio to TX some times but not often. I
have to close the program & re-open it to get audio back.
Help would be appreciated.
73 Eddy N4ABN
Get Outlook for iOS<https://aka.ms/o0ukef>
_____________________________
From: Pino Zollo <[email protected]<mailto:[email protected]>>
Sent: Tuesday, February 28, 2017 4:01 PM
Subject: [wsjt-devel] IC-7300 USB-D --> IC-7300 control lost
To: <[email protected]<mailto:[email protected]>>
Hi Bill,
El 28/02/17 a las 15:45,
[email protected]<mailto:[email protected]>
escribió:
> what version of WSJT-X are you using?
1.7.0 last version distributed via PPA on Mint 17.3
>
> The WSJT-X "Settings->Radio->Mode" options determine if WSJT-X controls
> the mode of your rig and whether USB or USB-DATA mode is used.
>
Found the solution into the WSJT-X configuration....now it is stable in
USB-D.
> With Icom rigs you must disable "CI-V Transceive Mode" in the rig's
> menu, this option which is on by default causes unsolicited CAT traffic
> that can give unexpected and undesirable behaviour.
>
TU done...
> You should also do a basic RFI check by doing a test transmission into a
> dummy load or at least on minimum power on the rig. There have been a
> few reports of what appears to be RFI issues with the USB interface on
> the IC-7300.
The problem is present also in RX only, without TXing.
...after few minutes of operation the PC loses the control of the radio
and opens a window to ask for retry or leave.
...also the audio gets lost and I have to restart WSJT-x to get the
control again.
>
> 73
> Bill
> G4WJS.
Best 73
Pino ZP4KFX
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org<http://SlashDot.org>! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]<mailto:[email protected]>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]<mailto:[email protected]>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
