I had issues to but on window 10 platform. I used the FT5000 rig, everything burst into life when I switched over from FTdx101D
Ken.. G0ORH Sent from my iPad > On 24 May 2020, at 01:02, John Zantek <j...@zantek.net> wrote: > > Bill, > Many new 101MP owners in the PNW have been experiencing some setup issues, > resulting in lots of phone calls. > Have you been able to talk to the rig with any other S/W via USB and with > what virtual settings? > Is the PC using USB 2.0 or 3.x ? The 101MP is unfortunately persnickety in > that regard. > No hubs, right? > 73 John W7CD > > From: Bill [mailto:brightl...@gmail.com] > Sent: Saturday, May 23, 2020 3:59 PM > To: WSJT software development > Subject: Re: [wsjt-devel] (no subject) > > Hi, > > Thanks for the quick response. I just tried HandShake = NONE and I have > the same result - Rig Failure - HamLib Error. > > Any other suggestions? > > Thanks! > > Bill - AK6A > > On Sat, May 23, 2020 at 3:32 PM Bill Somerville <g4...@classdesign.com> wrote: > On 23/05/2020 23:16, Bill wrote: > I am having an issue connecting a Yaesu FTDX-101MP to WSJT-X on a Mac. I’m > able to get the receive Audio Codec to work properly and I can see decodes > but I get a “Rig Failure - Hamlib Error - Invalid configuration while opening > connection to rig” whenever I do a Test CAT. I am unable to get WSJT-X to > establish control communications with the radio. I’ve seen online suggestions > that say use the HamLib FT-991 selection. I am using the regular WSJT-X > version 2.1.2. I am also just using a USB cable from the radio to the Mac > which is running High Sierra. I am using the following settings: > > > > WSJT-X > > > > RADIO TAB > > > > Rig: Yaesu FT-991 > > > > Serial Port: /dev/cu.SLAB_USBtoUART1 > > Note: Installed latest Silicon Labs Drivers - Also Available selections: > > /dev/tty.SLAB_USBtoUART1 > > /dev/cu.SLAB_USBtoUART > > /dev/tty.SLAB_USBtoUART > > > > Baud Rate: 38400 > > Polling Interval: 1S > > Data Bits: Eight > > Stop Bits: Two > > Handshake: Hardware > > Force Control Lines: Both Empty > > > > PTT Method: CAT > > Mode: None > > Split: Rig > > > > AUDIO Tab > > > > Input - USB AUDIO CODEC > Output - USB AUDIO CODEC > > FTDX101MP Menu > > > > FUNC --> Operation Settings > General > 232C RATE - 38400 > CAT RATE - 38400 > > FUNC --> RADIO SETTINGS > MODE SSB > SSB MOD SOURCE - REAR > REAR SELECT - USB > RPORT GAIN - 10 > DATA MODE SOURCE - REAR (This is the default) > REAR SELECT - USB > DATA OUT LEVEL - 10 > RPORT GAIN - 10 > > RADIO MAIN PANEL & DISPLAY > > > > > > R.FIL - 3kHz > WIDTH - 4000Hz > > > APPLE COMPUTER > > > > USB AUDIO CODEC 1 Format: 2 ch 16-bit Integer 48 kHz > USB AUDIO CODEC 2 Format: 2 ch 16-bit Integer 48 kHz > > > > > > > > Any ideas what might be the issue in getting this going? Has anyone else been > able to get a FTDX-101MP working with WSJT-X? Do I need to install a newer > version of HamLib for this new radio? > > > > Thanks! > > > > Bill - AK6A > > Hi Bill, > > try with "Settings->Radio->Handshake->None". > > 73 > Bill > G4WJS. > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel