Hi, Is there a file /bin/fusermount on your server? Your users have to be in the same group than that file.
Michael Am 15.05.2014 13:30, schrieb Neal Becker: > Just to clarify, my question is, is group fuse used by x2goprint on fedora > 20, which does not seem to otherwise use a fuse group? If so, I could just > try making one - but then if that's the case x2goprint rpm should have done > this - or else it should require the package that does. > > > On Thu, May 15, 2014 at 7:27 AM, Neal Becker <ndbeck...@gmail.com> wrote: > >> I'm not sure fedora uses a fuse group. I have several fuse packages >> installed but no fuse group. There is no package called fuse-utils on >> fedora. >> I see there is a group x2goprint on the server - I'm wondering if perhaps >> this group is used instead? >> >> >> On Thu, May 15, 2014 at 7:20 AM, Mike Gabriel < >> mike.gabr...@das-netzwerkteam.de> wrote: >> >>> Hi Neal, >>> >>> On Debian you have to install the fuse-utils package to get that group... >>> >>> Mike >>> >>> -- >>> >>> DAS-NETZWERKTEAM >>> mike gabriel, herweg 7, 24357 fleckeby >>> fon: +49 (1520) 1976148 >>> >>> GnuPG Key ID 0x25771B13 >>> mail: mike.gabr...@das-netzwerkteam.de, http://das-netzwerkteam.de >>> >>> >>> ----- Original message ----- >>>> There is no fuse group on the server. >>>> There is not on the client either, although the client does use fuse. >>>> >>>> Are you sure there is a fuse group on fedora 20? >>>> >>>> >>>> On Thu, May 15, 2014 at 2:15 AM, Mike Gabriel < >>>> mike.gabr...@das-netzwerkteam.de> wrote: >>>> >>>>> Hi Neal, >>>>> >>>>> On Mi 14 Mai 2014 15:02:10 CEST, Neal Becker wrote: >>>>> >>>>> client and server are both fedora 20. >>>>>> >>>>>> I install cups-x2go on server (and x2goserver-printing). >>>>>> >>>>>> I setup a cups-x2go printer on server on kde environment. >>>>>> >>>>>> On the client I resumed session, with printing enabled (I did not >>> try >>>>>> starting a >>>>>> new session). >>>>>> >>>>>> On server, I can open kde printer settings and try printing a test >>>>>> page. It >>>>>> seems successful. >>>>>> >>>>>> Nothing is printed. >>>>>> >>>>>> How to debug? >>>>>> >>>>> >>>>> Raise the debug level in /etc/cups/cups-x2go.conf and in >>>>> /etc/x2go/x2goserver.conf. Also: use pyhoca-gui with the --libdebug >>>>> cmdline options (PyHoca-GUI is much more verbose and informative with >>>>> such problems compared to X2Go Client). >>>>> >>>>> Also: make sure that you users that shall print are in group "fuse" on >>>>> the server. >>>>> >>>>> Regards, >>>>> Mike >>>>> >>>>> -- >>>>> >>>>> DAS-NETZWERKTEAM >>>>> mike gabriel, herweg 7, 24357 fleckeby >>>>> fon: +49 (1520) 1976 148 >>>>> >>>>> GnuPG Key ID 0x25771B31 >>>>> mail: mike.gabr...@das-netzwerkteam.de, http://das-netzwerkteam.de >>>>> >>>>> freeBusy: >>>>> https://mail.das-netzwerkteam.de/freebusy/m.gabriel%40das- >>>>> netzwerkteam.de.xfb >>>>> >>> >>> >> > > > > _______________________________________________ > x2go-user mailing list > x2go-user@lists.x2go.org > http://lists.x2go.org/listinfo/x2go-user > _______________________________________________ x2go-user mailing list x2go-user@lists.x2go.org http://lists.x2go.org/listinfo/x2go-user