Hey, Craig........ What a Guy! Thanks.... after running the echo
command -- at 9600 baud 8,N,1 I get the Kantronics header in Minicom. I
still don't get anything in Xastir, but then I don't have a radio
attached yet <long story>.
What I am taking away, is My Serial Port Is Functional.
I am assuming that Minicom sets the serial port parameters and leaves
them set. Does that seem reasonable? Is there a way to check as to
what they are set to? Should I be running Xastir with Minicom running
or not?
Many thanx............. jt
Craig Anderson wrote:
You can try:
echo -e “\300\377\300” > /dev/ttyS0
Assuming the baud rate has not changed
out from underneath you on ttyS0. Sometimes
the above command does not "seem" to work
(minicom still doesn't see any command prompt)
until I power-cycle the TNC, then the firmware
banner and command prompt comes right up.
Craig
On Dec 3, 2007, at 6:40 PM, Gerry Creager wrote:
Jim,
my first thought is that the Kam is in KISS mode. Now we need
someone who's Kam savvy to tell you how to tell minicom to get you
out... And then how to get back in. An alternative might be to fire
off the KISS script and see if it then talks to the Kam.
gerry
Jim Tolbert wrote:
Many thanx, Gerry.... Minicom shows "stuff" coming through at 4800
baud..... The guy that lent the KAM to me said that it was header
info. Do you think that it should be ASCII? I get nothing at 2400
or 9600 baud.
Does minicom set the parameters of the port permanently or only when
minicom is running?
Also, running GPSMan allows setting a number of parameters, but not
the interface speed or configuration. Does XASTIR need to have an
interface selected to communicate with the Rinos and if so, which one?
Many thanx.............. jt
Gerry Creager wrote:
Fire up a copy of minicom and see if you can talk to the serial
port as a 'regular' user. If not, you can tell the serial port
that you (as a regular user) can access it... We can help with all
the bad ways to do that...
gerry
Jim Tolbert wrote:
After a disk crash in a laptop, I replaced the hard disk, reloaded
open SUSE 10.2, rebuilt Xastir with all the options ( including
GPSMAN), and reloaded all the maps.. I connected a KAM TNC to the
serial port and selected Serial TNC in the interface control. I
have tried a variety of TNC port identifiers ( /dev/ttyS0, COM1,
etc.) and tried "tnc-startup.kam" as well as "tnc-startup.sys".
Checking the Incoming data window when I turn the KAM on and off
yields nothing. I also tried using a USB to serial converter
with the same null result.
When I connect the laptop to the internet, I can see and plot aprs
stations.
Tomorrow, I will have access to a set of Garmin Rinos for the
afternoon. I have 22 hours to get this going <grin>.
Is it immediately obvious where my error is? Is there a way to
confirm that the serial port is functional? Is there anything
special about connecting a Rino to the laptop that would increase
the likelihood of the system work? Any other suggestions? One
of the other guys has the other laptop that is running Xastir (
from a binary download running on VMWare). Unfortunately, it was
not compiled with GPSMAN so the Rino options are not available.
Many thanks ............. jt
--
Gerry Creager -- [EMAIL PROTECTED]
Texas Mesonet -- AATLT, Texas A&M University
Cell: 979.229.5301 Office: 979.458.4020 FAX: 979.862.3983
Office: 1700 Research Parkway Ste 160, TAMU, College Station, TX 77843
_______________________________________________
Xastir mailing list
Xastir@xastir.org
http://lists.xastir.org/cgi-bin/mailman/listinfo/xastir
--
Jim Tolbert
RiverRidge Consulting, LLC
PO Box 536
Webster, WI 54893
715-866-4398 home office
715-349-8993 fax
[EMAIL PROTECTED]
_______________________________________________
Xastir mailing list
Xastir@xastir.org
http://lists.xastir.org/cgi-bin/mailman/listinfo/xastir