I'm guessing the output of rpm -qa|grep nbfs on management node says that is there. rpm -qa|grep -i genesis will not show that present is my guess. I think upgrading to genesis will allow stuff like this to proceed.
From: "Stagneth, Andre" <[email protected]> To: xCAT Users Mailing list <[email protected]> Date: 03/03/2014 04:38 PM Subject: Re: [xcat-user] runimage didn't find the binary for execution My binary cli was originally MegaCli There are a 32bit and a 64bit executable file MegaCli MegaCli: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), for GNU/Linux 2.2.5, dynamically linked (uses shared libs), stripped file MegaCli64 MegaCli64: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), for GNU/Linux 2.4.0, dynamically linked (uses shared libs), stripped # uname -a Linux xcatimg 2.6.18-164.el5 #1 SMP Thu Sep 3 03:28:30 EDT 2009 x86_64 unknown # ls –lsa /tmp 0 drwxrwxrwt 3 root root 220 Mar 3 15:15 . 0 drwx------ 15 root root 0 Mar 3 14:47 .. 2424 -rwx------ 1 root root 2469692 Mar 3 15:13 MegaCli 2668 -rwx------ 1 root root 2716224 Mar 3 15:13 MegaCli64 4 -rw-r--r-- 1 root root 392 Mar 3 14:47 destiny 4 -rw-r--r-- 1 root root 13 Mar 3 14:47 dhcpserver 508 -r-x------ 1 root root 510200 Mar 3 15:15 libstorelibir-2.so.13.05-0 4 -rw-r--r-- 1 root root 99 Mar 3 14:47 resolv.conf 0 -rw------- 1 root root 0 Mar 3 14:47 sshd 4 -rw------- 1 root root 5 Mar 3 14:47 sshd.pid 0 drwxr-xr-x 2 root root 60 Mar 3 14:47 subsys # ldd MegaCli64 MegaCli64: not an ELF file. # ldd MegaCli checking sub-depends for '/lib/libpthread.so.0' checking sub-depends for '/lib/libncurses.so.5' checking sub-depends for 'not found' checking sub-depends for 'not found' checking sub-depends for 'not found' checking sub-depends for '/lib/libgcc_s.so.1' checking sub-depends for 'not found' checking sub-depends for '/lib/libc.so.0' libpthread.so.0 => /lib/libpthread.so.0 (0x00000000) libncurses.so.5 => /lib/libncurses.so.5 (0x00000000) libdl.so.2 => not found (0x00000000) libstdc++.so.6 => not found (0x00000000) libm.so.6 => not found (0x00000000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x00000000) libc.so.6 => not found (0x00000000) libc.so.0 => /lib/libc.so.0 (0x00000000) /lib/ld-uClibc.so.0 => /lib/ld-uClibc.so.0 (0x00000000) From: David D Johnson [mailto:[email protected]] Sent: Montag, 3. März 2014 22:02 To: xCAT Users Mailing list Subject: Re: [xcat-user] runimage didn't find the binary for execution Can you check with ldd or file on ./cli -- if it's a 32 bit binary and you only have 64 bit libraries, there might be a disconnect. -- ddj On Mar 3, 2014, at 3:55 PM, Stagneth, Andre wrote: Path isn’t the problem nodeset comp430 shell rpower comp430 reset scp cli comp430:/tmp ssh comp430 # ls -lsa /tmp 0 drwxrwxrwt 3 root root 180 Mar 3 14:50 . 0 drwx------ 15 root root 0 Mar 3 14:47 .. 2424 -rwxrwxrwx 1 root root 2469692 Mar 3 14:50 cli 4 -rw-r--r-- 1 root root 392 Mar 3 14:47 destiny 4 -rw-r--r-- 1 root root 13 Mar 3 14:47 dhcpserver 4 -rw-r--r-- 1 root root 99 Mar 3 14:47 resolv.conf 0 -rw------- 1 root root 0 Mar 3 14:47 sshd 4 -rw------- 1 root root 5 Mar 3 14:47 sshd.pid 0 drwxr-xr-x 2 root root 60 Mar 3 14:47 subsys # /tmp/cli -sh: /tmp/cli: not found From: Russell Jones [mailto:[email protected]] Sent: Montag, 3. März 2014 20:52 To: [email protected] Subject: Re: [xcat-user] runimage didn't find the binary for execution Try having the script output pwd first so you know where it's looking. In addition, verify your binary can run inside the nbfs / genesis image manually before trying to automate it. On 3/3/2014 1:42 PM, Stagneth, Andre wrote: Hello, Why the script do not execute the binary? Content of tar: tar tvf run.tgz -rwxr-xr-x root/root 2469692 2014-03-03 20:28 cli -rwxr-xr-x root/root 21 2014-03-03 20:35 runme.sh Content of the script: cat runme.sh ls -lsa cli ./cli –h Output in rcons: run.tgz 100% |*****************************| 661 KB --:--:-- ETA cli runme.sh 2424 -rwxr-xr-x 1 root root 2469692 Mar 3 12:28 cli ./runme.sh: line 2: ./cli: not found Used version of xCat: lsxcatd -v Version 2.7 (svn r11882, built Fri Mar 16 06:32:39 EDT 2012) Thanks in advance André From: Russell Jones [mailto:[email protected]] Sent: Freitag, 28. Februar 2014 20:13 To: [email protected] Subject: Re: [xcat-user] setup RAID controller before installing OS We do exactly this using runimage's first. We just chain it so that the nodes configure their controller and partitions how we need it, reboot, then either install / download the OS On 28.02.2014 10:45, Jonathan Mills wrote: I've briefly looked into this. You can't do it within a kickstart's %pre section because the environment doesn't have enough libraries loaded to allow MegaCli to run. You can do it within a kickstart's %post section, which means you can create raid volumes for secondary drives, and format those. But you still have to have something like a /dev/sda to begin with. Obviously, it's also easy to do this with an xCAT postbootscript, and add the script to the postscripts table or the osimage table. That's what I currently do to create all my secondary drives. If you want to use MegaCli to create all of the raid disks though, I imagine you'd need to boot off the Genesis kernel first. Perhaps as part of the node discovery process. On 02/28/2014 11:35 AM, Stagneth, Andre wrote: Hello, Is there a possibility to integrate a RAID configuration of LSI Controller before installation the OS (SLES11). MegaCli64 cfgclr force a0 MegaCli64 -cfgforeign -clear -a0 MegaCli64 -CfgLdAdd -r1 [$ENC:1,$ENC:2,$ENC:3,$ENC:4] WB RA Cached CachedBadBBU -Cache -a0 (where $ENC is set to the enclosure number – use “./MegaCli64 –pdlist –a0” to find it) MegaCli64 -CfgCacheCadeAdd -r0 -Physdrv [$ENC:0] WT a0 MegaCli64 -LDSetProp NORA –L1 -a0 Thanks in advance, André -- Jonathan Mills Systems Administrator Renaissance Computing Institute UNC-Chapel Hill ------------------------------------------------------------------------------ Flow-based real-time traffic analytics software. Cisco certified tool. Monitor traffic, SLAs, QoS, Medianet, WAAS etc. with NetFlow Analyzer Customize your own dashboards, set traffic alerts and generate reports. Network behavioral analysis & security monitoring. All-in-one tool. http://pubads.g.doubleclick.net/gampad/clk?id=126839071&iu=/4140/ostg.clktrk _______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user ------------------------------------------------------------------------------ Subversion Kills Productivity. Get off Subversion & Make the Move to Perforce. With Perforce, you get hassle-free workflows. Merge that actually works. Faster operations. Version large binaries. Built-in WAN optimization and the freedom to use Git, Perforce or both. Make the move to Perforce. http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.clktrk _______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user ------------------------------------------------------------------------------ Subversion Kills Productivity. Get off Subversion & Make the Move to Perforce. With Perforce, you get hassle-free workflows. Merge that actually works. Faster operations. Version large binaries. Built-in WAN optimization and the freedom to use Git, Perforce or both. Make the move to Perforce. http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.clktrk_______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user ------------------------------------------------------------------------------ Subversion Kills Productivity. Get off Subversion & Make the Move to Perforce. With Perforce, you get hassle-free workflows. Merge that actually works. Faster operations. Version large binaries. Built-in WAN optimization and the freedom to use Git, Perforce or both. Make the move to Perforce. http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.clktrk _______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user
<<inline: graycol.gif>>
------------------------------------------------------------------------------ Subversion Kills Productivity. Get off Subversion & Make the Move to Perforce. With Perforce, you get hassle-free workflows. Merge that actually works. Faster operations. Version large binaries. Built-in WAN optimization and the freedom to use Git, Perforce or both. Make the move to Perforce. http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.clktrk
_______________________________________________ xCAT-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/xcat-user
